weintek cMT-FHDX User manual

0
User
Manual
cMT-FHDX Startup Guide

cMT-FHDX User Manual
Table of Contents
1 Specification...................................................................................................................................1
1.1 Dimensions.........................................................................................................................2
1.2 Connector pin designations ...............................................................................................3
1.3 USB Host port.....................................................................................................................3
1.4 Ethernet port......................................................................................................................3
1.5 DIP switch...........................................................................................................................3
1.6 LED indicator ......................................................................................................................4
1.7 Battery................................................................................................................................4
1.8 Power connection ..............................................................................................................4
1.9 HDMI Output......................................................................................................................5
2 System Settings ..............................................................................................................................7
2.1 System Toolbar...................................................................................................................7
2.2 System Information............................................................................................................7
2.3 OS Upgrade ......................................................................................................................12

cMT-FHDX User Manual
UM021004E_20210513
1
1Specification
Features
Full HD 1080p High Resolution HDMITM Output
Quad-core Cortex-A17 CPU with High Performance
dedicated 3D Processor
Plays video in high resolution, video decode 1080p
H.264
Supports customized resolution for 16:9 / 4:3 LCD
monitor.
Compact Design and DIN-rail Mountable
Fan-less Cooling System
Built- in 4GB Flash Memory and RTC
One USB Host Port
Gigabit Ethernet Port
Supports MPI 187.5K
Built-in Power Isolator
Memory
Flash
4 GB
RAM
1 GB
Processor
Quad-core 32-bit RISC 1.6GHz
I/O Port
SD Card Slot
N/A
USB Host
USB 2.0 x 1
USB Client
N/A
Ethernet
LAN 1: 10/100/1000 Base-T x 1
LAN 2: 10/100 Base-T x 1
COM Port
COM1: RS-232
COM2: RS-485 2W/4W
COM3: RS-485 2W
RS-485 Dual Isolation
N/A
CAN Bus
N/A
HDMI Output
Customizable (max. resolution 1920 x 1080)
Recommended Resolutions
(Please use these recommended screen
resolutions to avoid compatibility issues.)
720x480, 720x576, 800x600, 1024x768, 1280x720, 1366x768,
1920x1080
Audio Output
HDMI Audio Output
Video Input
N/A
RTC
Built-in
Power
Input Power
24±20%VDC
Power Isolation
Built-in
Power Consumption
850mA@24VDC
Voltage Resistance
500VAC (1 min.)
Isolation Resistance
Exceed 50Mat 500VDC
Vibration Endurance
10 to 25Hz (X, Y, Z direction 2G 30 minutes)
Specification
PCB Coating
Yes
Enclosure
Plastic
Dimensions WxHxD
29.8 x 130 x 115 mm
Weight
Approx. 0.24 kg
Mount
35mm DIN rail mounting
Environment
Protection Structure
IP20
Storage Temperature
-20°~ 60°C (-4°~ 140°F)
Operating Temperature
0°~ 50°C (32°~ 122°F)
Relative Humidity
10% ~ 90% (non-condensing)
Certificate
CE
CE marked
UL
cULus Listed
Software
EasyBuilder Pro V6.04.02 or later versions
EasyAccess 2.0 (Optional)
CODESYS®(Optional)*
* The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing
Administrator, Inc.
* CODESYS®is a trademark of 3S-Smart Software Solutions GmbH.

cMT-FHDX User Manual
UM021004E_20210513
2
Dimensions
1.1
a
USB Host Port
e
Power Connector
b
LAN 2
f
HDMI Port
c
LAN 1
g
DIP Switch
d
COM1: RS-232,
COM2: RS-485 2W/4W,
COM3: RS-485 2W
h
Reset Button
Front View Side View
Top View Bottom View
英文版 簡中版 日文版
正面図 側面図
上面図 下面図
130mm [5.11"]
115mm [4.52"]
29.8mm [1.17"]
125mm [4.92"]
a
b
c
d
e
f
g
h
130mm [5.11"]
115mm [4.52"]
29.8mm [1.17"]
125mm [4.92"]
a
b
c
d
e
f
g
h
130mm [5.11"]
115mm [4.52"]
29.8mm [1.17"]
125mm [4.92"]
a
b
c
d
e
f
g
h

cMT-FHDX User Manual
UM021004E_20210513
3
Connector pin designations
1.2
PIN#
COM1 RS-232
COM2 RS-485
COM3 RS-485
2W
2W
4W
1
Data+
2
RxD
3
TxD
4
Data-
5
GND
6
Data+
RX+
7
Data-
RX-
8
TX+
9
TX-
USB Host port1.3
USB 2.0 full speed host interface supports USB mouse devices, keyboards, printers, barcode
scanners, and USB disks. While using an external hard drive, please use an external power supply.
Do not use USB port to charge external devices.
Ethernet port1.4
The unit has one 10/100/1G Ethernet port and one 10/100 Ethernet port.
The LED indicators on the Ethernet ports indicate:
Orange LED: LAN link status
Green LED: Active status
DIP switch1.5
Each HMI is equipped with a reset button and a set of DIP switches. When using DIP switches to
change modes, the corresponding functions will be triggered.
SW1
SW2
Mode
OFF
OFF
Normal mode
ON
OFF
Hide HMI System Setting Bar
OFF
ON
Update OS
ON
ON
Restore factory default
Note: Reboot HMI after adjusting DIP switches to enter the corresponding mode.

cMT-FHDX User Manual
UM021004E_20210513
4
LED indicator
1.6
LED indicators show the operation status of HMI.
Power (Orange)
Indicates power status.
CPU (Green)
Indicates CPU status.
Communication (Blue)
Indicates communication status, blinks during
communication. When communication is good, it may stay
on.
Battery1.7
cMT-FHDX requires a coin type lithium battery CR1220 to keep the RTC running.
Power connection1.8
Power: The unit can be powered by DC power only, voltage range: 24±20% Volts DC, compatible
with most controller DC systems. The power conditioning circuitry inside the unit is accomplished
by a switching power supply. The peak starting current can be as high as 2A.
Connection: To make a connection, use AWG24~12 wires and insulated terminals. Turn the
connector screw counterclockwise until the gap is wide open, insert the wire all the way in, and turn
the screw clockwise until it is tight.
Note: Connect positive DC line to the ‘+’terminal and the DC ground to the‘-’terminal.

cMT-FHDX User Manual
UM021004E_20210513
5
HDMI Output
1.9
Supports 1920 × 1080 high resolution HDMI output. Displays image via HDMI or DVI interface LED /
LCD.
Note: When cMT-FHDX enters backlight saver mode, an external keyboard or mouse is needed for
turning on the backlight.
The following shows how cMT-FHDX’s HDMI connector can be used.
1. Connect to DVI monitor.
Use HDMI-to-DVI converter to connect the monitor.
Note: cMT-FHDX supports resolution 1920x1080p, please use DVI monitor / converter.
2. Directly connect to HDMI monitor.

cMT-FHDX User Manual
UM021004E_20210513
6
3. Use HDMI splitter to connect multiple HDMI monitors.
4. Use HDMI switch to connect two cMT-FHDX with one HDMI monitor.
Note: If not connecting a repeater, the maximum length of HDMI cable allowed is 15m. To reach a
longer distance, please use CAT6 cable or a repeater. HDMI converter is used to detect the monitor
and correctly output.

cMT-FHDX User Manual
UM021004E_20210513
7
2System Settings
For the first time operating the unit, please complete the following system settings. When finished,
the project files designed using EasyBuilder can be used on cMT-FHDX.
2.1 System Toolbar
After rebooting cMT-FHDX, the Setting window can be opened by tapping the round start button on
the screen (video output by HDMI).
How to hide HMI System Setting Bar
When [DIP Switch 1] is set ON, the system setting bar is hidden; when set OFF; the system setting
bar is shown. Please reboot HMI for the DIP switch setting to take effect.
System register [LB-9020] can also be used to show/hide system setting bar.
When [LB-9020] is set ON, the system setting bar is shown, and when the register is set OFF, the
system setting bar is hidden.
2.2 System Information
For safety, please set a password to protect HMI parameters from being modified by an
unauthorized party. By default, the password is 111111.
CODESYS
Enter the activation code to activate
CODESYS.

cMT-FHDX User Manual
UM021004E_20210513
8
General
General settings including FTP settings.
[Direction]
Set screen orientation mode to landscape
or portrait by selecting degrees from 0 / 90
/ 180 / 270.
[Brightness]
Adjust screen brightness.
[Volume]
Adjust volume of HDMI sound output. The
monitor used must support DDC/CI.
[Popup download window]
When enabled, the download window can
pop up.
[FTP Port]
Select an FTP port.
[FTP client can modify USB/SD data]
When enabled, an FTP client can change
the data in the external device connected
to HMI.
[Show Start button]
When enabled, the Start button is shown.
Network
Download project file to HMI via Ethernet.
The IP address of the target device (HMI)
must be correctly set. Users can choose
from obtaining an IP address automatically
or entering an IP address manually. To use
Email or EasyAccess 2.0, please set DNS
correctly. ETH1 and ETH2 must use
different domains. When CODESYS is
activated, HMI can only use ETH2.