Whalen Montcross 908722 User manual

Whalen Furniture Manufacturing Page 1 Factory No. 15713
Date 2015-03-31 Rev.1 Factory: HOAJOI E
Montcross 7 Piece Dining Set
ITM. / ART. 908722
Model # MON7PD-E
ASSEMBLY INSTRUCTIONS
IMPORTANT, RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362 (English, Frenchand Spanish)
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday
(in the US and Canada only)
LOT NUMBER:
DATE PURCHASED:
/
/

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 2
E
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or
replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet
your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to State.
AUSTRALIA: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure.
Customer Service: 1-866-942-5362 (English, French and Spanish)
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to
Friday (in the US and Canada only)
1. Maximum load weight on table is 181.4 kg / 400 lb
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware and parts out of the reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all bolts and screws are tightly fastened before the unit is used.
6. Check that all bolts, screws and knobs are tight at least every 3 months or as needed.
MAXIMUM RECOMMENDED WEIGHT LOADS
THIS UNIT IS INTENDED FOR USE ONLY WITH THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM
WEIGHTS INDICATED MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.
GENERAL INFORMATION, TIPS & TRICKS

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 3
E
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Table Top (1x)
B- Outer Leg (2x) C- Inner Leg (2x)
(With one Female Plastic Fitting)
D- Stretcher (1x) E- Mounting Board (2x) F- Tenon Attachment (2x)
AA- Bolt BB- Large Lock Washer CC- Large Flat Washer
(16x+1 extra) (20x+1 extra) (16x+1 extra)
DD- Bolt (4x+1 extra) EE- Small Flat Washer (4x+1 extra)
Allen Wrench (1x) Touch-up Pen (1x)
Tools required: Allen wrench (included).

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 4
E
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Combine one Outer Leg (B) and one Inner Leg (C) together by fitting the cutouts properly.
3. Attach the leg assembly to the Stretcher (D) by threading two Bolts (DD) with Lock Washers (BB) and
Small Flat Washers (EE) through the countersunk holes on the Outer Leg (B) and then screw into the
threaded inserts on the Stretcher. Tighten the bolts with the enclosed Allen Wrench.
4. Repeat the same procedure to attach the other two Legs (B and C) to the Stretcher (D) at the opposite
end. Make sure that the threaded holes on the top of each Leg point upward.
DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are
ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the nuts or bolts.
B
C
DDBB EE B
C
C
B
D
DD
BB
EE

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 5
E
Assembly Instructions
5. Align the center holes of one Mounting Board (E) with the locater dowels on the top of Legs (B and C)
and press them together. Insert four Bolts (AA) with Lock Washers (BB) and Large Flat Washers (CC)
through the countersunk holes of the Mounting Board (E) and securely screw into the Legs. As shown.
6. Repeat the same procedure with the other Mounting Board (E).
7. For nice looking, attach the Tenon Attachment (F) to cover the countersunk holes on each Outer Leg (B)
by engaging the plastic fitting. As shown.
E
E
CC
B
B
F
B
CC
BB
AA CC
BB
AA
CC
BB
AA
CC
BB
AA

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 6
E
Assembly Instructions
8. Place the Table Top (A) upside down on a level and protective surface. As shown.
9. Flip the assembled base upside down and align the drilled holes on Mounting Boards (E) with the
threaded inserts on the slide supports on the Table Top (A). Insert eight Bolts (AA) with Lock Washers
(BB) and Large Flat Washers (CC) through the drilled holes on the Mounting Boards (E) and then
securely screw into the slide supports, using the enclosed Allen Wrench.
E
E
A
CC
BB
AA
CC
BB
AA
CC
BB
AA
CC
BB
AA

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 7
E
Assembly Instructions
10.Ask for assistance to lift the unit upright and position it at the desired location.
11. Unlock the sash locks underneath the Table Top (A) and release the slide locks on both slide mechanisms
to allow the slide to operate, then pull the Table Top wide open equally from both ends.
12. Lift the Butterfly Leaf from the compartment of the Table Top (A). Flip up the leaf and rest it on one
slide support. Unfold the leaf aprons carefully.
13. Unfold the leaf and rest the top flap onto the other slide support.
14. Push the Table Top (A) from both ends to close and lock the sash locks underneath the Table Top. Flip
down the black toggle on each slide mechanism to lock the slides in place.
ON OFF
ON OFF

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 8
E
To Store the Butterfly Leaf When Not In Use
15.Unlock the sash locks underneath the Table Top (A) and release the slide locks on both slide mechanisms
to allow the slide to operate, then pull the Table Top wide open equally from both ends.
16. Fold two Center Leaves together and flip down the leaf aprons.
17. Rotate the Center Leaves and rest them onto the leaf support. As shown.
18. Push the Table Top (A) from both ends to close. Lock the sash locks underneath the Table Top and flip
down the black toggle on each slide mechanism to lock the slides in place.
ON OFF
ON OFF

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 9
E
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
Using solvents of any kind on your furniture may damage the finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
Stains or marks from crayons or ink markers will be difficult to remove.
In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
Check bolts/nuts periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
A touch-up pen has been provided to repair any small nicks or scratches that may occur during
assembly or shipping.
We hope you enjoy your purchase for many years.
Thank you for choosing Whalen Furniture!
www.baysidefurnishings.com
MADE IN VIETNAM / FABRIQUÉ AU VIETNAM / HECHO EN VIETNAM

IF YOU NEED TO REQUEST ANY REPLACEMENT PARTS, PLEASE USE THE LIST BELOW
Montcross 7-pc Dining Set (MON7PD-E)
*MON7PD-E-1-CB Chair Backrest *MON7PD-E-11A-PF Plastic Fitting *MON7PD-E-22-M8HN M8 Hex Nut *MON7PD-E-2-SF Seat Frame *MON7PD-E-12-TS Table Stretcher *MON7PD-E-23-M8x40B M8 x 40 mm Bolt *MON7PD-E-3-SC Seat Cushion *MON7PD-E-13-TTWS Table Top w/Slides *MON7PD-E-24-M8x80B M8 x 80 mm Bolt *MON7PD-E-4-SCS Seat Cushion Screw *MON7PD-E-13A-MSM Metal Slide Mechanism *MON7PD-E-25-M6x90B M6 x 90 mm Bolt *MON7PD-E-5-LSS Left Side Stretcher *MON7PD-E-14-BL Butterfly Leaf *MON7PD-E-26-LLW Large Lock Washer *MON7PD-E-6-RSS Right Side Stretcher *MON7PD-E-15-LHS Leaf Hinge w/Screws *MON7PD-E-27-LFW Large Flat Washer *MON7PD-E-7-LFL Left Front Leg *MON7PD-E-16-LHS Leaf Holder w/Screws *MON7PD-E-28-SFW Small Flat Washer *MON7PD-E-8-RFL Right Front Leg *MON7PD-E-17-SL Sash Lock *MON7PD-E-29-M4x40WS M4 x 40 mm Wood Screw *MON7PD-E-CHC Complete Hardware for Chair *MON7PD-E-18-LA Leaf Apron *MON7PD-E-30-M4AW 4 mm Allen Wrench *MON7PD-E-9-TIL Table Inner Leg *MON7PD-E-19-LAHS Leaf Apron Hinge w/Screws *MON7PD-E-31-OW Open Wrench *MON7PD-E-10-TOL Table Outer Leg *MON7PD-E-20-BGC Ball-style Grab Catches *MON7PD-E-32-TUP Touch-up Pen *MON7PD-E-11-TA Tenon Attachment *MON7PD-E-21-MB Mounting Board *MON7PD-E-CHT Complete Hardware for Table