Westin SG6 User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-2757-RevB ECO #: W19-0187 DATE: 12/31/19
INSTALLATION INSTRUCTIONS
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
1 2 END CAP “A” PHILIPS-HEAD SCREWDRIVER
2 2 END CAP “B” WIRE CUTTER
3 2 ALUMINUM EXTRUSION
4 2 CLOSE OUT PANEL
5 2 RUBBER PAD
6* 1 WIRING HARNESS
7 12 M4 PAN HEAD SCREW
8* 8 DOUBLE SIDED TAPE
9* 4 MAGNETIC SWITCH
10* 4 LED LIGHT
11* 12 ZIP TIES
* SG6 LED RUNNING BOARDS ONLY
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
CONTENT
SG6 LED RUNNING BOARDS / SG6 RUNNING BOARDS
PART NUMBER:
27-64710, 27-64715, 27-65710, 27-65715, 27-64720, 27-64725, 27-65720,
27-65725, 27-64730, 27-64735, 27-65730, 27-65735, 27-64740, 27-64745,
27-65740, 27-65745, 27-64750, 27-64755, 27-65750, 27-65755, 27-64760,
27-64765, 27-65760, 27-65765
ITEM 4
ITEM 3
ITEM 2ITEM 1
LED END CAPS SHOWN
NON-LED END CAPS ARE SIMILAR
ITEM 5
83” ITEMS SHOWN
OTHER LENGTHS ARE SIMILAR
ITEM 10

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-2757-RevB ECO #: W19-0187 DATE: 12/31/19
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim.
Fig. 1
1. Remove one of the End Caps (1 or 2) by
removing the three M4 pan head screws (7)
from the back and bottom of the End Cap
and sliding the End Cap off of the
Aluminum Extrusion (3). See Figure 1.
Close Out Panel Installation (Optional)
For vehicles with the required space, the close out panel can be installed to fill the area above the running board.
Remove Three Pan Head
Screws and Slide End Cap
Off of Aluminum Extrusion
2. Slide a Close Out Panel (4) into the groove
in the back of the Aluminum Extrusion (3).
See Figure 2.
Fig. 2

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-2757-RevB ECO #: W19-0187 DATE: 12/31/19
3. Replace the End Cap (1 or 2) that was removed in Step 1 and reinstall the M4 pan head screws (7). See Figure 3.
Fig. 3 SG6 LED Running Board Assembly
For SG6 LED Running Boards:
Wiring Harness and Magnetic Switch Installation (Varies with Vehicle)
Note: Install wiring harness and magnetic switches after mounting the running boards onto the vehicle. Refer to
mount kit installation sheet for mounting instructions.
1. Connect the Wiring Harness (6) to each LED
Light (10). See Figure 4.
2. Install the magnetic switches. Refer to Pages 4 &
5for examples.
Fig. 4

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-2757-RevB ECO #: W19-0187 DATE: 12/31/19
3. Place the Magnetic Switches (9) on the Double Sided Tape (8). Note: It is extremely important that the switches face each
other. They will not work if positioned incorrectly. See Figure 6.
Fig. 6 Passenger Rear Shown
1. For each door, find a suitable location on the door and the cab of the truck to mount the Magnetic Switches (9).
The switches must line up and cannot be more than 2 cm apart.
2. Once a location is found, place the Double Sided Tape (8) as shown in Figure 5.
Passenger Rear Shown
CAB DOOR
Fig. 5
ALL VEHICLES WILL HAVE DIFFERENT WAYS TO MOUNT THE MAGNETIC SWITCHES PROPERLY.
MOUNT IN THE BEST APPLICATION FOR YOUR VEHICLE
SEE BELOW FOR DIFFERENT EXAMPLES

5
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-2757-RevB ECO #: W19-0187 DATE: 12/31/19
Fig. 8
Place the Other Switch on the Edge of Rocker
Panel Just Below the Door
Passenger Front ShownFig. 7 Passenger Front Shown
Place Switch on Bottom Edge of Door Towards the Rear
Fig. 9
3. Repeat the process for the rear door locations.
1. For each door, find a suitable location on the door and the cab of the truck to mount the Magnetic Switches (9).
The switches must line up and cannot be more than 2 cm apart.
2. Once a location is found, place the Double Sided Tape (8) and Magnetic Switch (9) as shown in Figures 7, 8 & 9.
Note: Suggested location shown.
SEE BELOW FOR DIFFERENT EXAMPLES

6
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-2757-RevB ECO #: W19-0187 DATE: 12/31/19
1. For each door, find a suitable location on the door and the cab of the truck to mount the Magnetic Switches (9).
The switches must line up and cannot be more than 2 cm apart.
2. Once a location is found, place the Double Sided Tape (8) and Magnetic Switch (9) as shown in Figure 10 . Note: Sug-
gested location shown. Note: It is extremely important that the switches face each other. They will not work if positioned
incorrectly.
Door Side
Cab Side
Fig. 10
SEE BELOW FOR DIFFERENT EXAMPLES

7
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-2757-RevB ECO #: W19-0187 DATE: 12/31/19
3. Run the Wiring Harness (6) to the engine compartment. Use Zip Ties (11) as needed to secure slack wiring. See Figure 10.
Find a Place with Minimal Heat
and Minimal Exposure to the
Elements to Run the Harness
Fig. 11
4. Be sure to disconnect the battery prior to connecting the wiring harness.
5. Connect the red ring connector to the positive terminal on the battery and the black ring connector to the negative terminal.
See Figures 11 and 12.
6. Reconnect the battery.
Fig. 12 Fig. 13

8
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-2757-RevB ECO #: W19-0187 DATE: 12/31/19
CARE INSTRUCTIONS
 REGULAR WAXING IS RECOMMENDED. DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES.
 STAINLESS STEEL PRODUCTS CAN BE CLEANED WITH MILD SOAP AND WATER. STAINLESS STEEL POLISH SHOULD BE USED TO POLISH SMALL SCRATCHES.
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER.
INSTALLATION COMPLETE

9
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-2757-RevB ECO #: W19-0187 DATE: 12/31/19
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
WARNING
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RESULT IN
PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY:
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product.
User should never exceed the vehicle manufacturers maximum tow and weight rating regardless
of the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL
AS VEHICLE DAMAGE.