Whalen Seymour BJAVCLSM-65 User manual

Seymour TV Console
Model # BJAVCLSM-65
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday
Or visit our website 24 hours a day, 7 days a week for product assistance at
www.whalenfurniture.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASE
D
:
/
/
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2020-07-24 Rev. 0001-A

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Seymour TV Console
MODEL # BJAVCLSM-65
How to adjust the European adjustable hinges on doors
Shipping may cause doors to go out of alignment. If you find that the doors need to be adjusted slightly,
turn the appropriate screw, as illustrated.
1. TO ADJUST DOOR FORWARD OR BACKWARD.
2. TO ADJUST DOOR TO RIGHT OR TO LEFT.
3. TO ADJUST DOOR UP OR DOWN.
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT
LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR
EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTER OF THE UNIT; THE
BASE OF THE TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE
UNIT WITHOUT OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR
FLAT PANEL TVS INCLUDING OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND
WEIGHT LIMITS COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.
FOR USE WITH TELEVISIONS WEIGHING 100 LBS (45.4 KG) OR LESS. USE WITH HEAVIER
TELEVISIONS MAY RESULT IN INSTABILITY CAUSING TIP OVER RESULTING IN DEATH OR
SERIOUS INJURY.
P
LACE
TV
BEHIND THE
STOPPER
FITS UP TO MOST 190.5 cm (75 in.)
DIAGONAL FLAT PANEL TVS
MAXIMUM LOAD 45.4 kg (100 lb)
MAXIMUM LOAD 22.7 kg (50 lb)
M A X I M U M R
E C O M M E N D E D W E I G H T L
O A D S
2
1
3

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 3 and 4 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH THE DOWELS. EXCESS GLUE CAN BE
WIPED OFF WITH A DAMP CLOTH.
Insert Dowel at least half way by tapping lightly with a rubber mallet (not included), IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the pre-drilled small holes on the panel. Connect both panels together; making sure
the Cam Bolt goes into the pre-drilled hole at the end of the panel with the Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole in the panel. Make sure the arrow on the Cam Lock is
pointed towards the Cam Bolt.
3. Once the Cam Bolt is connected inside the Cam Lock, take a Phillips screwdriver (not included) and
tighten the Cam Lock clockwise.
4. Plug the Cam Lock Cover into the cross slot of the Cam Locks to conceal the cam.
You are now ready to assemble the KD unit.
XX
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B-Left Side Frame (Qty. 1)
C- Right Side Frame (Qty. 1) D- Left Partition Panel (Qty. 1)
E- Right Partition Panel (Qty. 1) F- Bottom Panel (Qty. 1)
G- Top Front Stretcher (Qty. 1) H- Center Support (Qty. 2)
I- Door (Qty. 2) J- Small Shelf (Qty. 2)
K- Large Shelf (Qty. 1) L- Back Panel (Qty. 1)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 17+1 extra) (Qty. 17+1 extra) (Qty. 18+1 extra)
(4) M3.5 x 15 mm Washer Head Screw (5) M4 x 50 mm Screw (6) 5/32" x 22 mm Handle Bolt
(Qty. 28+1 extra) (Qty. 4+1 extra) (Qty. 4+1 extra)
(7) Cam Lock Cover (8) Acrylic Stopper (9) Handle
(Qty. 8+1 extra) (Qty. 1) (Qty. 2)
(10) Shelf Support (11) Rubber Bumper (12) M3.5 x 12 mm Screw
(Qty. 12+1 extra) (Qty. 4+1 extra) (Qty. 12+1 extra)
Glue Touch-up Pen Tipping Restraint Hardware Kit (Qty. 2)
(Qty. 1) (Qty. 1) (Included in plastic bag)
Tools required (not included): Phillips screwdriver, stud finder, power drill, pencil, tape measure, and
3 mm/0.1 drill bit.

6
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A) and both Side
Frames (B and C) with a Phillips screwdriver. NOTE: DO NOT over tighten the cam bolts.
3. Glue the Wood Dowels (3) into the side holes of the Panels (D, E and F).
3
3
3
3
D
E
3
3
3
3
F
2
A
C
B

7
Assembly Instructions
4. Using the wood dowels as a guide, attach the Partition Panels (D and E) to the Bottom Panel (F) and
fasten them in place with four 50 mm Screws (5). Fully tighten the screws with a Phillips screwdriver.
5. Attach the Side Frames (B and C) to the Bottom Panel (F) and Top Front Stretcher (G). Attach the Side
Frames (B and C) into place by engaging the Cam Locks (1).
D
E
5
55
5
F
F
G
B
C
1
1
1
1

8
Assembly Instructions
6. Ask for assistance to lift the assembly upright and proceed to fasten the Top Front Stretcher (G) to both
Side Frames (B and C) by engaging two Cam Locks (1).
7. Glue the Wood Dowers (3) into the top inner holes of the unit. DO NOT inert the wood dowels into the
cam lock holes.
C
B
E
D
1
1
G
C
B
E
D
G
3
333
3
3
3
3
33
3
3

9
Assembly Instructions
8. Place the Top Panel (A) onto the inserted Wood Dowel (3) making sure the back egdes are even with
each panels. Attach the Top Panel (A) in place by engaging the Cam Locks (1).
9. Now, go back and tighten all cam locks. Make sure that all the parts are tight and there are no gaps
between the pieces. This will help keep the unit square. Ask for assistance to lay down the unit at its
front edge as shown.
10. Unfold the Back Panel (L) and lay it to the back edges of the assembled unit so that the drilled holes on
the Back Panel overlap the pilot holes on the Top Panel (A) properly. Fasten the Back Panel (L) into
place with the provided Washer Head Screws (4).
NOTE: We recommend attaching back panel with the washer head screws at the corners first.
A
C
B
E
D
G
A
1
4
L
C

10
Assembly Instructions
11. Securely screw two Center Supports (H) into the threaded inserts on the Bottom Panel (F).
12. Ask for assistance to lift the assembly unit upright.
13. Insert the Shelf Supports (10) into the desired holes in the sides of each compartment. Make sure you
place the four Shelf Supports (10) in the same level so the shelf is not tilted. Tilt and set the Adjustable
Shelves (J and K) onto the Shelf Supports (10). Secure the shelves in place with the 12 mm Screws (12)
for extra support.
F
CH
H
J
KJ
A
B
C
DE
J/K
10
12