Westin PRO TRAXX 4 OVAL TUBE STEP BARS User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-212331-RevC ECO #: W16-0082 DATE: 2/16/17
INSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS,
PRO TRAXX 4 OVAL TUBE STEP BARS
APPLICATION:
2007-2017 Jeep Wrangler 2-Door
PART NUMBER:
21-23310, 21-23315
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
1,2 2 STEP BARS, DRIVER (1) AND PASSENGER (2) 16MM SOCKET
3 2 FRONT MOUNTING BRACKET 16MM WRENCH
4 2 FRONT SUPPORT BRACKET 5MM HEX DRIVER/
ALLEN KEY
5 2 REAR MOUNTING BRACKET
6 2 REAR SUPPORT BRACKET 13MM SOCKET
7 12 M8 HEX CAP SCREW (BLACK ZINC) 13MM WRENCH
8 24 M8 FLAT WASHER (BLACK ZINC) POWER DRILL
9 12 M8 SPLIT LOCK WASHER (BLACK ZINC) 5/16” -3 /8” DRILL BIT
10 12 M8 HEX NUT (BLACK ZINC) RATCHET
11 8 M10 HEX SOCKET BUTTON HEAD SCREW (BLACK ZINC) TORQUE WRENCH
12 12 M10 FLAT WASHER (BLACK ZINC)
13 8 M10 INTERNAL TOOTHED LOCK WASHER (BLACK ZINC)
14 4 M10 HEX CAP SCREW (BLACK ZINC)
15 4 M10 SPLIT LOCK WASHER (BLACK ZINC)
16 4 M10 NUT PLATE
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim.
ITEM 3 ITEM 5ITEM 4 ITEM 6
Front Front Rear Rear

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-212331-RevC ECO #: W16-0082 DATE: 2/16/17
2. Starting at the front driver side mounting location. The
bottom rocker mounting hole may be covered by black
tape. After removal, insert M10 nut plate through the
square hole. Some vehicles may already be equipped
with a threaded hole. See Figure 1.
6. Repeat Steps 3-5 for the driver rear mounting bracket and
support bracket. See Figure 3.
Do not fully tighten at this time.
Figure 3
Item 16
Front
Figure 1
3. Attach the driver front mounting bracket to the vehicle un-
derbody using (1) M10 hex cap screw, (1) M10 split lock
washer, and (1) M10 flat washer. See Figure 2.
4. Attach the driver side front support bracket to the pinch
weld of the vehicle using (2) M8 hex cap screws, (4) M8
flat washers, (2) M8 split lock washers, and (2) M8 hex
nuts. One more holes located on the pinch weld may have
to be enlarged using a 5/16”-3/8” drill bit. See Figure 2.
5. Secure the support bracket to the main mounting bracket
using (1) M8 hex cap screw, (2) M8 flat washers, (1) M8
split lock washer, and (1) M8 hex nut. See Figure 2. Do
not fully tighten mounting & support brackets at this time. Figure 2

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-212331-RevC ECO #: W16-0082 DATE: 2/16/17
Care Instructions
 REGULAR WAXING IS RECOMMENDED. DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES.
 STAINLESS STEEL PRODUCTS CAN BE CLEANED WITH MILD SOAP AND WATER. STAINLESS STEEL POLISH SHOULD BE USED TO POLISH SMALL SCRATCHES.
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER.
7. At this time attach the driver side step bar to the driver
side mounting brackets using (6) M10 hex socket but-
ton head screws, (6) M10 internal toothed lock wash-
ers, and (6) M10 flat washers. See Figure 4.
8. Align all mounting brackets and step bar as desired.
Tighten all M8 fasteners to 15-18 ft-lbs., M10 hex cap
screws to 30 ft-lbs, and M10 button head screws to 18
ft-lbs.
9. Repeat Steps 2-8 for passenger side components. Figure 4
INSTALLATION COMPLETE
Item 4
Bracket Orientation for driver and passenger side shown
Item 3
Item 3
Item 5
Item 5
Item 4
Item 6
Item 6
Driver Side
Passenger Side
Front
Rear

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-212331-RevC ECO #: W16-0082 DATE: 2/16/17
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RESULT IN
PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY:
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product.
User should never exceed the vehicle manufacturers maximum tow and weight rating regardless
of the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS
VEHICLE DAMAGE.
WARNING
AUTOMOTIVE PRODUCTS, INC.