Weider Platinum Xp 800 User manual

Model No. 831.153971
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (under seat)
\_Visit our website at
www.weiderplatin um.com
•Assembly
•Adjustments
•Console Operation
•Part List and Drawing
_CAUTION
Read all precautions and instruc-
tions in this manual before
using this equipment. Save this
manual for future reference.
W E I D E R_
RESISTANCE SYSTEM EXERCISER
User's Manual
Sears, Roebuck and Co., Hoffman Estates, IL 60179

TABLE OF CONTENTS
WARNING DECAL PLACEMENT .......................................................... 2
IMPORTANT PRECAUTIONS ............................................................. 3
BEFORE YOU BEGIN ................................................................... 4
ASSEMBLY ........................................................................... 5
ADJUSTMENTS ...................................................................... 14
CONSOLE OPERATION ................................................................ 18
CABLE DIAGRAM ..................................................................... 20
TROUBLESHOOTING .................................................................. 21
EXERCISE GUIDELINES ............................................................... 22
ORDERING REPLACEMENT PARTS ................................................ Back Cover
FULL TEN-YEAR WARRANTY .................................................... Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of
this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before begin-
ning assembly.
WARNING DECAL PLACEMENT
The decals shown here have been
placed on the resistance system. If a
decal is missing or illegible, please call
1-800-999-3756 to order a free replace-
ment decal. Apply the decal in the loca-
tion shown.
•Misuse of this product may result in serious
injury.
•Read user's manual and follow all warnings
and operating instructions prior to use.
•DO not allow children on or around machine.
•Replace label if damaged, illegible, or removed.
2

IMPORTANT PRECAUTIONS
before using the resistance system.
t. Read all instructions in this manual before
using the resistance system. Use the resist-
ance system only as described in this manual.
adequately informed of all precautions.
3. The resistance system is intended for home
use only. Do not use the resistance system In
any commercial, rental, or institutional setting.
11. Pull on the lower cable only while sitting on
the bench or standing on the base plate. Pull
on the high cables only while sitting on the
bench, with the seat in one of the three posi-
tions closest to the upright base, or while
standing on the base plate.
12. The resistance system is designed to be
used with the included resistance. Do not
use the resistance system with any other
type of resistance.
surface. Cover the floor beneath the resist-
ance system to protect the floor.
5, Make sure that all parts are properly tight-
ened each time the resistance system is
used. Replace any worn parts immediately.
6, Keep children under 12 and pets away from
the resistance system at all times.
7. Keep hands and feet away from moving parts.
8. Always wear athletic shoes for foot protec-
tion while exercising.
9. The resistance syat_m is designed to sup-
part a maximum user weight of 300 pounds.
10. The crossbar on the top frame is not
designed to be used for pull-up exercises. Do
not hang on the crossbar.
cables when performing an exercise that
does not require it.
14. Make sure the storage knob is in place and
fully tightened each time the resistance sys-
tem is used.
15. Make sure that the cables remain on the pul-
leys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys.
16. Do not pull on the cables while the resist-
ance level is being adjusted.
17. If you feel pain or dizziness while exercising,
stop Immediately and begin cooling down.
Read all instructions before using. Sears assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3

BEFORE YOU BEGIN
Thank you for selectingthe innovative WELDER®PLAT-
INUM XP8O0 resistancesystem.The resistancesystem
offersa selectionofstationsdesignedtodevelop every
majormusclegroupof the body.Whether yourgoal isto
tone yourbody,builddramaticmusclesize and
strength,or improveyourcardiovascularsystem,the
resistancesystemwillhelpyouto achievethe specific
resultsyouwant.
For your benefit, read this manual carefully before
using the resistance system. If you havequestions
after readingthismanual, call 1-800-4-MY-HOME®
(1-800-469-4663). To helpusassistyou, please note
the productmodelnumber and serialnumberbefore
calling. The modelnumberis 831.153971. The serial
numbercan be found on a decal attachedtothe resist-
ance system(see thefrontcoverofthis manual).
Before readingfurther,please reviewthe drawing below
and familiarize yourselfwiththe parts thatare labeled.
Crossbar
Lat Bar
Console
Squat Backrest
Backrest
Storage Knob
Top Frame
High Pulley
-- ResistanceBar
Squat Pin
Low Pulley
Row Plate
Seat
Seat Knob
Base Plate
Leg Level ASSEMBLED
DIMENSIONS:
Height: 82 in.
Width: 66 in.
Depth: 80 in.
4

ASSEMBLY
This manualisdasigP_dto ensurethatthe resist-
ance systemcan be assembledsuccessfullyby
mostpeople. However,itis importantto realize
that the versatileresistancesystemhasmany
partsand that the assembly processwilltake
time. Most peoplefind_at bysettingaside plenty
oftime, assemblywillgo sm_ly.
Before beginning assembly, carefully read the
following information and instructions:
•Assembly requires two persons.
• Place all parts in acleared area and remove the
packing materials. Do not dispose of the packing
matedals untilassembly is completed.
•For help identifying small parts, use the PART
IDENTIFICATION CHART. Note: Some small
parts may have been pre-attached for shipping. If
a part is not in the parts bag, check to see if it
has been pre-attached.
•Tightenall parts as you assemble them, unless
instructedtodo otherwise.
• As you assemble the resistance system, make
sure all parts are orientedas shown in the draw-
ings.
The included Allen w_ _and the fol-
lowing tools (not included) are required for
assembly:
•Two adjustable wrenches
•One rubber mallet
• One standard screwdriver
•One Phillips screwdriver
•Lubricant, such as grease or petroleum jelly,
and soapy water,
Assemblywillbe more convenientifyou have a
socketset, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
Attach the Base Plate Foot (63) to the Base Plate
(1) with two M4 x 38mm Screws (100).
2. Attach a Wheel (65) to a Wheel Insert (64) with an
M10 x78mm Button Bolt (99) and an M1O Nylon
Locknut (103). Do not overtighten the Locknut;
the Wheel must be able to turn easily.
Attach the Wheel Insert (64) to the Base Plate (1)
with two M4 x 16mm Screws (53) and a Plastic
Foot (36).
Attach the other Wheel (65) in the same man-
ner.
100 p
_.-1 OO
103
64
1
53
99
5

3. 3
Insert the Upper Wire Harness (71) throughthe
hole in the Upright Cover (3). Pull the lower end
of the Upper Wire Harness out of the hole in the
back of the Upright (2).
Attach the Upright Cover (3) and Upright (2) to
the Base Plate (1) with an M10 x 25mm Button
Screw (88), an MIO Washer (106), an M10 x
92mm Button Bolt (83), and an M10 Nylon
Locknut (103).
4. Attach the Row Plate (28) to the Upright (2) with
four M10 x 75ram Button Bolts (84) and four MI0
Nylon Locknuts (103).
103
2_
I O3
71
.2
71
84
6

5. Insert the four connectorsofthe lowerwire har-
ness (C) into the socketsofthe Upper Wire
Harness (71). The connectors should slide easi-
ly into the sockets and snap into place. If a con-
nector does not slide easily and snap into place,
turn the connector over and then insert it.
Make sure that the connectorsand wires appear
as shown in the inset drawing. IF THE CONNEC-
TORS ARE NOT INSERTED PROPERLY, THE
CONSOLE MAY BE DAMAGED WHEN THE
POWER IS TURNED ON.
Pull the excess lower wire hamess ('Cl out of
the Mech Frame 1'61and Push it and the UDDer
Wire Harness (71_ into the Uoriaht (2_.
Insert the Mech Frame (6) into the Base Plate (1).
Attach the Mech Frame to the Upright(2) with a
1/2"x 25mm Screw (85) and a 1/2"Lock Washer
(12). Do not tighten the Screw yet.
Attach the Mech Frame (6) to the Base Plate (1)
withfour M10 Nylon Locknuts(103).
Tighten the 1/2" x 25mm Screw (85).
6. Attach the Leg Lever Bumper (55) to the Leg (5)
with two M5 x 56mm Screws (108).
7, Pullthe Seat Knob (48) and remove the Seat
Carriage (44) from the Rail (not shown).
Attach the Seat (45) to the Seat Carriage (44)
withfour M6 x 16mm Screws (41).
5
6
6 12
85
41
41
7

Pull the Seat Knob (48) out and slide the Seat
Carriage (44) onto the Rail (4) as shown. Engage
the Knob into a hole in the Rail.
Press the Rail Cap (49) onto the Leg (5). Attach
the Leg to the Rail (4) with two M10 x 64mm
Button Bolts (80), four M10 Washers (106), and
two M10 Nylon Locknuts (103).
9. Attach the Rail Insert (31) insideof the Rail (4)
with two M10 x 64mm Button Bolts (80), four M10
Washers (106), and two M10 Nylon Locknuts
(103). Make sure the Bolts go through the indi-
cated holes in the Rail Insert.
10. Lubricate an M10 x 125mm Button Bolt (89) with
grease. Attach the Rail (4) to the Row Plate (28)
with the Bolt, two M10 Washers (106), two 31mm
Spacers (30), and an M10 Nylon Locknut (103).
Do not overtighten the Locknut; the Rail must
be able to pivot easily.
Tighten the Storage Knob (29) into the Row Plate
(28) and the Rail (4).
11. Wet a Squat Arm (20) with soapy water. Slide a
Small Foam Pad (24) and a Short Handgrip (21)
onto the Squat Arm.
Repeat with the other Squat Arm (20).
Tighten the Squat Knob (27) into the Squat
Carriage (19) and the Squat Arm Pivot Tube (not
shown).
9
10
11
103 106 4
48
" Holes on
106 this side
49 80
31
103 106
Holes
4
106
30 106 89
Lubricate
24
21
8

12. Attach the Squat Backrest(25) to the Squat
Carriage (19) with four M6 x 16mm Screws (41).
13. Insert the Squat Pin (66) into the Upright (2).
Slide the Squat Carriage (19) onto the Upright (2).
14. Attach the Top Frame (37) to the Upright (2) with
two M10 x 25mm Button Screws (88), an M10 x
75mm Button Screw (84), three M10 Lock
Washers (75), and an M10 Washer (106).
12
13
14
41
41
66
88
37
84
9

15. Pull the excess Upper Wire Harness (71) out of
the Upright (2). Insertthe connector on the
Console (67) intothe socketon the Upper Wire
Harness. The connector should slide easily into
the socket and snap into place. Iftheconnector
does not slideeasilyand snap intoplace,turnthe
connector over and then insert it.
Make sure thatthe connector and wires appear
as shown in the inset drawing. IF THE CONNEC-
TOR IS NOT INSERTED PROPERLY, THE CON-
SOLE MAY BE DAMAGED WHEN THE POWER
IS TURNED ON.
Push the excess Upper Wire Harness (71) into
the Upright (2).
Attach the Console (67) to the Upright (2) with
four M4 x 70ram Screws (114).
16. Attach a Large Pulley (14) and the Pulley Plate
(68) to the Upright (2) with an M12 x 62mm
Button Bolt (81) and an M12 Nylon Locknut (43).
Do not tighten the Locknut yet.
17. Pull the upper cable (A), which is attached inside
of the Mech Frame (not shown), up between the
Updght (2) and the Pulley Plate (68).
Attach another Large Pulley (14) to the Upright (2)
and PulleyPlate (68) with an M12 x 62mm Button
Bolt (81) and an M12 Nylon Locknut (43). Make
sure that the upper cable (A) is between the
two Pulleys.
Hold the 38mm Spacer (90) insidethe loop ofthe
upper cable (A), and between the Upright(2) and
the Pulley Plate (68). Attach the Spacer with an
M1Ox 58mm Button Screw (42). Make sure the
ends of the cable do not wrap around each
other below the Spacer and the Large Pulleys
(14) used in steps 16 and 17 (refer to the
CABLE DIAGRAM on page 20).
Tighten the M12 Nylon Locknuts (43) used in
steps 16 and 17.
18. Attach aSmall Guide Spacer (18), a LargeGuide
Spacer (17), and two Bar Guides (15) to the
Upright (2) with an M10 x 152mm Bolt(86).
Pull the upper cable (A) up between the Bar
Guides (15). Press the metal cover on the cable
into the groove in the BlockSpacer (16). Attach a
Small Guide Spacer (18), the Block Spacer, the
two Bar Guides (15), an M10 Thick Washer (54),
and the two Tethers (70) to the Upright (2) with
another M10 x 152mm Bolt (86). Do not tighten
the Bolt yet.
15
16
17
18
114
f
114
68
14
2
81
_43
81
17 ._
18 86
Metal 54
7O
18 16 Groove
43
86
t0