Wincor Nixdorf BEETLE /?-II Manual

BEETLE /M-II
with Embedded Scale
Controller and 2 Displays
Technical Information

All brand and product names mentioned in this document are trademarks of their respective
owners. The reproduction, transmission or use of this document or its contents is not permitted
without express authority. Offenders will be liable for damages. All rights, including rights created
by patent grant or registration of a utility model or design, are reserved.
Delivery subject to availability; technical modifications possible.
Copyright © Wincor Nixdorf International GmbH, 2005
Published by
Wincor Nixdorf International GmbH
D-33094 Paderborn

BEETLE/ M-II
_____________________________________________________________________
_________________________________________________________________
1
Introduction
The BEETLE /M-II is a newly developed POS system, equipped with
an additional embedded scale controller to which a scale can be
connected.
This module processes all scale data from tare specification to zero
setting.
The embedded scale controller is internally connected to a multiplexer
card VGA/4-MUX PCI so that the scale data can be displayed at the
customer/cashier display BA69. The display BA69W with tare and zero
button must be connected to the LCD2 socket of the multiplexer card.
For security reasons the scanner scale module has a calibration seal at
the backside of the BEETLE /M-II.

BEETLE/ M-II
_____________________________________________________________________
_____________________________________________________________________
2
Interior View
Embedded Scale Controller
Emb. Scale
Controller
HD/FD
Power
Supply
Fan

BEETLE/ M-II
_____________________________________________________________________
_________________________________________________________________
3
VGA/4-MUX PCI-Controller
VGA/4-MUX PCI-Controller
Embedded Scale Controller

BEETLE/ M-II
_____________________________________________________________________
_____________________________________________________________________
4
Backside
S
cale Connection
Calibration
Seal/Calibra-
tion Switch
Connection for COM4
BA69 Display Connection
BA69W-Display-Connection
Connection COM4
to Scale Controller

BEETLE/ M-II
_____________________________________________________________________
_________________________________________________________________
5
Dimensions
Width: 288mm
Height: 155mm
Depth: 286mm (without cable cover)
354mm (with optional cable cover)
Setting up the Device
Set up the BEETLE /M-II POS system so that it is not subject to any
extreme environmental conditions. Protect the device from shocks, dust,
moisture, heat and strong magnetic fields. Always be sure that the side
ventilation slots of the BEETLE /M-II are not blocked, thus ensuring that
the device always has sufficient ventilation. Mind the minimum
clearances indicated below! If you plan to install the unit into a confined
space, always be sure to maintain the specified minimum clearance and
ensure constant air flow for effective ventilation. The immediate ambient
temperature for the system must not exceed 40° C/104° F.
These requirements can be best met, if you do not install the unit into a
completely confined furniture.
The maximum depth of installation can be equal to the entire depth of
the unit including the optionally available cable cover, i.e. 354 mm.
50 mm
50 mm

BEETLE/ M-II
_____________________________________________________________________
_____________________________________________________________________
6
Vertical Installation
The following minimum clearances must also be provided in vertical
mounting into a confined furniture in free convection to ensure sufficient
ventilation:
upwards: 50 mm
downwards: 50 mm
A vertically installed device therefore has to be placed on a rig
(spacer made of non-combustible material) that guarantees sufficient
ventilation and a minimum clearance of 50 mm to the bottom of the
furniture.
A surface made of nonflammable material (e.g. concrete or metal) must
be located underneath the vertically mounted BEETLE.
Install the equipment so, that the side with the fan points upward. This is
the side with the lower number of ventilation slots (see picture).

BEETLE/ M-II
_____________________________________________________________________
_________________________________________________________________
7
When installing the BEETLE M/-II, also make sure that the calibration
seal and calibration switch on the rear side of the device are visible
and readily accessible! If it is accessible from only one side, turn the
device (for example 180 degrees vertically) so that the rear sides point
outwards (to the access side).
Technical Specifications
Footprint
Width
Depth (w/o cable cover)
288 mm
286 mm
Height 155 mm
Weigth approx. 7 kg (depending on the installation)
Weight of battery with panel approx. 930 g
Power consumption (typical) 3A / 5A max.
Line voltage frequency 50 / 60 Hz
Noise generation < 47 dB (A)
Power input ratings 100 –120 V / 2A max.
200 –240 V / 1A max.
Operating temperature
EN 60721-3-3, class 3k3
Environmental test IEC 68 / EN60068
Air temperature: +5° C to +40° C
Humidity: 5% r.h. (1 g/m 3 ) – 85% r.h. (25 g/m 3 )
Temperature fluctuation: 0.5 K/min (max. 7.5K/30 min)
Atmospheric pressure 70 kPa –106 kPa
(70 kPa corresponds to installation approx. 3000m above sea level)
Installation environments with long exposure to the sun should be avoided

BEETLE/ M-II
_____________________________________________________________________
_____________________________________________________________________
8
Storage requirements
EN 60721-3-1, class 1k2
Environmental test IEC 68 / EN60068
Air temperature: +5° C to +40° C
Humidity: 5% r.h. (1g/m 3 ) –85% r.h. (25 g/m 3 ) 0.5 K/min
Temperature fluctuation:0.5 K/min (max. 7.5K/30min)
Transport requirements
EN 60721-3-2, class 2k2
Environmental test IEC 68 / EN60068
Air temperature: -25° C to +60° C
Humidity: 15% r.h. (1 g/m3) – 98% r.h. (32 g/m3)
Temperature fluctuation: -25° C / +25° C

BEETLE/ M-II
_____________________________________________________________________
_________________________________________________________________
9
Manufacturer Certification
This device fulfills the requirements of EU Regulations
89/336/EWG "Electromagnetic Compatibility" and
73/23/EWG "Low Voltage Guidelines".
The device carries the CE logo on its rear side, or the
logo is located on the packaging.

Wincor Nixdorf International GmbH, 2004
D-33094 Paderborn
Order No.: 01750075228C