Wells SS10 Series User manual

WELLS
R A I S I N G T H E S T A N D A R D
Specifications
Overall Dimensions: Inches MM
Diameter
SS-4 series 8 1/4 210
SS-8 series 10 1/16 256
SS-10 series 12 305
Height
SS-4 series 9 1/4 235
SS-8 series 8 3/8 213
SS-10 series 8 3/8 213
Temperature Settings: OFF/LO to HI
Weights: Lbs. KG
SS-4 series
Installed 4 2
Shipping 5 2
SS-8 series
Installed 5 2
Shipping 6 3
SS-10 series
Installed 6 3
Shipping 7 3
SS-10
SS-8
SS-4, SS-8, SS-10 BUILT-IN
ROUND FOOD WARMERS
SS-4, SS-8, SS-10 BUILT-IN ROUND FOOD WARMERS
I T E M N O .
WE L L S M A N U F A C T U R I N G
Features
• The tubular element, located under the warming pan,
allows for quick and efficient heating.
• Infinite control is housed in a remote, oval
panel with a guard ring to help prevent accidental
temperature changes.
• Warmers have a high-limit thermostat, which
prevents unit overheating.
• Models are available with optional ” drain (D).
• Warmers are designed for wet or dry operation.
• Wellslok allows for quick and easy installation in
stainless steel countertops.
• The SS-4, SS-8 and SS-10 Warmers are
Underwriters Laboratories, Inc. Recognized and
meet NSF International and Canadian standards.
• A one-year warranty against defects covers parts
and labor.
Accessories / Options
Adapter Top, to convert SS-8 to hold one
4-quart inset, 20177
Adapter Top, to convert SS-10 to hold one
4-quart inset, 20822
Adapter Top, to convert SS-10 to hold one
7-quart inset, 20175
Inset, 4-quart capacity with lid, 20774
Inset, 7-quart capacity with lid, 20587
Inset, 11-quart capacity with hinged lid, 21057
Optional Drain (D) is available
Drain Valve Extension Kit, extension from drain
to counter front with remote handle, (D) models
only, 20385
Wells SS-4, SS-8 and SS-10 Built-In Round Food
Warmers have stainless steel, deep-drawn warming
pans and are suitable for wet or dry operation.
These warmers are designed for installation into
a metal counter and come in a variety of sizes to
fit your needs.

WELLS
SS-4, SS-8, SS-10 ELECTRICAL SPECIFICATIONS:
MODELS VOLTS WATTS AMPS PHASE POWER SUPPLY CORD
WELLS MANUFACTURING COMPANY
2 ERIK CIRCLE, PO BOX 280, VERDI, NV 89439 U.S.A. • USA PHONE: [phone] • FAX: [phone]
FOR ORDERS ONLY: [phone] • FAX: [phone] • www.wellsbloomfield.com
2001 WELLS MANUFACTURING • PRINTED IN THE U.S.A. • 2/01 • REV(L) • PART NO. 37122
MODELS
SS-4, SS-8, SS-10
B U I LT- I N R O U N D
F O O D WA R M E R S
(25)
1
(216)
8 1/2
(184)
7 1/4
(241)
9 1/2
(210)
8 1/4
(113)
4 7/16
(22)
7/8
(222)
8 3/4
(256)
10 1/16
(305)
12
SS-4, 8
MODELS
MODELS
SS-10
(D MODELS ONLY)
1/2 NPT
SS-4
MODELS
SS-8
MODELS
SS-10
MODELS
MODELS
SS-4
MODELS
SS-8,10
DIMENSIONS: INCH
(MM)
WE L L S M A N U F A C T U R I N G
SUGGESTED CLEARANCE FROM
UNIT TO THE NEAREST SURFACE
BACK SIDE BOTTOM FRONT*
1 1 8 1/2 4
(25) (25) (216) (102 )
R
STD.4
R
E6070
COMPONENT
R
E6070
SS-4, 8, 10 120 450 3.8 SINGLE NONE
SS-4, 8, 10 208 338 1.6 SINGLE NONE
SS-4, 8, 10 240 450 1.9 SINGLE NONE
NOTE: Specifications are subject to change without notice. See installation instructions prior to installing the unit.
This document is not for installation purposes. The installation of recognized component units requires additional
evaluations to Underwriters Laboratories, Inc. standards.
THIS UNIT IS DESIGNED TO BE INSTALLED IN METAL COUNTERS ONLY.
All models with a ‘D’ suffix have the same electrical specifications as the standard models.
* When control box is located below the unit,
front clearance can be 2 inches.
NOTE: Depending on the installation,
clearances can be reduced upon further
evaluations to UL standards.