Wildix W01PRI User manual

W01/02PRI Pre 2017 - Quick Installation Guide - English
W01/02PRI Pre 2017 - Quick Installation Guide - English Page 1 of 5
Jun 15, 2020 23:02
W01/02PRI Pre 2017 - Quick Installation Guide - English
Connection to power supply
Connection to Ethernet
Connecting W01/02PRI using DHCP server
Connecting W01/02PRI using a static IP address
Configuration of the gateway
Connection to the line
Reset of the gateway
Mounting racks
Connection to power supply
Connect the gateway using the power supply and the cable provided with the PRI gateway, as it is shown on the
picture:
Connection to Ethernet
The steps below help you to connect and configure your PRI gateway. W01PRI and W02PRI are ISDN
VoIP media gateways offer respectively 30 or 60 voice channels.
Updated: March 2017
Permalink: https://confluence.wildix.com/x/LAg8AQ
Note: W01/02PRI 2017 Installation Guide is published here: .https://confluence.wildix.com/x/5wGIAQ

W01/02PRI Pre 2017 - Quick Installation Guide - English
W01/02PRI Pre 2017 - Quick Installation Guide - English Page 2 of 5
On the rear panel of the gateway there are five network ports:
ETH5 port: used as WAN port
ETH1 – ETH4: used as LAN port
Access via WAN port:
Connect WAN port (ETH5) to the same network as the PBX or an external DHCP server (for instance, its
Router)
As soon as the DHCP server assigns an IP address to the gateway, you can pass to the next step of the
gateway configuration
In case the PBX is used as a DHCP server, the gateway is detected on the network automatically
In case an external DHCP server is used, check the list of the active leases to detect the IP address
assigned to the gateway
Connecting W01/02PRI using DHCP server
Before you start:
Make sure that your network connection is working
You must use an IPv4 Network
The IPv4 Network must have a DHCP server
If you do not have access to the DHCP server's logs, then follow instructions described in Connecting W01
/02PRI using a static IP address
Steps
Connect a 10/100/1000 BaseT Ethernet RJ-45 cable into the ETH1 connector of the device
Connect the other end of the cable to a router/switch connected to your Network
Validate the installation
Turn on the power sources that are used to power the gateway at the circuit breaker
Turn on the power switch of the PRI gateway
Consult the DHCP server's logs to find out your IP address
Result

W01/02PRI Pre 2017 - Quick Installation Guide - English
W01/02PRI Pre 2017 - Quick Installation Guide - English Page 3 of 5
The Power LED on the device will be flashing when the device performs a DHCP server query. It will become
solid once it successfully gets an IP address from the DHCP server. At this point, you can now use the DHCP IP
address to access your device's management interface.
Connecting W01/02PRI using a static IP address
Before you start:
Your network interface must be set with an IP address in the 192.168.0.0/24 subnet (e.g. 192.168.0.11)
You must use an IPv4 Network
Make sure that your network connection is working
Steps
Connect a 10/100/1000 BaseT Ethernet RJ-45 cable into the ETH5ETH5/EXT Ethernet connector of the
device
Connect the other end of the cable into your PC
Validate the installation
Turn on the power sources that are used to power the PRI gateway at the circuit breaker
Turn on the power switch of the PRI gateway
Result
You can now use the 192.168.0.10 IP address to access your device's management interface.
Configuration of the gateway
Follow our to provision the PRI gateway.online Guide
For remote/ unreachable media gateways behind NAT/ Firewall, follow our online Guide about remote
.provisioning
Trunk parameters: Trunk Settings Guide, BRI/ PRI Trunk Settings
Connection to the line
On the rear panel of the gateway, there are one or two modules with an Ethernet port marked as E1/T1 (Slot2
and Slot3).
Connect your PRI line to this port, as it is shown on the picture below:

W01/02PRI Pre 2017 - Quick Installation Guide - English
W01/02PRI Pre 2017 - Quick Installation Guide - English Page 4 of 5
Reset of the gateway
In case you need to reconfigure the gateway, you should perform a reset procedure, as shown on the picture.
The switch marked as “ ” is situated on the rear panel of the gateway.Reset/Default
Use the paper clip or the object of the similar shape to press the button
Hold the button until all the LEDs of the gateway stop blinking and remain turned on (circa 10 seconds)
Release the button and wait for the reboot of the gateway
In case the LEDs remain turned on for more than one minute after the reset procedure, disconnect the power
supply and repeat the reset procedure when the device starts.
Mounting racks
Attach two racks provided with the gateway to the device, as shown on the picture:

W01/02PRI Pre 2017 - Quick Installation Guide - English
W01/02PRI Pre 2017 - Quick Installation Guide - English Page 5 of 5