Whalen WHA-10005 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2019-09-16 Rev. 0001-A
Gaming Desk
Model # WHA-10005
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Gaming Desk
MODEL # WHA-10005
MADE IN CHINA
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging
material before discarding carton. Remove any remaining staples from the carton before
discarding. Remove all parts from carton and separate into groups as indicated on part
list. Please ensure all parts are included prior to assembly. Use of power tools to
complete assembly is not recommended.
M A X I M U M R E C O M M E N D E D W E I G H T L O A D S
MAXIMUM LOAD 22.7 kg / 50 lb.
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 90.8 kg / 200 lb.

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and
non-abrasive surface. You will need the parts identified on page 6 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH THE DOWELS. EXCESS GLUE CAN BE
WIPED OFF WITH A DAMP CLOTH.
Insert dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the KD unit.
GLUE
XX
FINAL
1 2 43

4
FURNITURE POWER DISTRIBUTION CENTER
IMPORTANT SAFETY INSTRUCTIONS
Carefully read all instructions before installing and operating fixture
IF YOU HAVE ANY QUESTIONS REGARDING THE PROPER INSTALLATION
CONSULT A QUALIFIED ELECTRICIAN.
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR
INJURY TO PERSONS, PLEASE FOLLOW THE BELOW:
 Use only insulated staples or plastic ties to secure the cords.
 Route and secure cords so that they will not be pinched or damaged when the desk is pushed to the wall.
 Make sure cord is not pinched between desk and floor.
 Use the unit for indoor use only.
 Do not use an extension cord to connect this unit to a wall outlet.
 Use a power strip with surge protection to supply power to other electrical devices in desk.
 This unit must be plugged into a properly grounded outlet.
 The socket-outlet should be installed near the equipment and should be easily accessible.
 Maximum load of connected equipment cannot exceed a total of 12 amps and 120 volts.
 Do not open or disassemble this unit for any reason.
SAVE THESE INSTRUCTIONS

5
Furniture Power Distribution Unit User Guide
Please read this user guide before installing and using your power distribution Center.
INTRODUCTION
The integrated power and USB center offers 480 Mbps
high transmission rate and can connect up to two devices,
such as a digital camera, MP3 player, cell phone or
wireless mouse.
SPECIFICATIONS
cULus listed, rated for: 120 V ac, 12 A, 60 Hz
NOTES
 To reach USB 2.1 high speed, your computer or host
adapter card must support USB 2.1. This hub is also
backwards compatible with USB 1.1.
 When using the hub with a computer that has a version
1.1 USB interface, all of the devices attached to the hub
will run at USB 1.1 speed.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician
for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
CAN ICES-3 (B)/NMB-3(B)
This Class B digital apparatus complies with Canadian
ICES-003.
Whalen Furniture Manufacturing
1578 Air Wing Road
San Diego, CA 92154, USA
1-866-942-5362
WARNINGS
! Your hub automatically shuts off any port with a low
or excessive current.
! If USB Hub Current Limit Exceeded appears on your
screen, disconnect the affected USB device, click
Reset on the screen, and reconnect the device.
! If one of your hub ports is disabled, but USB Hub
Current Limit Exceeded does not appear:
 Disconnect and reconnect the affected device.
 If the port still does not work, disconnect the hub
and the device, and then reconnect.
! Keep your desktop hub dry; if it gets wet, wipe it dry
immediately.
! Do not modify or tamper with your desktop hub’s
internal components. It may cause a malfunction and
invalidate its warranty.
! Modifications not approved by the party responsible
for compliance could void user’s authority to operate
the equipment.
Product: Furniture Power Distribution Unit
Model No: HG3000-DBU
Company: Whalen Furniture Manufacturing

6
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Desk Top (Qty. 1) B- Fixed Shelf (Qty. 1) C- Back Panel (Qty. 1)
D- Small Leg (Qty. 4) E- Large Leg (Qty. 2) F- Partition Panel (Qty. 2)
G- Bottom Panel (Qty. 2) H- Adjustable Shelf (Qty. 1) I- Cup Holder (Qty. 1)
J- Accessory Hook (Qty. 1) K- Cable Wheel (Qty. 2) L- Power Center (Qty. 1)
(1) Cam Lock (2) Cam Bolt (3) M6 x 30 mm Wood Dowel (4) M4 x 32 mm Screw
(Qty. 4+1 extra) (Qty. 4+1 extra) (Qty. 2+1 extra) (Qty. 4+1 extra)
(5) 1/4" x 5/8" Bolt (6) Lock Washer (7) Flat Washer (8) 1/4" x 1 1/8" Bolt
(Qty. 29+1 extra) (Qty. 29+1 extra) (Qty. 29+1 extra) (Qty. 8+1 extra)
(9) M3.5 x 15 mm Screw (10) Shelf Pin with Shoulder (11) Shelf Pin (12) Floor Leveler
(Qty. 6+1 extra) (Qty. 2+1 extra) (Qty. 2+1 extra) (Qty. 4+1 extra)
Glue (Qty. 1) Hex Wrench (Qty.1)
Tools required: Hex wrench (included), rubber mallet and Phillips screwdriver (not included).

7
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (2) into the threaded bushing on the Desk Top (A) using a Philips
screwdriver.
② x 4
2
A

8
Assembly Instructions
3. Insert two Wood Dowels (3) into the side holes of the Back Panel (C). Make sure that you use a small
amount of glue with both ends of all dowels.
③ x 2
3
33
3
C

9
Assembly Instructions
4. Align and attach the Back Panel (C) to the Desk Top (A) by engaging four Cam Locks (1) (Refer to
page 3 on Cam Lock system operation supplement).
① x 4
1
A
C
C
A

10
Assembly Instructions
5. Feed the wire of Power Center (L) through the cutout of the Back Panel (C) and push into the cutout.
Secure it in place with two 15 mm Screws (9). Make sure the wire is not pinched.
⑨ x 2
L
CC
9
L
9

11
Assembly Instructions
6. Ask for assistance to stand the assembled Desk Top (A) vertical.
7. Align and attach the Fixed Shelf (B) to the assembled Back Panel (C) with four 32 mm Screws (4) and
securely tighten with a Philips screwdriver.
④ x 4
B
A
C
4
4
4
4

12
Assembly Instructions
8. Fit the previous assembly between the Large Legs (E). Making sure the mounting holes of metal tabs
overlap the threaded inserts underneath the Desk Top (A) and the Fixed Shelf (B).
B
A
E
E

13
Assembly Instructions
9. Fasten the Desk Top (A) and the Fixed Shelf (B) into place with eight 5/8" Bolts (5) and eight Washers
(6 and 7).
B
A
E
E
5
6
7
⑤ x 8 ⑥ x 8 ⑦ x 8

14
Assembly Instructions
10. Fit the return of Small Legs (D) onto U-shaped brackets of Large Legs (E) and fasten them into place
with four 5/8" Bolts (5) and four Washers (6 and 7).
⑤ x 4 ⑥ x 4 ⑦ x 4
D
D
D
D
E
E
B
E
D
5
6
7

15
Assembly Instructions
11. Fasten the Small Legs (D) to the Fixed Shelf (B) with four 5/8" Bolts (5) and four Washers (6 and 7).
⑤ x 4 ⑥ x 4 ⑦ x 4
B
D
DD
D
5
6
7

16
Assembly Instructions
12. Align and attach the Bottom Panels (G) to the Legs (D and E) with eight 5/8" Bolts (5) and eight
Washers (6 and 7).
⑤ x 8 ⑥ x 8 ⑦ x 8
D
D
E
E
5
6
7
G
G
D
D

17
Assembly Instructions
13. Insert the Partition Panels (F) to against the Small Legs (D). Make sure that the mounting holes on
Small Legs (D) align with the threaded inserts on Partition Panels (F) properly.
F
F

18
Assembly Instructions
14. Fasten the Partition Panels (F) into place with eight 1 1/8" Bolts (8).
⑧ x 8
8
F
F
D
D
D
D
D
F

19
Assembly Instructions
15. Align and attach the Cup Holder (I) and the Accessory Hook (J) to the Fixed Shelf (B) with five 5/8"
Bolts (5) and five Washers (6 and 7).
⑤ x 5 ⑥ x 5 ⑦ x 5
5
B
I
/J
B
6
7

20
Assembly Instructions
16. Attach the Floor Levelers (12) to the bottom of the Small Legs (D).
x 4
12
D
12
12
12 D
D
D