Weslo 8.25 Elliptical User manual

CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. eep this manual
for future reference.
Model No. WLCCEL2309.0
Serial No.
Write the serial number in the
space above for future reference.
Serial
Number
Decal
QUESTIONS?
If you have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-936-4266
Mon.–Fri., 8:00 until 17:00 ET
(excluding holidays)
OR E-MAIL US:
[e-mail]
USER'S MANUAL
www.weslo.com

2
TABLE OF CONTENTS
WARNINGDECALPLACE ENT ..............................................................2
IPORTANTPRECAUTIONS ................................................................3
BEFOREYOUBEGIN ......................................................................4
ASSE BLY ...............................................................................5
HOWTOUSETHEELLIPTICALEXERCISER ..................................................10
AINTENANCEANDTROUBLESHOOTING ...................................................15
EXERCISEGUIDELINES ...................................................................16
PARTLIST ..............................................................................17
EXPLODEDDRAWING ....................................................................18
ORDERINGREPLACE ENTPARTS ..................................................BackCover
LI ITEDWARRANTY ..............................................................BackCover
WESLO is a registered trademark of ICON IP, Inc.
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning
decal(s). If a decal is missing or illegible, see
the front cover of this manual and request a
free replacement decal. Apply the decal in the
location shown. Note: The decal(s) may not be
shown at actual size.

3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical exerciser before using your elliptical
exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
IMPORTANT PRECAUTIONS
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. The elliptical exerciser is intended for home
use only. Do not use the elliptical exerciser
in a commercial, rental, or institutional set-
ting.
4. eep your elliptical exerciser indoors, away
from moisture and dust. Place your elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is at least 3 ft. (1 m) of
clearance in the front and rear of your ellipti-
cal exerciser and 2 ft. (0.6 m) on each side.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. eep children under age 12 and pets away
from the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 250 lbs.
(113 kg).
8. Wear appropriate exercise clothes while
using the elliptical exerciser; do not wear
loose clothes that could become caught on
the elliptical exerciser. Always wear athletic
shoes for foot protection while exercising.
9. Hold the upper body arms when mounting,
dismounting, or using the elliptical exerciser.
10. eep your back straight while using the ellip-
tical exerciser; do not arch your back.
11. The pulse sensor is not a medical device.
Various factors, including the userʼs move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
12. When you stop exercising, allow the pedals
to slowly come to a stop.
13. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
14. Use the elliptical exerciser only as described
in this manual.

4
BEFORE YOU BEGIN
Thank you for selecting the new WESLO®8.25 ellipti-
cal exerciser. The WESLO 8.25 elliptical exerciser
provides an impressive selection of features designed
to make your workouts at home more effective and
enjoyable.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
cover of this manual. To help us assist you, note the
product model number and serial number before con-
tacting us. The model number and the location of the
serial number decal are shown on the front cover of
this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Pedal Disc
Shield
Pedal
Leveling Foot
Upright
Water Bottle Holder*
*Water bottle is not included
Console
Upper Body Arm
Pulse Sensor
Arm Knob
Wheel

5
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included tools and your own Phillips screwdriver , adjustable
wrench , and rubber mallet .
See the drawings below to identify the small parts needed for assembly. The number in parentheses below
each drawing is the key number of the part, from the PART LIST near the end of this manual. The number fol-
lowing the key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to
see if it has been preassembled.
M8 Split
Washer (79)–4
M8 Washer
(64)–4
M10 Split
Washer (78)–4
M4 x 16mm
Screw (60)–4
Large Wave
Washer (20)–4
M8 x 25mm Patch
Screw (70)–2
M8 x 19mm Patch
Screw (73)–4
M8 Locknut
(59)–2
M10 Locknut
(84)–4
M8 x 23mm Button
Screw (65)–4
Wave Washer
(27)–2
M4 x 19mm
Screw (68)–6
M8 Large
Washer (81)–2
M4 x 32mm
Screw (67)–8
M4 x 12mm Flat
Head Screw (88)–8
Star Washer
(85)–6
M10 x 76mm Button Bolt (74)–2M10 x 60mm Button Screw (89)–2
M10 x 50mm Carriage Bolt (75)–2 M10 x 75mm Carriage Bolt (58)–2
M4 x 22mm
Screw (66)–2
ASSEMBLY

6
1.
Attach the Rear Stabilizer (35) to the Frame (1) with
two 10 x 75mm Carriage Bolts (58) and two 10
Locknuts (84).
Press the Stabilizer Caps (36) onto the Rear
Stabilizer (35) as shown.
2. Attach the Front Stabilizer (3) to the Frame (1) with
two 10 x 76mm Button Bolts (74), two 10 Split
Washers (78), two Concave Spacers (90), and two
10 Locknuts (84). Do not tighten the Locknuts
yet.
Finger-tighten two 10 x 60mm Button Screws (89)
with two 10 Split Washers (78) and two Concave
Spacers (90) into the bottom of the Front Stabilizer (3)
and the Frame (1). Tighten the two M10 Locknuts
(84), and then tighten the Button Screws.
Orient a Wheel (28) so that the four posts (see the
inset drawing) are facing away from the Front
Stabilizer (3). Attach the Wheel to the Front Stabilizer
with an 8 Locknut (59). Then, press a Wheel Cover
(29) onto the posts on the Wheel. Attach the other
Wheel (not shown) in the same way.
84
35
1
84
3
78
78
90
90
89
90
78 89
1
36
36
28
29
74
78
90
59
3. While another person holds the Upright (2) near the
Frame (1), connect the Upper Wire Harness (18) to
the Lower Wire Harness (38).
Tip: Avoid pinching the Wire Harnesses (18, 38).
Carefully slide the Upright (2) onto the Frame (1).
Attach the Upright with four 8 x 19mm Patch
Screws (73) and four 8 Split Washers (79). Do not
tighten the Patch Screws yet.
3
2
73
73
1
73
79
38
18
79
79
58
1
To make assembly easier, read the assembly
tips on page 5 before you begin assembling
the elliptical exerciser.
2
28
Posts

7
4
4. Identify the Left Pedal Arm (21), which is marked with
asticker. Attach a Pedal (19) to the Left Pedal Arm
with three 4 x 19mm Screws (68) and three Star
Washers (85).
Attach the other Pedal (not shown) to the Right
Pedal Arm (not shown) in the same way.
19
21
68
85
85
5. Apply a generous amount of grease to the Pivot Axle
(16). Then, apply a small amount of grease to two
Wave Washers (27).
While another person aligns the Upper Body Legs (6)
with the Upright (2) as shown, insert the Pivot Axle
(16) into the Upper Body Legs and the Upright. Be
careful not to damage the Upper Wire Harness
(18) with the Pivot Axle.
Place a Wave Washer (27) on each end of the Pivot
Axle (16). Then, tighten an 8 x 23mm Button
Screw (65), an 8 Washer (64), and a Pivot Cover
(14) into each end of the Pivot Axle.
5
14
27
6
2
18
6
65
64
14
64
27
16
Grease
Grease
65

8
73
7. Attach the Left Pedal Arm (21) to the left Upper
Body Leg (6) with an 8 x 23mm Button Screw
(65), an 8 Washer (64), and a Pedal Leg Cover
(23).
Apply grease to a Large Wave Washer (20) and
slide it onto the Left Crank Arm (42). Then, attach
the Left Pedal Arm (21) to the Left Crank Arm with
an 8 x 25mm Patch Screw (70) and an 8 Large
Washer (81).
Repeat this step for the other side of the elliptical
exerciser.
See step 3. Tighten the four 8 x 19mm Patch
Screws (73).
7
Grease
20
81
70
23
64
21
6
65 42
6. Apply a generous amount of grease to the axle on
the left Upper Body Leg (6). Then, apply grease to a
Large Wave Washer (20) and slide it onto the axle.
Apply a generous amount of grease to the Left
Crank Arm (42). Then, slide a Crank Arm Spacer
(45) onto the Left Crank Arm. Make sure the flat
side of the Crank Arm Spacer is facing away from
the Left Crank Arm.
Slide the Left Pedal Arm (21) onto the left Upper
Body Leg (6) and onto the Left Crank Arm (42).
Repeat this step for the other side of the elliptical
exerciser.
6
6
21
20
Grease
Grease
45
8
8. The Console (10) requires four “AA” batteries (not
included); alkaline batteries are recommended.
Remove the battery cover from the Console. Insert
four batteries into the Console; make sure that the
batteries are oriented as shown by the markings
inside the battery compartment. Then, reattach
the battery cover. 10
Batteries
Battery
Cover
42

9
10
75
67
67
6
10. Orient a Left Upper Body Insert (12) and a Right Upper
Body Insert (13) as shown, and press them together
around the left Upper Body Leg (6). Next, slide the Left
Upper Body Arm (4) onto the Upper Body Inserts.
While another person holds the Left Upper Body Arm
(4) and the Upper Body Inserts (12, 13), insert an
10 x 50mm Carriage Bolt (75) through all three parts
from the inside as shown. Next, tighten four 4 x
32mm Screws (67) and four 4 x 12mm Flat Head
Screws (88) through the Left Upper Body Arm and into
the Upper Body Inserts. Then, tighten an Arm Knob
(11) onto the Carriage Bolt.
Attach the Right Upper Body Arm (not shown) to
the right Upper Body Leg (6) in the same way. 6
11
88
12
88
13
88
4
88
9
10
2
18
60 17
66
9. While another person holds the Console (10) near the
Upright (2), connect the Upper Wire Harness (18) to
the wire harness on the Console.
Tip: Be careful not to pinch the wire harnesses.
Attach the Console (10) to the Upright (2) with four
4 x 16mm Screws (60).
Attach the Water Bottle Holder (17) to the Upright (2)
with two 4 x 22mm Screws (66).
11. Make sure that all parts of the elliptical exerciser are properly tightened. Place a mat under the elliptical
exerciser to protect the floor or carpet from damage.

10
HOW TO USE THE ELLIPTICAL EXERCISER
HOW TO MOVE AND LEVEL THE ELLIPTICAL
EXERCISER
To move the elliptical exerciser, stand in front of it,
place one foot against one of the wheels, and firmly
hold the upper end of the upright. Pull the upright until
you can move the elliptical exerciser on the wheels.
Carefully move the elliptical exerciser to the desired
location and then lower it. CAUTION: To decrease
the risk of injury, do not attempt to move the ellip-
tical exerciser over an uneven surface.
If the elliptical exerciser rocks slightly on your floor,
turn one or both of the levelling feet under the front
stabilizer until the rocking motion is eliminated.
HOW TO ADJUST THE HEIGHT OF THE UPPER
BODY ARMS
The upper body arms
can be adjusted to the
height that is the most
comfortable for you.
Simply loosen the arm
knobs, slide the upper
body arms to the desired
height, and then firmly
tighten the arm knobs.
ake sure that both
upper body arms are at
the same height.
HOW TO EXERCISE ON THE ELLIPTICAL
EXERCISER
To mount the elliptical exerciser, firmly hold the upper
body arms and carefully step onto the pedal that is in
the lowest position. Next, step onto the other pedal.
Push the pedals until they begin to move with a con-
tinuous motion. Note: The pedal discs can turn in
either direction. It is recommended that you turn
the pedal discs in the direction shown below;
however, for variety, you can turn the pedal discs
in the opposite direction.
To dismount the elliptical exerciser, allow the pedals
to come to a complete stop. CAUTION: The elliptical
exerciser does not have a freewheel; the pedals
will continue to move until the flywheel stops.
When the pedals are stationary, step off the highest
pedal first. Then, step off the lowest pedal.
Pedal
Pedal
Disc
Upper
Body Arm
Upper
Body
Arm
Arm Knob
Wheel
Upright
Leveling Foot