Westin HDX Bandit User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5831135-RevA ECO #: W18-0228 DATE: 08/21/2019
INSTALLATION INSTRUCTIONS
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
11HDX BUMPER 18MM SOCKET
21DRIVER MOUNTING BRACKET 18MM WRENCH
31PASSENGER MOUNTING BRACKET 19MM SOCKET
41DRIVER SUPPORT BRACKET A 19MM WRENCH
51PASSENGER SUPPORT BRACKET A 10MM SOCKET
61FOG LIGHT BRACKET A 10MM WRENCH
71FOG LIGHT BRACKET B 15MM SOCKET
81FOG LIGHT BRACKET C RATCHET
91FOG LIGHT BRACKET D TORQUE WRENCH
10 1DRIVER SUPPORT BRACKET BPLIERS
11 1PASSENGER SUPPORT BRACKET B UTILITY KNIFE
12 2SENSOR BRACKET
13 2PARKING SENSOR PLUG
14 6LONG M12 HEX HEAD CAP SCREW (YELLOW ZINC)
15 6SHORT M12 HEX HEAD SCREW (YELLOW ZINC)
16 6MEDIUM M12 HEX HEAD CAP SCREW (YELLOW ZINC)
17 18 M12 SERRATED FLANGE NUT (YELLOW ZINC)
18 4M12 HEX NUT (YELLOW ZINC)
19 22 M12 SPLIT LOCK WASHER (YELLOW ZINC)
20 6 LARGE M12 FLAT WASHER (YELLOW ZINC)
21 16 SMALL M12 FLAT WASHER (YELLOW ZINC)
22 10 M10 HEX HEAD CAP SCREW (YELLOW ZINC)
23 10 M10 SPLIT LOCK WASHER (YELLOW ZINC)
24 10 M10 FLAT WASHER(YELLOW ZINC)
25 8M6 HEX HEAD CAP SCREW (BLACK ZINC)
26 4M6 ROUND HEAD SQUARE NECK CAP SCREW (BLACK ZINC)
27 10 M6 HEX NUT (BLACK ZINC)
28 12 M6 SPLIT LOCK WASHER (BLACK ZINC)
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
CONTENT
HDX BANDIT FRONT BUMPER
APPLICATION:
2019 Chevrolet Silverado 1500 (Excl. 2019 Silverado LD)
PART NUMBER:
58-31135

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5831135-RevA ECO #: W18-0228 DATE: 08/21/2019
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim.
29 18 M6 FLAT WASHER (BLACK ZINC)
30 2LISCENSE PLATE GROMMET
31 4M12/M10 BOLT/NUT PLATE
ITEM 2ITEM 1
ITEM 4 ITEM 6
ITEM 7 ITEM 10 ITEM 12
ITEM 3
ITEM 5 ITEM 8
ITEM 9 ITEM 11

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5831135-RevA ECO #: W18-0228 DATE: 08/21/2019
2. Begin by removing the plastic trim fasteners holding the grille in place. Also dethatch the clips of the wings of the grille.
See Figures 1 & 2.
3. Remove the grille by pulling firmly and carefully at the bottom of the grille.
Fig 2
Fig 1
Remove trim
fasteners
4. Remove the 4 bolts behind the plastic cover securing the bumper to the vehicle. See Figure 3.
5. Remove the bolts on the bottom of the frame securing the bumper supports to the vehicle. See Figure 4.
6. Unplug any wire connections and remove the bumper.
Fig 3 Fig 4

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5831135-RevA ECO #: W18-0228 DATE: 08/21/2019
7. If reusing the factory fog lights, remove them from the OEM Bumper. If aftermarket lights will be used, install them at this
time and move to Step 9.
8. Using Items 6-9 and supplied M6 hardware, reinstall the fog lights on to the Bandit bumper. See Figure 5-6.
Note: Fog light brackets “A” and “B” belong to the driver side while fog light brackets “C” and “D” belong to the pas-
senger side
9. If equipped, reinstall sensors on to the HDX Bandit bumper. Note: A separate parts kit will need to be purchased in order
to install parking sensors. Refer to PN 58-30005 for instructions.
Bracket A Bracket B
Fig. 5
Driver side shown, passenger side (8,9) similar
26
27
28
29
25
Fig. 6
Driver side shown
25
25
6
7

5
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5831135-RevA ECO #: W18-0228 DATE: 08/21/2019
10. Install the mounting brackets onto the frame using supplied M10 hardware. You will use the factory welded M10 nuts to
mount the brackets See Figure 7-8.
11. Install the Support brackets on to the frame and main brackets using supplied M10 and M12 hardware. Note: 1 Y ou will
have to slide the bolt/nut plate through the exposed hole in the frame in order to install support brackets. Note 2: Be sure
to install nut plate with the M12 bolt side facing towards the front of the vehicle. See Figures 9-11.
Mount to frame
2
22
23
24
Fig. 8
Fig. 7
Driver side shown

6
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5831135-RevA ECO #: W18-0228 DATE: 08/21/2019
Fig. 9
Insert Nut Plate (31)
through here
Passenger side will require (2)
Short M12 Hex Head Bolts
2
10
4
31
24
18
Fig. 10
16
Driver side shown
22
17
15
17
23
21
22
21
19
19

7
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5831135-RevA ECO #: W18-0228 DATE: 08/21/2019
18
11
19
21
22
31
17
Fig. 11
Passenger side shown
12. With help, lift the HDX Bumper (1) into place between the Mount Brackets (2,3) and attach with supplied M12 Hardware.
See Figure 12. CAUTION: The HDX Bandit Bumper is ver y heavy. The use of a floor jack or hoist is recommended.
14 19 20
17
2
Driver side shown
Fig. 12
5
15
15
19
24
23
21
17
Driver side will require (1)
Short M12 Hex Head Bolt
16

8
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5831135-RevA ECO #: W18-0228 DATE: 08/21/2019
13. Install the two license plate grommets as shown in Figure 13 and install license plate using OEM hardware.
14. Trim the inner fender as desired. See Figure 14.
15. Align and adjust the bumper as necessary. Once the desired fit is achieved, torque all hardware as specified: torque M10
Hardware to 30-35 ft-lbs, M12 to 45-50 ft-lbs.
Fig 13
30
30
Fig 14
Trim Inner Fender liner

9
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5831135-RevA ECO #: W18-0228 DATE: 08/21/2019
CARE INSTRUCTIONS
 REGULAR WAXING IS RECOMMENDED. DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES.
 STAINLESS STEEL PRODUCTS CAN BE CLEANED WITH MILD SOAP AND WATER. STAINLESS STEEL POLISH SHOULD BE USED TO POLISH SMALL SCRATCHES.
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER.
INSTALLATION COMPLETE

10
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5831135-RevA ECO #: W18-0228 DATE: 08/21/2019
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
WARNING
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RESULT IN
PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY: (if applicable)
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product.
User should never exceed the vehicle manufacturers maximum tow and weight rating regardless
of the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL
AS VEHICLE DAMAGE.
FOR CALIFORNIA RESIDENTS ONLY-PROP 65 WARNING:
Some products may contain chemicals such as DEHP, which can cause cancer, birth defects or
other reproductive harm. For more info go to www.p65warnings.ca.gov