Wells SS-10T User manual

WELLS
R A I S I N G T H E S T A N D A R D
Specifications
Overall Dimensions: Inches MM
Diameter
SS-8T series 10 1/16 256
SS-10T series 12 305
Height
SS-8T series 8 3/8 213
SS-10T series 8 3/8 213
Temperature Settings: OFF/LO to HI
Weights: Lbs. KG
SS-8T series
Installed 5 2
Shipping 6 3
SS-10T series
Installed 6 3
Shipping 7 3
SS-8T SS-10T
SS-8T, SS-10T BUILT-IN
ROUND FOOD WARMERS
SS-8T, SS-10T BUILT-IN ROUND FOOD WARMERS
I T E M N O .
WE L L S M A N U F A C T U R I N G
Features
• The tubular element, located under the warming
pan, allows for quick and efficient heating.
• Positive-off thermostat controls the
element, allowing for adjustable and more
consistent temperatures.
• Control is provided with an oval panel with
protective guard ring to prevent accidental
temperature changes.
• Models are available with an optional ” drain (D).
• Warmers are designed for either wet or
dry operation.
• Wellslok allows for quick and easy installation in
stainless steel countertops.
• The SS-8T and SS-10T Warmers are Underwriters
Laboratories, Inc. RECOGNIZED and meet NSF
International and Canadian standards.
• A one-year warranty against defects covers
parts and labor.
Accessories / Options
Adapter Top, to convert SS-8T to hold one
4-quart inset, 20177
Adapter Top, to convert SS-10T to hold one
4-quart inset, 20822
Adapter Top, to convert SS-10T to hold one
7-quart inset, 20175
Inset, 4-quart capacity with lid, 20774
Inset, 7-quart capacity with lid, 20587
Inset, 11-quart capacity with hinged lid, 21057
Optional Drain (D) is available
Drain Valve Extension Kit, extension from
drain to counter front with remote handle,
(D) models only, 20385
Wells SS-8T and SS-10T Built-In Round Food
Warmers have stainless steel, deep-drawn warming
pans and are suitable for either wet or dry operation.
These warmers are designed for installation into a
metal counter only and can adapt to a variety of sizes
to fit your needs.

WELLS
S S - 8 T, S S - 1 0 T E L E C T R I C A L S P E C I F I C AT I O N S :
MODELS VOLTS WATTS AMPS PHASE POWER SUPPLY CORD
R
STD.4
R
E6070
COMPONENT
R
E6070
(256)
12
(256)
10 1/16
(216)
8 1/2
(184)
7 1/4
(222)
8 3/4
(113)
4 7/16
SS-10
MODELS
MODELS
SS-8
MODELS MODELS
SS-10SS-8
(TD MODELS)
1/2 NPT
WELLS MANUFACTURING COMPANY
2 ERIK CIRCLE, PO BOX 280, VERDI, NV 89439 U.S.A. • USA PHONE: [phone] • FAX: [phone]
FOR ORDERS ONLY: [phone] • FAX: [phone] • www.wellsbloomfield.com
© 2001 WELLS MANUFACTU RING • PRINTED IN THE U.S.A. • 04/01 • REV(H) • PART NO. 41941
MODELS
SS-8T, SS-10T
B U I LT- I N R O U N D
F O O D WA R M E R S
DIMENSIONS: INCH
(MM)
WE L L S M A N U F A C T U R I N G
SUGGESTED CLEARANCE FROM
UNIT TO THE NEAREST SURFACE
BACK SIDE BOTTOM FRONT*
1 1 8 1/2 4
(25) (25) (216) (102 )
SS-8, 10T 120 825 6.9 SINGLE NONE
SS-8, 10T 208 620 3.0 SINGLE NONE
SS-8, 10T 240 825 3.4 SINGLE NONE
NOTE: Specifications are subject to change without notice. See installation instructions prior to installing the unit.
This document is not for installation purposes. The installation of recognized component units requires additional
evaluations to Underwriters Laboratories, Inc. standards.
THIS UNIT IS DESIGNED TO BE INSTALLED IN METAL COUNTERS ONLY.
All models with a 'D' suffix have the same electrical specifications as the standard units.
* When control box is located below the unit,
front clearance can be 2 inches.
NOTE: Depending on the installation,
clearances can be reduced upon further
evaluations to UL standards.