weintek cMT-FHDX User manual

User
Manual
cMT-FHDX Startup Guide
Weintek USA, Inc.
www.WeintekUSA.com
[phone]
Rev. 24 SEP, 2020
The terms FHDXI, FHDXI High-Definition Multimedia Interface, and the FHDXI Logo are
trademarks or registered trademarks of FHDXI LicensingAdministrator, Inc.

Table of Contents
1. Supported Touch Screen………………………………………………………………………………………………………… 3
2. Network Wiring Diagram………………………………………………………………………………………………………… 4
3. Setup……………............................................................................................................................. 5
4. Web Interface....................................................................................................……………………… 18
5. How to Use WebView………………………………………………………………………………………………………………. 26
6. How to Load a Project via USB Drive ......................................................................................... 28
7. How to Retrieve Historical Data via USB Drive........................................................................... 29
8. How to Delete All Historical Data............................................................................................... 30
9. OS Upgrade................................................................................................................................ 31
10. How to Calibrate Resistive Touch Screen……………………………………………………………………………….. 33
11. How to Adjust the Resolution of cMT-FHDX……………………………………………………………………………. 35
12. cMT-Viewer.…………………………………………………………………………………………………………………………… 36
13. Monitor Mode………………………………………………………………………………………………………………………… 44
14. cMT-Viewer Limitations………………………………………………………………………………………………………….. 48
15. cMT-FHDX Gestures Operation………………………………………………………………………………………………… 50
16. cMT-iM21 Touch Screen………………………………………………………………………………………………………… 51

1. Supported Touch Screen
The following industrial touch screens are verified to be compatible with the cMT-FHDX.
Brand
Name
Model
Touch Screen Type
Screen
Size
(Inch)
Requires OS
Version
IEI
DM-F22A/PC-R11
USB projected
capacitive touch
21.5"
20171208 or
greater
Aplex
ARCDIS-121AP
USB projected
capacitive touch
21.5"
20171208 or
greater
Indumicro
IMD-C220PT
USB projected
capacitive touch
21.5"
20171208 or
greater
Hope
Industrial
Systems
HIS-ML19.5-CTBA
USB analog resistive
touch
19.5"
20180523 or
greater
ELO
ET1590L-7CWB-1-ST-NPB-G
USB AccuTouch® 5-
wire Resistive Touch
15"
20180523 or
greater
ELO
ET1593L-2UWB-0-MT-ZB-NPB-G
TouchPro PCAP
15.6"
20180523 or
greater
ELO
ET2094L-8CWB-0-ST-NPB-G
USB IntelliTouch
19.5"
20180523 or
greater
Cincoze
CV-117R/M1001
USB Resistive Touch
17"
20180910 or
greater
Weintek
cMT-iM21
Capacitive touch
21.5"
20171208 or
greater

2. Network Wiring Diagram
Connect a cMT-FHDX to a router by an Ethernet cable as the diagram shows below.
The default IP address of LAN 1 is DHCP. The default IP address of LAN 2 is static IP 192.168.100.1. The
IP addresses of LAN 1 and LAN 2 must be configured to different subnets, except for the cMT-FHDX
which have been activated with a Codesys license.
cMT-FHDX LAN Ports:
The cMT-FHDX is equipped with two independent Ethernet ports which isolate the device network
from the company/factory network. LAN1 is a WAN (Wide Area Network) port which is allowed to
connect to a public network or another network via a gateway. LAN2 is a LAN (Local Area Network)
port.

5
3. Setup
Press the system toolbar button in the top left of the screen to open the Setup menu.
Information
This page shows general information about cMT-FHDX and network information.

6
General
Adjust the brightness of the screen and audio volume. The Audio option will be available when the
connected monitor display supports DDC /CI (Display Data Channel/Command Interface).
Language
Select a language for Setup. The language selected on the project of the cMT-FHDX won’t be
changed by this setting.

7
Input Method
Select languages for system keyboard input use.

8
Advanced Settings
To access more system settings, click on the lock icon in the top left corner. There are two different levels of
password protection. Select [System Setting] and enter System Setting password. The default password of
System Setting is 111111. The Codesys tab, OS Upgrade tab, and Reset Option tab will be accessible to
System Setting.
After clicking on [OK], the icon will become unlocked.
Codesys
This is a page used to activate Codesys functionality. To activate this feature on a cMT-FHDX, a Codesys
activation card is required and must be purchased separately.
[Codesys Activation Code]- Enter the codes displayed on a Codesys activation card. Click [Active] to activate
Codesys.
Note: Once Codesys is activated, there is no way to remove Codesys from the cMT-FHDX.
[Restore Codesys License]- The Codesys functionality will be restored if it is enabled. Contact Weintek USA
before using this.

9
General
[Direction]- Click on the button to change the direction of the screen display.
[Popup download window]- If enabled, after inserting a USB drive to the USB port of the cMT-FHDX, the
Upload/Download dialog window will pop up.
[FTP Port]- Click the “>”button to change FTP port number.
[FTP client can modify USB/SD data]- If enabled, historical data stored in USB drive can be modified via
FTP(File Transfer Protocol).
[Show Start button]- If this option is turned off, the system toolbar button will be hidden.

10
Network
Set the IP addresses of Ethernet 1 and Ethernet 2. The default IP address of Ethernet 1 is DHCP. The default
IP address of Ethernet 2 is 192.168.100.1. The IP addresses of Ethernet 1 and Ethernet 2 must be on
separate subnets, except for the cMT-FHDX with activated Codesys.
Click on one of the “>”button. Enable [Obtain an IP address automatically] (DHCP) or set the IP address
manually (Static IP).

11
Time/Date
Adjust cMT-FHDX RTC manually.
HMI Name
Change the name of cMT-FHDX to identify this HMI when retrieving historical data or loading a project on a
PC. This saves time remembering the IP address of each cMT-FHDX.

12
Clear History
This page is used to clear historical data, recipe, and database information stored in the internal memory of
cMT-FHDX.
Project Management
Restarts the project of the cMT-FHDX and restores it to its initial state without cycling power.

13
System Password
There are three different levels of password protection, User, Update Project, and System Setting.
This page is used to change the passwords for operating a project via cMT viewer, loading a project to the
HMI, accessing FTP server and so on. The default passwords of the three levels are 111111.
[User]- This level can operate cMT projects via cMT viewer.
[Update project]- This level can load and retrieve the HMI project, as well as retrieve historical data, such as
data sampling and event log data. In addition, it can operate cMT projects via cMT viewer.
[System Setting]- This level has access to all system settings, load and retrieve the project, retrieve historical
data, and operate cMT projects via cMT viewer. It is the highest security level.
[History]- FTP server access. The default password is 111111.
Password hierarchy -
System
setting -for
administrator
Update project-
for supervisors
User- for operators

14
Enhanced Security (Objects authorized to operators in HMI project)
This function provides user passwords and security classes to prevent unauthorized operators from
accessing objects that have the potential to cause damage or injury within your cMT-FHDX project. For
more information, refer to section 5.6.2 Enhanced Security Mode in the Easybuilder pro user manual.
VNC Setting
The VNC server provides remote HMI monitoring and controlling via Ethernet connection.
[Start VNC]- It allows VNC connection with only one VNC client.
[VNC multi connection]- It allows connection with multiple VNC clients. Connecting the VNC server to too
many VNC clients may slow down the communication speed and HMI performance.
[VNC login password]- Specify a password. Logging in the VNC server will require the password.

15
EasyAccess2.0
EasyAccess 2.0 is a tool that allows users to access and control a cMT-FHDX remotely from anywhere in the
world. cMT-FHDX isNOTa pre-licensed model. To use this feature, an EasyAccess 2.0 activation card is
required and must be purchased separately.
For more information, refer to EasyAccess2.0 user manual.
Printer
cMT-FHDX can search your intranet for a network printer and connect to the printer.
Click [Install network printer] and select a printer from the list.

16
[URI]- Device URI (Uniform Resource Identifier).
[Backup PPD file]- It is used to copy the PPD file (PostScript Printer Description) of printer.
OS Upgrade
This page is used to upgrade the OS version of cMT-FHDX.

17
Reset Options
This page is used to reset a cMT-FHDX to its factory default settings. Press [Start] to reset if needed.
Enter “yes”into the box and click on [OK] to start reset process.

18
4. Web Interface
A cMT-FHDX’s setting can also be accessed via a web browser. Before configuration, connect cMT-
FHDX(LAN1) to a router via an Ethernet cable. Open a web browser (Edge, Chrome, or Firefox) and enter the
IP address of the cMT-FHDX. For example, enter 192.168.1.15.
Select an identity and enter its password.
The tabs of the web interface are displayed as shown. They are System, Network, Project, Data, Features,
and Account.

19
Feature Introduction
Info
[Now] - Synchronizes the HMI RTC with the PC RTC.
Project Management
[Restart Project] - Restarts cMT-FHDX and restores it to its initial state.
[Update Project]- Loads a project and recipes from the PC to cMT-FHDX.
[Backup Project]- Uploads a project from cMT-FHDX to the PC.
[USB/SD Update]- Loads a project via a USB drive plugged into the USB slot of cMT-FHDX. Select the
*.cxob file and click [Update].

20
Email
This page provides setup of the SMTP server and email contact lists. For more information, refer to section
5.11 e-Mail in the Easybuilder pro user manual.
Recipe
[Update]- Select a button to transfer recipe files from the PC to the cMT-FHDX.
[Backup] - Select a button to transfer recipe files from the cMT-FHDX to the PC.
[Clear]- It is used to clear recipe and database information stored in the cMT-FHDX.