Wildix W01GSM User manual

Wildix W01GSM Media gateway
Version updated on: 21.07.2015
Quick Start Guide

Overview 3
Specifications 4
Protocols 4
System Functions 4
Industrial Standards Supported 4
General Hardware Specification 4
Installation 5
Step 1 - Install the SIM card 5
Step 2 - Install the Antenna 5
Step 3 - Install the Ethernet connection 5
Provisioning 5
GMS trunk parameters 5
Wildix W01GSM Media gateway - Quick Installation Guide 2

Overview
W01GSM is an IP based GSM Gateway that offers a stable network configuration and an
excellent audio quality. The device supports IEEE 802.3af PoE.
LED Indicator
State
Description
RUN
On
device is booting
Slow blinking
device not registered in WMS
Fast blinking
device registered
GSM
On
device is booting or call in progress
Off
SIM card not registered on GSM network
(incorrect PIN or no coverage)
Slow blinking
SIM card registered
Interface
Description
WAN
WAN indicator blinks if device is connected (even if not registered)
RST
press and hold for more than 6 sec to reset
SIM slot
press yellow button to open the card slot
ANT
3dB external antenna
Wildix W01GSM Media gateway - Quick Installation Guide 3

Specifications
Protocols
• Standard SIP
• NAT
• HTTP, DHCP, DNS
• ITU-T G.711a-Law/μ-Law, G.729AB
System Functions
• PLC, VAD, CNG
• PoE class 3
•Port gain adjustment
• SIM/UIM card encryption
• SMS sending and receiving
• Echo Cancellation (with ITU-T G.168/165 standard)
• Quad band GSM 850/900/1800/1900 MHz
Industrial Standards Supported
• Stationary use environment: EN 300 019: Class 3.1
• Storage environment: EN 300 019: Class 1.2
•Transportation environment: EN 300 019: Class 2.3
•Acoustic noise: EN 300 753
•CE EMC directive 2004/108/EC EN55022:
•2006+A1:2007
•EN61000-3-2: 2006,
•EN61000-3-3: 1995+A1: 2001+A2: 2005
•EN55024: 1998+A1: 2001+A2: 2003
•Certifications: FCC, CE
General Hardware Specification
•Temperature: 0~40 °C (operation) / -20~80 ℃(storage)
•Humidity: 5% ~ 90% RH
•Certifications: FCC, CE
•Power Consumption: Max 10W
•Dimensions: 12 x 9 x 2.4 cm approximately
Wildix W01GSM Media gateway - Quick Installation Guide 4

Installation
Before starting the installation, make sure that there is a DHCP server in your network
environment. Your Ethernet switch should be PoE Class 3 or a Wildix switch.
Online guide to installation, connection and configuration of a Wildix GSM Gateway.
Step 1 - Install the SIM card
Open the SIM card tray and follow these steps:
• Press the yellow button, the SIM tray pops out
• Put the SIM card into the tray and insert the tray it into the card slot
Step 2 - Install the Antenna
Screw the 3dB antenna into the ANT jack plug of the W01GSM gateway.
Antenna with a longer cable is available as separate product (cod. W01GSM-ANT).
Step 3 - Install the Ethernet connection
Connect the WAN interface to the PoE switch
Provisioning
Requirements: GSM SIM card with PIN disabled.
If you are using a WMS integrated DHCP Server, go to Settings →System →DHCP Server
and search for the device on the DHCP leases.
Follow our online guide to provision the media gateway.
For remote/unreachable media gateways behind NAT/Firewall, follow our online guide for
remote provisioning.
GMS trunk parameters
As soon as the gateway appears in the Devices menu, the GSM trunk appears in the Trunks
menu and you can edit the trunk parameters. Follow our online guide.
Each W01GSM connected to the PBX appears on the Trunks page with the current status of
Signal Quality, which is normally updated every 30/60 seconds.
Wildix W01GSM Media gateway - Quick Installation Guide 5