Whalen Asher Series User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2016-11-09 Rev. 0001-B Factory: HOAJOI
Asher 2pk Saddle Stools
Stock # ASH2PKST
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [email protected]
LOT NUMBER:
DATE PURCHASED: /
/

2
1. Maximum load weight on stool is 136 kg (300 pounds).
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware and parts out of the reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all bolts and screws are tightly fastened before the unit is used.
6. Check that all bolts and screws are tight at least every 3 months or as needed.
7. Use the long end of the T-handle wrench to fasten bolts loosely and quickly.
8. Use the short end of the T-handle wrench for final tightening.
MAXIMUM RECOMMENDED WEIGHT LOADS
GENERAL INFORMATION, TIPS AND TRICKS
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
②
①

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A - Seat Frame with Cushion (Qty. 2)
B - Left Front/Right Back Leg (Qty. 4) C - Right Front/ Left Back Leg (Qty. 4)
D- Long Stretcher (Qty. 4) E - Short Stretcher (Qty. 4)
(1) M8 x 60 mm Bolt (2) Lock Washer (3) Flat Washer
(Qty. 16+1 extra) (Qty. 16+1 extra) (Qty. 16+1 extra)
(4) M4 x 50 mm Screw T-handle Hex Wrench Touch-up Pen
(Qty. 16+1 extra) (Qty. 1) (Qty. 1)
Tools required: Hex wrench (provided) and Phillips screwdriver (not provided).

4
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Attach the Short Stretcher (E) between the Legs (B and C) with the tenons fully inserted. Make sure that
the slant holes on the stretcher will face the floor when the unit is turned upright.
3. Lay one Seat Frame (A) upside down on a smooth and protective surface.
4. Fit the leg assembly to the corners of the Seat Frame (A). Insert four 60 mm Bolts (1) with Lock Washers
(2) and Flat Washers (3) through the drilled holes on the corner blocks and screw into the threaded inserts
on the Legs (B and C).
NOTE: DO NOT fully tighten all the bolts until the unit has been adjust and all the legs are levelled so
that they do not wobble. Once adjusted, go back and tighten while making sure that the unit remains level.
DO NOT fully tighten the bolts initially until all the bolts are ready to assemble.
To avoid causing damages to the thread, DO NOT over-tighten the bolts.
M8 x 60 mm Bolt
(4 used in this step) ①Flat Washer
(4 used in this step)
③
Lock Washer
(4 used in this step)
②

5
Assembly Instructions
5. Insert the tenon of two Long Stretchers (D) into the mortises of the Legs (B and C). Make sure that the
slant holes on the Long Stretchers will face the floor when the unit is turned upright.
6. Repeat the same procedure to attach the other leg assembly at the opposite end.
NOTE: DO NOT fully tighten the bolts.
M8 x 60 mm Bolt
(4 used in this step) ①Flat Washer
(4 used in this step)
③
Lock Washer
(4 used in this step)
②

6
Assembly Instructions
7. Insert and screw eight 50 mm Screws (4) into the slant holes in the Stretchers (D and E). Tighten the
screws with a Phillips screwdriver.
8. Stand the assembled unit upright on a flat surface. Press down the Seat Cushion (A) to even all legs. Now,
tightly fasten all bolts with the provided hex wrench.
9. Repeat the same process to assemble the other stool.
M4 x 50 mm Screw
(8 used in this step) ④

7
Care and Maintenance
 Use a soft, clean cloth that will not scratch the surface when dusting.
 Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
 Using solvents of any kind on your furniture may damage your furniture’s finish.
 Never use water to clean your furniture as it may cause damage to the finish.
 Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing.
 Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
 Check bolts/screws periodically and tighten them if necessary.
Further Advice about Wood Furniture Care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
A Touch-up Pen has been provided to repair any small nicks or scratches that may occur during
assembly or shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!

ESTE INSTRUCTIVO CONTIENE INFORMACIÓN IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y MANTENGA PARA USO FUTURO.
Fecha 2016-11-09 Rev. 0001-B Fábrica: HOAJOI
Taburetes Silla de Montar Asher de 2pcs
Modelo # ASH2PKST
ENSAMBLE REQUERIDO POR ADULTO
Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne este producto a
la tienda donde lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su
instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica:
866-942-5362
Hora Estándar del Pacífico: 8:30 a.m. - 4:30 p.m., de Lunes a Viernes
O visite nuestra página de Internet 24 horas al dia, 7 días a la semana para asistencia
www.whalenstyle.com
O mande un correo electrónico a [e-mail]
LOTE NÚMERO:
FECHA DE COMPRA: /
/

2
1. Máxima carga recomendada en el taburete es de 136 kg (300 libras).
1. Por favor lea el instructivo antes de comenzar el ensamble.
2. Para evitar daños, ensamblar el producto en una superficie fuerte, nivelada y no abrasiva.
3. Mantenga todo el material de ferretería fuera del alcance de niños.
4. Esperar hasta que todos los pasos esten completados antes de apretar los tornillos.
5. Asegurar de que los tornillos y tuercas esten apretados antes de usar la unidad.
6. Revisar que los tornillos y tuercas esten apretados cada 3 meses o como sea necesario.
7. Use el extremo largo de la llave de manija-T para apretar los tornillos flojamente y
rápidamente.
8. Use el extremo corto de la llave de manija-T para un apretón final.
MÁXIMOS PESOS RECOMENDADOS
INFORMACIÓN GENERAL, RECOMENDACIONES Y TRUCOS
ESTA UNIDAD DEBE UTILIZARSE CON LOS PESOS MÁXIMOS
INDICADOS. SI SE EXCEDE EL PESO MÁXIMO, PODRIA RESULTAR EN UNA
INESTABILIDAD DE LA UNIDAD CAUSANDO POSIBLES LESIONES.
②
①