Weinmann MEDUMAT Standard 2 Technical specifications

Changing the ventilation mode
Requirements:
• The device is switched on.
• A ventilation mode is set.
1. Briefly press the menu button .
2. Select the Mode field.
3. Select a ventilation mode.
4. Adjust the ventilation parameters and press start.
Ventilating the patient
Selecting emergency mode
1. Briefly press the On/Off button .
2. Select emergency mode:
• Emergency Pediatric
• Emergency Child
• Emergency Adult
Selecting previous patient
1. Briefly press the On/Off button .
2. Select Previous patient field.
RSI mode
Performing RSI ventilation
Requirements:
• The device is switched on.
• The MEDUtrigger is connected to the device.
• RSI was set as the ventilation mode for a
new patient. The Demand function is
automatically activated.
1. For the function Manual, navigate to the
field Demand.
2. Select the Manual field.
3. To perform continuous ventilation
following successful airway management,
select the Contin. field. The device
switches to IPPV mode.
Selecting a new patient
1. Briefly press the On/Off button .
2. Select New patient field.
3. Select height and gender or navigate to the
Height field and turn the navigation knob further
to select the desired patient group.
4. Press the navigation knob next.
5. Select a ventilation mode.
6. If necessary: Adjust the ventilation parameters and
press start.
Pausing the ventilation
Requirements:
• Cardiac rhythm analysis or defibrillation
is being performed.
• The device is switched on.
• The CPR mode is set.
• Continuous ventilation
is activated.
1. Select the Pause field.
The ventilation is paused for 50 seconds.
CPR mode
Performing CPR ventilation
Requirements:
• The device is switched on.
• The MEDUtrigger is connected to the device.
• A ventilation mode for a new patient is set.
1. Briefly press the CPR button .
The device switches to the mode CPR 30:2/CPR 15:2/CPR IPPV (depending on
the preset). The green LEDs on the MEDUtrigger light up.
2. If necessary:
Change algorithm:
• 30:2
• 15:2
• Continuous
3. Press and hold the MEDUtrigger button
during the ventilation phase until two
mechanical breaths are performed.
4. To exit the CPR mode,
press the CPR button again.
To enable the selection of the function Manual, a MEDUtrigger must
be connected. Otherwise, this function will not be displayed.
If you do not select a menu within 20 seconds, the device automati-
cally switches to the Previous patient menu and immediately begins
ventilation of the patient. In this case, the device uses the ventilation mode
and ventilation parameters set for the last patient to be ventilated. To switch
off the countdown before the 20 seconds have elapsed, move one of the
navigation knobs.
MEDUMAT Standard2MEDUMAT Standard2

Brief operating instructions
MEDUMAT Standard2
Charging the battery
Charging the battery in the device
1. Slide battery into the battery compartment until it clicks into place.
2. Insert the portable system into the wall mounting or connect the device to the
line power via the power supply.
Charging the battery in the charging station
1. Slide the battery into the charging station until it audibly clicks into place.
2. Connect the charging station supply to the line power.
Switching the device on/off
Switching on the device
Requirements:
• The device is disconnected from the patient.
• A fully charged battery is inserted in the device.
• The device is connected to the oxygen supply.
1. Briefly press the On/Off button .
Switching off the device
1. Press and hold the On/Off button for > 2 s.
Performing a function check
Requirements:
• The device is disconnected from the patient.
• A charged battery is inserted in the device.
• The device input filter is inserted in the device.
• A patient hose system and a testing bag are available and ready for use.
• The protective cap has been removed from the end of the patient hose
system.
• A filled oxygen cylinder is available.
1. Check the device, plug, and cable for external damage.
If necessary: Replace components.
2. Briefly press the On/Off button .
3. Briefly press the menu button .
4. Select Function check in the start menu.
5. Follow the instructions in the function check.
Compressed gas
connection
Display
SD card Navigation knobs
Menu
button
Battery
Device
input filter
Connection for
ventilation hose
Line power/battery
status indicator
Alarm light
This document does not replace the instructions for use.
Complete information can be found in the instructions for use.
Battery status indicator
Device Battery Meaning
Battery status > 90%
Battery status approx. 60%-90%
Battery status approx. 40%-60%
Battery status approx. 10%-40%
Battery status < 10%
Battery is almost empty.
Battery is being charged.
Battery is defective, not inserted, or not at
the suitable temperature.
On/Off button
Line power/battery status indicator
Steady green light: Device connected to line power.
No light: Device in NVG mode.
Steady green light: The battery is full or is not being charged
because it is outside the charging
temperature range.
Flashing green light: The battery is being charged.
Steady red light: The battery is defective or not in the device.
No light: The device is operating on battery power and
not on line power or the device is in NVG mode.
Made in GermanySimply Professional
WM 68051b - 10/2015
WEINMANN Emergency
Medical Technology GmbH + Co. KG
Frohbösestraße 12 • 22525 Hamburg • GERMANY
T: [phone] • F: [phone]
E: [email protected]
weinmann-emergency.de
MEDUMAT Standard2