Weslo Momentum 220X WLEL2006.0 User manual

CAUTION
Read all precautions and
instructions in this manual
before using this equipment.
Keep this manual for future
reference.
Model No. WLEL2006.0
Serial No.
Serial
Number
Decal
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
USER'S MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-866-699-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
(closed on holidays)
ON THE WEB:
www.wesloservice.com

2
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WESLO is a registered trademark of ICON IP, Inc.

3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical exerciser.
1. Read all instructions in this manual and all
warnings on the elliptical exerciser before
using the elliptical exerciser.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. The elliptical exerciser is intended for
home use only. Do not use the elliptical
exerciser in a commercial, rental, or institu-
tional setting.
4. Keep the elliptical exerciser indoors, away
from moisture and dust. Place the elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around the elliptical exerciser to mount, dis-
mount, and use it.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. Keep children under 12 and pets away from
the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 250 pounds.
8. Wear appropriate exercise clothes while
using the elliptical exerciser. Always wear
athletic shoes for foot protection while exer-
cising.
9. When mounting and dismounting the ellipti-
cal exerciser, always hold the upper body
arms and step onto and off the pedal that is
in the lowest position.
10. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
11. Keep your back straight when using the ellip-
tical exerciser; do not arch your back.
12. If you feel pain or dizziness while exercising,
stop immediately and cool down.
13. When you stop exercising, allow the pedals
to slowly come to a stop.
14. The warning decal shown on page 4 has
been applied to the elliptical exerciser. If the
decal is missing or illegible, call the toll-free
telephone number on the front cover of this
manual and order a free replacement decal.
Apply the decal in the location shown.
WARNING: Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.

4
BEFORE YOU BEGIN
Thank you for selecting the new WESLO®Momentum
220X elliptical exerciser. The Momentum 220X is an
incredibly smooth exerciser that moves your feet in a
natural elliptical path, minimizing the impact on your
knees and ankles. Welcome to a whole new world of
natural, elliptical-motion exercise.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
cover of this manual. To help us assist you, note the
product model number and serial number before con-
tacting us. The model number is WLEL2006.0. The
serial number can be found on a decal attached to the
elliptical exerciser (see the front cover of this manual).
To avoid a registration fee for any service needed
under warranty, you must register the elliptical
exerciser at www.wesloservice.com/registration.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
FRONT
BACK
RIGHT SIDE
Pedal Arm
Pedal Disk
Side Shield
Pedal
Upright
Water Bottle Holder
(no bottle is included)
Console
Upper Body Arm
Wheel
Handgrip Pulse Sensor

5
M8 Split
Washer (79)–4
M8 Washer
(64)–4
M10 Split
Washer (78)–4
M4 x 16mm
Screw (60)–4
M8 x 25mm Patch
Screw (70)–2
M8 x 19mm Patch
Screw (73)–4
M8 Nylon
Locknut (59)–6
M10 Nylon
Locknut (84)–4
M8 x 23mm Button
Screw (65)–4
Large Wave
Washer (20)–4
Wave Washer
(27)–2
M4 x 19mm
Screw (68)–6
M8 Large
Washer (81)–2
Star Washer
(85)–6
M10 x 76mm Button Bolt (74)–2M10 x 60mm Button Screw (67)–2
M10 x 75mm Carriage Bolt (58)–2
M4 x 22mm
Screw (66)–2
M8 x 45mm Button
Bolt (11)–4
ASSEMBLY
To hire an authorized service technician to assemble the elliptical exerciser, call toll-free 1-800-445-2480.
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the
included hex keys, assembly requires a phillips screwdriver , an adjustable
wrench , and a rubber mallet .
See the drawings below to identify the small parts needed for assembly. The number in parentheses below
each drawing is the key number of the part, from the PART LIST on page 17. The number following the key
number is the quantity needed for assembly. Note: Some small parts may have been preassembled. If a part
is not in the parts bag, check to see if it has been preassembled.

6
1.
Attach the Rear Stabilizer (35) to the Frame (1) with
two M10 x 75mm Carriage Bolts (58) and two M10
Nylon Locknuts (84).
Press the Stabilizer Endcaps (36) onto the Rear
Stabilizer (35) as shown.
2. Attach the Front Stabilizer (3) to the Frame (1) with
two M10 x 76mm Button Bolts (74), two M10 Split
Washers (78), two Concave Spacers (13), and two
M10 Nylon Locknuts (84). Do not tighten the
Nylon Locknuts yet.
Thread two M10 x 60mm Button Screws (67) with
two M10 Split Washers (78) and two Concave
Spacers (13) through the Front Stabilizer (3) and
into the Frame (1). Tighten the two M10 Nylon
Locknuts (84), and then tighten the Button
Screws.
Orient a Wheel (28) so the four posts (see the inset
drawing) are facing away from the Front Stabilizer
(3). Attach the Wheel to the Front Stabilizer with an
M8 Nylon Locknut (59). Next, press a Wheel Cover
(29) onto the posts on the Wheel. Attach the other
Wheel (not shown) in the same way.
84
35
1
36
36
3. While another person holds the Upright (2) near the
Frame (1), connect the Upper Wire Harness (18) to
the Lower Wire Harness (38).
Carefully slide the Upright (2) onto the Frame (1).
Be careful to avoid pinching the Wire Harnesses
(18, 38). Attach the Upright with four M8 x 19mm
Patch Screws (73) and four M8 Split Washers (79).
Do not tighten the Patch Screws yet.
3273
73
1
73
79
38
18
79
79
58
1
To make assembly easier, read the information
on page 5 before you begin assembling the
elliptical exerciser.
2
28
Posts
84
3
67
13 78 67
28
29
78
59
78
74
78
13
13
1
13

7
5. Apply a generous amount of grease to the Pivot Axle
(16). Then, apply a small amount of grease to two
Wave Washers (27).
While another person aligns the Upper Body Legs (6,
7) with the Upright (2) as shown, insert the Pivot Axle
(16) into the Upper Body Legs and the Upright. Be
careful not to damage the Upper Wire Harness
(18) with the Pivot Axle.
Place a Wave Washer (27) on each end of the Pivot
Axle (16). Then, tighten an M8 x 23mm Button
Screw (65), an M8 Washer (64), and a Pivot Cover
(14) into each end of the Pivot Axle.
5
6. Apply a generous amount of grease to the axle on
the left Upper Body Leg (6). Then, apply grease to a
Large Wave Washer (20) and slide it onto the axle.
Apply a generous amount of grease to the Left
Crank Arm (42). Then, slide a Crank Arm Spacer
(45) onto the Left Crank Arm. Make sure the flat
side of the Crank Arm Spacer is facing away from
the Left Crank Arm.
Slide the Left Pedal Arm (21) onto the left Upper
Body Leg (6) and onto the Left Crank Arm (42).
Repeat this step for the other side of the elliptical
exerciser.
6
6
21
20
Grease
Grease
42
45
14
27
7
2
18
6
65
64
14
64
27
16
Grease
Grease
65
4
4. Identify the Left Pedal Arm (21), which is marked
with a “Left” sticker. Attach a Pedal (19) to the Left
Pedal Arm with three M4 x 19mm Screws (68) and
three Star Washers (85).
Attach the other Pedal (not shown) to the Right
Pedal Arm (not shown) in the same way.
19
21
68
85
85

8
8
9
10
2
18
60 17
66
9. While another person holds the Console (10) near
the Upright (2), connect the Upper Wire Harness
(18) to the wire harness on the Console.
Attach the Console (10) to the Upright (2) with four
M4 x 16mm Screws (60). Be careful not to pinch
the wire harnesses.
Attach the Water Bottle Holder (17) to the Upright
(2) with two M4 x 22mm Screws (66).
8. The Console (10) requires four “AA” batteries (not
included); alkaline batteries are recommended.
Remove the battery cover from the Console. Insert
four batteries into the Console; make sure that the
batteries are oriented as shown by the diagram
inside the battery compartment. Then, reattach
the battery cover. 10
Batteries
Battery
Cover
Wire Harness
73
7. Attach the Left Pedal Arm (21) to the Left Upper
Body Leg (6) with an M8 x 23mm Button Screw
(65), an M8 Washer (64), and a Pedal Leg Cover
(23).
Apply grease to a Large Wave Washer (20) and
slide it onto the Left Crank Arm (42). Then, attach
the Left Pedal Arm (21) to the Left Crank Arm with
an M8 x 25mm Patch Screw (70) and an M8 Large
Washer (81).
Repeat this step for the other side of the elliptical
exerciser.
See step 3. Tighten the four M8 x 19mm Patch
Screws (73).
7
Grease
20
81
70
23
64
21
6
65 42

9
10. Insert the Left Upper Body Arm (4) into the Left
Upper Body Leg (6) and attach it with two M8 x
45mm Button Bolts and two M8 Nylon Locknuts (59).
Make sure that the Nylon Locknuts are in the
hexagonal holes in the Left Upper Body Arm.
Repeat this step for the Right Upper Body Arm (5)
and the Right Upper Body Leg (7).
11. Make sure that all parts of the elliptical exerciser are properly tightened. Place a mat under the elliptical
exerciser to protect the floor or carpet from damage.
10
59
5
7
11
6
4

10
HOW TO USE THE ELLIPTICAL EXERCISER
HOW TO MOVE AND LEVEL THE ELLIPTICAL
EXERCISER
To move the elliptical exerciser, stand in front of it,
place one foot against one of the wheels, and firmly
hold the upper end of the upright. Pull the upright for-
ward until you can move the elliptical exerciser on the
wheels. Carefully move the elliptical exerciser to the
desired location and then lower it. To decrease the
risk of injury, do not attempt to move the elliptical
exerciser over an uneven surface.
If the elliptical exerciser rocks slightly on your floor,
turn one or both of the levelling feet under the front
stabilizer until the rocking motion is eliminated.
HOW TO EXERCISE ON THE ELLIPTICAL
EXERCISER
To mount the elliptical exerciser, firmly hold the upper
body arms and carefully step onto the pedal that is in
the lowest position. Then, step onto the other pedal.
Push the pedals until they begin to move with a con-
tinuous motion. Note: The pedal disks can turn in
either direction. It is recommended that you turn
the pedal disks in the direction shown below;
however, for variety, you can turn the pedal disks
in the opposite direction.
To dismount the elliptical exerciser, allow the pedals
to come to a complete stop. The elliptical exerciser
does not have a freewheel; the pedals will contin-
ue to move until the flywheel stops. When the ped-
als are stationary, step off the highest pedal first.
Then, step off the lower pedal.
Pedal
Pedal
Disk
Upper
Body Arm
Wheel
Upright
Leveling Foot