Whalen Montcross MON7PD-E User manual

Whalen Furniture Manufacturing Page 1 Factory No. 15713
Date 2015-03-31 Rev.1 Factory: HOAJOI E
Montcross 7 Piece Dining Set
ITM. / ART. 908722
Model # MON7PD-E
ASSEMBLY INSTRUCTIONS
IMPORTANT, RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362 (English, French and Spanish)
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday
(in the US and Canada only)
Or visit our website www.whalenfurniture.com
Or e-mail your request to [email protected]
LOT NUMBER:
DATE PURCHASED: / /

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 2
E
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or
replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet
your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from State to State.
AUSTRALIA: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure.
Customer Service: 1-866-942-5362 (English, French and Spanish)
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday
(in the US and Canada only)
www.whalenfurniture.com
1. Maximum load weight on chair is 136 kg / 300 lb
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware and parts out of the reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all bolts and screws are tightly fastened before the unit is used.
6. Check that all bolts, screws and knobs are tight at least every 3 months or as needed.
MAXIMUM RECOMMENDED WEIGHT LOADS
THIS UNIT IS INTENDED FOR USE ONLY WITH THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM
WEIGHTS INDICATED MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.
GENERAL INFORMATION, TIPS & TRICKS

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 3
E
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts are present before
beginning assembly.
A - Chair Backrest (2x) B - Seat Frame with Cushion (2x)
C - Left Front Leg (2x) D - Right Front Leg (2x)
E - Left Side Stretcher (2x) F - Right Side Stretcher (2x)
AA- Bolt (4x+1 extra) BB- Bolt (8x+1 extra)
CC- Hex Nut DD- Lock Washer EE- Flat Washer FF- Wood Screw
(8x+1 extra) (20x+1 extra) (20x+1 extra) (8x+1 extra)
Allen Wrench (1x) Open Wrench (1x) Touch-up Pen (1)
Tools required: Allen wrench and open wrench (included) and Phillips screwdriver (not included).

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 4
E
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Remove the plastic caps from the hanger bolts of the Front Legs (C and D) for the following steps.
3. Attach one Left Front Leg (C) to the left front corner block of the Seat Frame (B) by inserting the hanger
bolts through the drilled holes on the corner block and fit the Flat Washer (EE), Lock Washer (DD) and
Hex Nut (CC) onto each hanger bolt. Securely tighten the Nuts with the provided Open Wrench.
NOTE: DO NOT fully tighten all the nuts until the chair has been adjusted and level all the legs so that
they do not wobble. Once adjusted then go back and tighten while making sure that the unit remains level.
4. Repeat the same procedure to attach one Right Front Leg (D) to the right front corner block of the Seat
Frame (B).
DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are
ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the nuts or bolts.
B
CC B
DD
EE
C/D
C/D
C
D

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 5
E
Assembly Instructions
5. Lay one Backrest (A) on a smooth and protective surface with the threaded inserts facing up.
6. Insert the tenon of Left and Right Side Stretchers (E and F) into the mortises of the Backrest (A). Make
sure that the slant holes on the Side Stretchers will face the floor when the unit is turned upright.
7. Attach the assembled Seat Frame (B) to the middle rail of the Backrest (A) and insert both Side Stretchers
(E and F) into the Front Legs (C and D) respectively. Insert Bolts (BB) with the Large Washers (DD and
EE) through the drilled holes on the Seat Frame (B) at rear corner blocks and loosely tighten into the
threaded inserts on the Backrest (A). As shown.
8. Secure the Seat Frame (B) to the Backrest (A) by inserting two Bolts (AA) with the Large Washers (DD
and EE) through the drilled holes on the rear rail of the Seat Frame.
NOTE: DO NOT fully tighten the bolts.
E
F
C
D
B
A
E/F
C/D
EE
AA
DD
B
A
E/F
A
EE
BB
DD

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 6
E
Assembly Instructions
9. Position the assembled unit upside down on the carton or other support surface, as shown.
NOTE: Place a protective cover (like the bubble wrap packing material) over the carton or other support
surface to prevent from scratching.
10. Insert and screw four Wood Screws (FF) into the slant holes in the Side Stretchers (E and F). Tighten the
screws with a Phillips screwdriver.
11. Stand the assembled unit upright on a flat surface. Press down the Seat Cushion (B) to even all legs. Now,
tightly fasten all bolts with the provided Allen Wrench.
12. Repeat the same procedure to assemble the other chairs.
A
E/F
FF
A/C/D
F
C
E
D
B

ITM. / ART. 908722
Whalen Furniture Manufacturing Page 7
E
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting.
Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
Using solvents of any kind on your furniture may damage the finish.
Never use water to clean your furniture as it may cause damage to the finish.
Always use coasters under beverage glasses and flowerpots.
Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create
spotting within the furniture finish.
Stains or marks from crayons or ink markers will be difficult to remove.
In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
Check bolts/nuts periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity
changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from
direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
A touch-up pen has been provided to repair any small nicks or scratches that may occur during
assembly or shipping.
We hope you enjoy your purchase for many years.
Thank you for choosing Whalen Furniture!
www.baysidefurnishings.com
MADE IN VIETNAM / FABRIQUÉ AU VIETNAM / HECHO EN VIETNAM

IF YOU NEED TO REQUEST ANY REPLACEMENT PARTS, PLEASE USE THE LIST BELOW
Montcross 7-pc Dining Set (MON7PD-E)
*MON7PD-E-1-CB Chair Backrest *MON7PD-E-11-TA Tenon Attachment *MON7PD-E-22-M8HN M8 Hex Nut *MON7PD-E-2-SF Seat Frame *MON7PD-E-12-PF Plastic Fitting *MON7PD-E-23-M8x40B M8 x 40 mm Bolt *MON7PD-E-3-SC Seat Cushion *MON7PD-E-13-TTWS Table Top w/Slides *MON7PD-E-24-M8x80B M8 x 80 mm Bolt *MON7PD-E-4-SCS Seat Cushion Screw *MON7PD-E-14-TS Table Stretcher *MON7PD-E-25-M6x90B M6 x 90 mm Bolt *MON7PD-E-5-LSS Left Side Stretcher *MON7PD-E-15-LHS Leaf Hinge w/Screws *MON7PD-E-26-LLW Large Lock Washer *MON7PD-E-6-RSS Right Side Stretcher *MON7PD-E-16-LHS Leaf Holder w/Screws *MON7PD-E-27-LFW Large Flat Washer *MON7PD-E-7-LFL Left Front Leg *MON7PD-E-17-SL Sash Lock *MON7PD-E-28-SFW Small Flat Washer *MON7PD-E-8-RFL Right Front Leg *MON7PD-E-18-LA Leaf Apron *MON7PD-E-29-M4x40WS M4 x 40 mm Wood Screw *MON7PD-E-CHC Complete Hardware for Chair *MON7PD-E-19-LAHS Leaf Apron Hinge w/Screws *MON7PD-E-30-M4AW 4 mm Allen Wrench *MON7PD-E-9-TIL Table Inner Leg *MON7PD-E-20-BGC Ball-style Grab Catches *MON7PD-E-31-OW Open Wrench *MON7PD-E-10-TOL Table Outer Leg *MON7PD-E-21-MB Mounting Board *MON7PD-E-32-TUP Touch-up Pen
*MON7PD-E-CHT Complete Hardware for Table