Westin 56-23935 User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-562393-RevB ECO #: W16-0090 DATE: 9/8/16
INSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS,
HDX EXTREME BOARD
APPLICATION:
2015-2017 Ford F150 Super Crew and Super Cab
2017 Ford F250/350 Super Cab and Crew Cab
PART NUMBER:
56-23935, 56-23945
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
12RUNNING BOARDS 13MM SOCKET
21DRIVER FRONT MOUNT BRACKET 13MM WRENCH
31PASSENGER FRONT MOUNT BRACKET ALLEN WRENCH
41DRIVER REAR MOUNT BRACKET SOCKET EXT.
51PASSENGER REAR MOUNT BRACKET RATCHET
61* DRIVER CENTER MOUNT BRACKET TORQUE WRENCH
71* PASSENGER CENTER MOUNT BRACKET
84 / 6* UNIVERSAL MOUNT BRACKET
924 / 36* M8 SPLIT LOCK WASHER (YELLOW ZINC)
10 24 / 36* M8 FLAT WASHER (YELLOW ZINC)
11 8 / 12* M8 HEX HEAD CAP SCREW (YELLOW ZINC)
12 16 / 24* M8 HEX NUT (YELLOW ZINC)
13 4 / 6* M8 ROUND HEAD SQUARE NECK BOLT (BLACK ZINC)
14 12 / 18* M8 PLASTIC RETAINER SQUARE
* SUPER CREW HAS CENTER MOUNT BRACKETS AND THEREFORE COMES WITH MORE HARDWARE
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
CARE INSTRUCTIONS
 REGULAR WAXING IS RECOMMENDED. DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES.
 STAINLESS STEEL PRODUCTS CAN BE CLEANED WITH MILD SOAP AND WATER. STAINLESS STEEL POLISH SHOULD BE USED TO POLISH SMALL SCRATCHES.
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER.
ITEM 1 ITEM 2 ITEM 8ITEM 3 ITEM 7ITEM 6
REAR BRACKETS OPPOSITE OF FRONT

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-562393-RevB ECO #: W16-0090 DATE: 9/8/16
2. Start installation on driver’s side. On the rocker panel find locations of factory studs. In each location there should be 3
studs. (Note: Super Cab has two locations and Super Crew has three locations.) See Figure 1.
3. Insert (1) M8 Plastic Retainer (Item 14) on each factory stud. (Note: There will be 6 extra plastic retainers for the super cab
model.) See Figure 2.
4. Insert the M8 round head square neck bolt (Item 13) through the Universal Mounting Bracket’s (Item 8) square hole. Then
insert the M8 round head square neck bolt through mounting brackets (Item 2 - 7) bottom circular hole. Loosely secure
with (1) M8 hex nut, (1) M8 split lock washer, and (1) M8 flat washer. (Note: For Super Cab model there will be 4 Univer-
sal Mounting Brackets and for the Super Crew model there are 6.) See Figure 3.
5. Align sub-assembly with the 3 factory studs. Lower 2 factory studs will align with the Universal Mounting Bracket and top
factory stud will align with mounting brackets. Loosely secure sub-assembly with (3) M8 hex nut, (3) M8 split lock wash-
er, and (3) M8 flat washer. See Figure 4. (Note: See page 3 for br acket orientation)
6. Repeat Step 3-5 for every mounting location.
Figure 1
Factory studs shown
Front Driver side shown Figure 2
14
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim.
Figure 3 Figure 4
Front Driver
Side Mounting
Location Shown Figure 4
Front Driver
Side Mounting
Location Shown

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-562393-RevB ECO #: W16-0090 DATE: 9/8/16
7. For Step Board installation to the previously installed mounting brackets use the supplied M8 hardware. See Figures 5 & 6.
8. Align step bar and brackets to desired positioning then torque and tighten all: M8 hardware to 15-18 ft-lbs.
NOTE : (FOR SUPER CAB APPLICATIONS THE ORIENTATION OF BRACKETS ARE THE SAME.
THE ONLY DIFFERENCE IS IT WILL NOT HAVE CENTER BRACKETS.)
Front Driver Side Shown
Figure 5 Figure 6
Center Driver Side Shown
Super Crew Driver Side Shown
Forward Item 2Item 4
Item 6
Super Crew Passenger Side Shown
Forward Item 5
Item 7
Item 3
Step pads not shown
INSTALLATION COMPLETE

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-562393-RevB ECO #: W16-0090 DATE: 9/8/16
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RESULT IN
PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY:
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product. Us-
er should never exceed the vehicle manufacturers maximum tow and weight rating regardless of
the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS
VEHICLE DAMAGE.
WARNING
AUTOMOTIVE PRODUCTS, INC.