Whalen SIG3IN1CGT User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Mfg., Inc. Page 1 Factory No. 33-10944
Signa Gaming TheaterTM 3-in-1TM TV Stand
Model # SIG3IN1CGT
U.S. Patents 8,079,311 & 8,191,485 and other Patent Pending
This item is designed to be a 3-in-1 configuration. Please choose the option that best suits your
needs. DO NOT discard any of the hardware or parts that you will not use on your chosen option.
This will allow you to use this TV Console in different configurations at a later date, if desired.
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this
item to the store where it was purchased. Please call our customer service number and have
your instructions and parts list ready to provide the model name, part name or factory
number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

Model # SIG3IN1CGT
Whalen Furniture Mfg., Inc. Page 2 Factory No. 33-10944
MANUFACTURER: Whalen Furniture Mfg., Inc.
CATALOG: Signa Gaming TheaterTM 3-in-1TM TV Stand (SIG3IN1CGT)
DATE OF MANUFACTURE: December 2012
MADE IN CHINA
1. Please read the Assembly Instructions prior to assembling this product.
2. Remove all hardware from the box and sort by size.
3. Check to see that all hardware and parts are present BEFORE assembling.
4. Ask a friend to assist you with the assembly of this furniture.
5. To avoid damage, assemble the product on a sturdy, level and protective surface.
6. Please wait until all steps are completed before fully tightening bolts.
7. Make sure all bolts are tightly fastened before the unit is used.
MAXIMUM RECOMMENDED WEIGHT LOADS
GENERAL INFORMATION
,
TIPS and TRICKS
This product is sold with a set of Tipping Restraint Hardware Kit. You must install the Tipping
Restraint Hardware between the wall and the TV console to prevent any accidents or
damages. When properly installed, this restraint can provide protection against the unexpected
tipping of the unit due to small tremors, bumps or climbing. The restraint is only a deterrent and
is not a substitute for proper adult supervision. Use of tip-over restraints may only reduce, but
not eliminate, the risk of tip-over.
FITS UP TO MOST 60” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.2 kg)
FITS UP TO MOST 60” FLAT PANEL TVs
WITHOUT SWIVELING BRACKET
MAXIMUM LOAD 135 lb. (61.2 kg)
MAXIMUM LOAD 50 lb. (22.6 kg)
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH
FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND
WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT
PANEL TVS OR EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE
CENTRE OF THE UNIT; CRT TVS, IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT
PANEL TVS OR OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT
LIMITS COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.
MAXIMUM LOAD 15 lb. (6.8 kg)

Model # NVS3IN1CGT
Whalen Furniture Mfg., Inc. Page 3 Factory No. 33-10944
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts are present
before beginning assembly.
A- Top Shelf Frame (1) B- Middle Shelf Frame (1) C- Bottom Shelf Frame (1)
D- Long Spine (1) D1- Short Spine (1)
E- Left Leg (1) F- Right Leg (1) G- Top Glass (1)
H- Middle Glass Shelf (1) I- Bottom Glass Shelf (1) J- Swiveling Bracket (1)
(Pre-attached)
K- Mounting Frame (1) L- Monitor Bracket (2) M- SSS Spine (1)
N- Sensor/Sound Shelf (1) O- Cable Wheel (2)
LR
LL

Model # SIG3IN1CGT
Whalen Furniture Mfg., Inc. Page 4 Factory No. 33-10944
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts are present
before beginning assembly.
(1) Suction Cup (2) 1/2” Bolt (3) 3/4” Bolt (4) 1-1/4” Bolt (5) Lock Washer
(24+1 extra) (8+1 extra) (12+1 extra) (8+1 extra) (24+1 extra)
(6) Flat Washer (7) Concrete Anchor (8) 2-1/2” Lag Bolt (9) Large Flat Washer
(24+1 extra) (4) (4) (4+1 extra)
M4 Allen Wrench 3/16” Allen Wrench Touch-up Pen Tipping Restraint Hardware Kit (1)
(1) (1) (1) (Inside Plastic Bag)
TV Mounting Kit
M4 x 12 Bolt (4) M4 x 30 Bolt (4) M5 x 12 Bolt (4) M5 x 30 Bolt (4)
M6 x 12 Bolt (4) M6 x 35 Bolt (4) M8 x 16 Bolt (4) M8 x 40 Bolt (4)
M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)
Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)
Tools required: Allen Wrench (provided) and Phillips screwdriver (not provided).

Model # NVS3IN1CGT
Whalen Furniture Mfg., Inc. Page 5 Factory No. 33-10944
Assembly Instructions
NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,
go back and fully tighten all bolts. This will make the assembly easier.
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Choose the option suits your needs. For the Floating Swivel Mount option, select the Long
Spine (D). For the other two options, select the Short Spine (D1). Set the Spine back face down
on a scratch free surface, as shown.
3. Align and attach 3 Shelf Frames (A, B and C) to the Spine. Make sure the inside corner plates
on the shelf frames will face up when the unit is turned upright.
1-1/4” Bolt
(4 used in this step)
④
Lock Washer
(6 used in this step)
⑤
Flat Washer
(6 used in this step)
⑥
3/4” Bolt
(2 used in this step)
③
B/C
D/D1

Model # SIG3IN1CGT
Whalen Furniture Mfg., Inc. Page 6 Factory No. 33-10944
Assembly Instructions
4. Stand the unit upright.
5. Align and attach the Left Leg (E) to the Top Shelf Frame (A) by inserting two 1-1/4” Bolts (4)
with Washers (5 and 6) from inside the Shelf Frame through the pre-drilled holes on the side
rail into the threaded inserts on the Leg. Make sure that top rail of Leg is flush with the wooden
front rail of Top Shelf Frame. DO NOT tighten the bolts.
6. Secure the Left Leg (E) to the Lower Shelf Frame (B and C) using the 3/4” Bolts (3) with
Washers (5 and 6) through the end bracket holes into the Leg.
7. Repeat the last 2 steps with the Right Leg (F). Make sure the gaps between the wooden front
rail of Top Shelf Frame and Legs are equal. Loosen the Bolts on the wooden front rail and
adjust, if necessary.
1-1/4” Bolt
(4 used in this step)
④
3/4” Bolt
(6 used in this step)
③
Lock Washer
(10 used in this step)
⑤
Flat Washer
(10 used in this step)
⑥
D

Model # NVS3IN1CGT
Whalen Furniture Mfg., Inc. Page 7 Factory No. 33-10944
Assembly Instructions
8. Go back and tighten all Bolts with the provided M4 Allen Wrench.
9. In case of uneven floor, Floor Levelers are provided at the bottom of both Legs (E and F).
Simply tilt the unit back and raise or lower Floor Leveler by hand to correct tilting, as shown
above.
If you choose Table-top Console
configuration, continue to step 10.
If mounting TV with the Floating Swivel
Mount, skip ahead to PAGE 11.

Model # SIG3IN1CGT
Whalen Furniture Mfg., Inc. Page 8 Factory No. 33-10944
Assembly Instructions for Table-top Console
10.Attach 2 Cable Wheels (O) to the backside of the Short Spine (D1) with the 3/4” Bolts (3).
Tighten the Bolts with the provided M4 Allen Wrench.
11.The Cable Wheels (O) enable you to shorten, separate and route cables and cords. Using the
Cable Wheels you can create a system for routing cables through channels, between
components and to power sources without tangled mess or annoying signal interference.
3/4” Bolt
(4 used in this step)
③
D1

Model # NVS3IN1CGT
Whalen Furniture Mfg., Inc. Page 9 Factory No. 33-10944
G
1
B/C
Assembly Instructions for Table-top Console
12.Put the Suction Cups (1) firmly into top holes and inside corner plates on 3 Shelf Frames (A, B
and C), as shown.
TIP: If a Suction Cup resists insertion, try pressing down on the middle of the cup with the
Allen Wrench while twisting it clockwise into the hole.
13.Place the Top Glass (G) and Glass Shelves (H and I) in place starting from the Bottom Glass
Shelf, as shown above. Make sure the glass shelf is properly centered. Push each glass shelf
all the way back against the Spine. Also, be sure to press down evenly and firmly each glass
shelf onto the Suction Cups to make sure they securely rest onto the Suction Cups.
NOTE: If a glass shelf is scratched, you can minimize the damage by using a BLACK marker
and filling in scratched area from underneath.
Suction Cup
(24 used in this step)
①

Model # SIG3IN1CGT
Whalen Furniture Mfg., Inc. Page 10 Factory No. 33-10944
Assembly Instructions for Table-top
Tools required: Allen Wrench (provided), Phillips screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.
14.Position the assembled console at the desired location against a wall. Now, follow the
instructions printed on the plastic bag containing the Tipping Restraint Hardware to mount the
tipping restraint to the Spine and the wall.
NOTE: YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO THE
WALL, TO PREVENT FROM TIPPING, CAUSING ACCIDENTS AND/OR INJURIES.
15.The Console is now ready for use. Be sure to position your Flat Panel TV in the center of the
console.
NOTE: If you choose the Tilting Wall Mount configuration, proceed to PAGE 19.