Wincor Nixdorf BA63 User manual

BA63 USB
Customer Display
Product Manual
Edition January 2004

Copyright© Wincor Nixdorf International GmbH, 2004
The reproduction, transmission or use of this document or its contents is not
permitted without express authority.
Offenders will be liable for damages.
All rights, including rights created by patent grant or registration of a utility model or
design, are reserved.
Delivery subject to availability; technical modifications possible.
Pentium™ is a registered trademark of the Intel Corporation
MS-DOS™, Windows 95™, Windows 98™, Windows NT™ Windows XP™ and Wind-
ows CE™ are registered trademarks of the Microsoft Corporation
BEETLE™ is a registered trademark of Wincor Nixdorf International GmbH

Contents
Manufacturer’s Declaration and Approval .............................1
FCC-Class A Declaration............................................................................1
Tested Safety..............................................................................................2
Notes on Care.............................................................................................2
Warranty .....................................................................................................2
Recycling the BA63.....................................................................................3
General Notes .......................................................................4
Installation of the Connector..................................................6
Tube-based ................................................................................................6
Base/ Rotating Plate ...................................................................................8
Customer Display Control....................................................11
Control Sequences ..............................................................12
Backspace (without deleting) ....................................................................12
Line feed ...................................................................................................12
Carriage return..........................................................................................13
Delete display ...........................................................................................13
Position cursor ..........................................................................................13
Delete to end of line ..................................................................................14
Set country code .......................................................................................14
POS Commands .......................................................................................16
Updating the Firmware ........................................................19
System Connection .............................................................21
Cable Connection ................................................................22
Test Functions .....................................................................23
Test by short-circuiting J0 .........................................................................23
Test by short-circuiting J1 .........................................................................23
Short-circuiting J2 .....................................................................................23
Technical Data.....................................................................24

Manufacturer’s Declaration and Approval
This device fulfills the requirements of the EEC directives
89/336/EEC “Electromagnetic Compatibility”and 73/23/EEC
“Low Voltage Directive”.
Therefore, you will find the CE mark on the back of the device or packaging.
FCC-Class A Declaration
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful inter-ference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense. Modifications not authorized by the
manufacturer may void users authority to operate this device. This class A
digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe A est conforme à la norme NMB-003
du Canada.
Wincor Nixdorf International GmbH (WN) accepts no responsibility for radio
and television reception interference resulting from unauthorized
modifications to the equipment. Furthermore, neither cables nor devices
which have not been approved for use by WN may be connected. The user
shall be held responsible for interference caused in this manner.
Device repairs must be carried out by authorized personnel. All guarantee
and liability claims are automatically excluded if repairs have been carried
out by unauthorized personnel.
1
FCC-CLASS A DECLARATION

Tested Safety
The BA63 USB display has been provided with the
GS-symbol for “Tested Safety”.
In addition, the device has received the UL symbol and cUL
symbol.
Notes on Care
Wipe the customer display with a damp cloth as required. Solvents must not
be used under any circumstances as they may damage the plastic.
Warranty
Wincor Nixdorf generally guarantees a limited warranty engagement for 12
months beginning with the date of delivery. This warranty engagement
covers all those damages which occur despite a normal use of the product.
Damages because of
nimproper or insufficient maintenance,
nimproper use of the product or unauthorized modifications of the product,
ninadequate location or surroundings
will not be covered by the warranty.
For details please consult your contract documents.
TESTED SAFETY
2
geprüftegeprüfte
SicherheitSicherheit

Recycling the BA63
Environmental protection does not begin when
it is time to dispose of the BA63; it begins with
the manufacturer. This product was designed
according to our internal norm “Environmental
conscious product design and development”.
The BA63 is manufactured without the use of CFCs und CCHS and is
produced mainly from reusable components and materials.
The processed plastics can, for the most part, be recycled. Even the
precious metals can be recovered, thus saving energy and costly raw
materials.
Please do not stick labels onto plastic case parts. This would help us to
re-use components and material.
At this time, there are still some parts that are not reusable. Wincor Nixdorf
guarantees the environmentally safe disposal of these parts in a Recycling
Center, which is certified pursuant to ISO 9001.
So don’t simply throw your BA63 on the scrap heap when it has served its
time, but take advantage of the environmentally smart, up-to-date recycling
methods!
Please contact your competent branch office for information on how to
return and re-use devices and disposable materials.
3
RECYCLING THE BA63

General Notes
The BA63 customer display is mainly used in POS installations which are
designed in modular form. It is either securely screwed to the POS keyboard
or installed near it so that it is ideally positioned in the cashier’s field of
vision.
The display is a vacuum florescent display (VFD) with two lines, each with
20 alphanumeric characters. The standard character set and corresponding
country code are implemented. Implementation of VFD technology ensures
that the customer display is ergonomically designed to achieve a high
degree of readability, irrespective of the cashier’s angle of vision.
The display is connected to the point of sale system via a Standard USB
interface. The voltage (5 V DC) is also supplied via this interface. The BA63
works with operating systems that support USB and it has to be connected
to a Root-HUB or a Self powered HUB!
The following two BA63 customer displays are available to meet individual
installation requirements:
BA63 customer display with base/rotating table
GENERAL NOTES
4

Customer display with adapter for tube-based installation
The tube diameter is 40 mm (+ 0,3 mm / - 0,1 mm). The tube is not included
in the delivery.
The connection cables are available in different lengths. Cables have to be
ordered separately and will be delivered separately.
5
GENERAL NOTES

Installation of the Connector
Tube-based
Press the release knob marked with
the arrow in the drawing (1) and
disconnect the hinge from the
customer display (2).
Thread the cable through the
adapter (3) and then through the
hinge (4).
TUBE-BASED
6





Connect the hinge and adapter.
Secure the connector cable in the
strain relief.
The distance between the strain
relief and the tip of the connector
must be 73 mm (±2 mm).
7
TUBE-BASED
73mm +/- 2 mm

Plug the cable connector into the
appropriate socket of the customer
display and plug the adapter/hinge
into the customer display again until
it locks into place.
Base/ Rotating Plate
Press the release knob marked with
the arrow in the drawing (1) and
disconnect the hinge from the
customer display (2).
BASE/ ROTATING PLATE
8



Thread the cable through the base
(3) and then through the hinge (4).
Connect the base and the hinge.
9
BASE/ ROTATING PLATE



Plug the cable connector into the
appropriate socket of the customer
display and plug the base/hinge into
the customer display again until it
locks into place.
A metal bracket of the strain relief is
situated on the bottom side of the
base table. Loosen one of the
screws (see arrow), push the bracket
aside and guide the connector cable
from inward to outward under the
bracket through the recess. Tighten
the screw.
BASE/ ROTATING PLATE
10

Customer Display Control
The customer display is controlled via software. The commands are entered
with the appropriate ESC sequences. The following functions are available:
nThe cursor can be moved to the desired position;
nCharacters resp. areas can be deleted;
nCountry-specific character sets can be selected;
nspecial test functions or communication commands can be performed via
POS commands.
11
CUSTOMER DISPLAY CONTROL

Control Sequences
The customer display operates in VT100 mode, i.e. it emulates a subset of
the VT100 ESC sequences and control bytes. These are illustrated in the
following:
Backspace (without deleting) BS
Line feed LF
Carriage return CR
Delete display ESC [2J
Position cursor ESC [Py;PxH
Delete to end of line ESC [0K
Set country code ESC Rn
Backspace (without deleting)
The BS command (hexadecimal 08) moves the cursor one space to the left.
If there is a character in the position to which the cursor moves, it is not
deleted. This command is ignored if the cursor is already at the very start of
the line.
Line feed
The LF command (hexadecimal 0A) moves the invisible cursor down a line
if it is positioned in one of the first three lines of the display. The column
position remains unchanged.
The position of the cursor remains unchanged if it is already in the last line.
The contents of the last line are copied to the first line and the last line is
deleted.
CONTROL SEQUENCES
12

Carriage return
The cursor is moved to the start of the line in which it is currently positioned
when the CR command (hexadecimal 0D) is entered. The command is
ignored if the cursor is already at the start of the line.
Delete display
The display can be deleted with this ESC sequence. The cursor position
remains unchanged. The ESC sequence is as follows:
Code Hexadezimal
ESC ‘[‘ ‘2’ ‘J’ 1B 5B 32 4A
Position cursor
The cursor position can be defined with this ESC sequence. The cursor is
not visible on the display whilst this is being carried out. The following ESC
sequence (for example) can be implemented:
Code Hexadezimal
ESC ‘[‘ ‘Py’ ; ‘Px’ ‘H’ 1B 5B 31 3B 31 48
The parameters are transferred as ASCII characters and have the following
meaning:
Parameter Meaning
Py This parameter defines the line.
Px This parameter defines the column.
Example
The parameters are to replaced with the following values if you wish to
position the cursor at the very start of the first line:
13
CONTROL SEQUENCES

ESC ‘[‘ ‘1’; ‘1’ ‘H’
If you select 0 for the parameter value, this is interpreted as 1 by the
display. If, on the other hand, you select a value which is greater than the
maximum line and column value, the display will interpret this value as the
maximum value permissible.
The cursor is positioned in the first column of the first line if no parameter
values are entered.
Delete to end of line
This command deletes the characters from the cursor, cursor position
included, to the end of the line. The position of the cursor remains
unchanged.
The ESC sequence is as follows:
Code Hexadezimal
ESC ‘[‘ ‘0’ ‘K’ 1B 5B 30 4B
Set country code
The following ESC sequence is implemented in order to select a
countryspecific character set:
Code Hexadezimal
ESC ‘R’ ‘n’ 1B 52 02
The hexadecimal value n corresponds to the country code and defines the
country-specific character set. The German character set corresponds to
the default setting.
CONTROL SEQUENCES
14

Country code Character set
00 USA
01 France
02 Germany
03 Great Britain
04 Denmark 1
05 Sweden
06 Italy
07 Spain 1
08 Japan
09 Norway
0A Denmark 2
0B Spain 2
0C Latin-America
Furthermore PC code pages which contain additional country-specific
display codes can be selected by ESC R n with the following codes:
Country code Code page Character set Country
30 437 Standard Latin-America
31 850 Latin 1
International,
Scandinavia,
Latin-America
32 852 Latin 2
Hungary, Poland,
Czechia,
Slowakia
15
CONTROL SEQUENCES

Country code Code page Character set Country
33 857 Latin 5/Turkey Turkey
34 858 Latin 1+€ char.
International,
Scandinavia,
Latin-America
35 and 29 866 Latin/Cyrillic Russia
37 862 Latin/Hebrew Israel
36 737 Latin/Greek 2 Greece
38 IBM813 Latin/Greek 2 Greece
63 Katakana Katakana Japan
73 Space Page definable universal
In the appendix all character set tables for BA63 in 5 x 7 matrix display are
indicated.
POS Commands
Write Data Command
Data can be Escape sequences, control characters or data to be issued.
Escape sequences can be "hacked up" (1st part in frame n, 2nd part in
frame n+1).
Command: 02H, 00H, Data Count, Data Bytes
Length max. 32. That is the size of the report. Maximum of reference data to
be transferred: 32-3 = 29 bytes, i.e. when configurating an Escape
sequence "economically" for positioning, a line can be displayed with a
Write Data Command.
Read Config Request
Display identification
Command: 21H, 00H, 00H, .., 00H
CONTROL SEQUENCES
16

Test Request
A self test is performed. This command causes no new enumeration.
Command: 00H, 10H, 00H, .., 00H
Status Request
Status is requested.
Command: 00H, 20H, 00H, .., 00H
Reset Request
A reset causes a new login and thus enumeration of the device with all
sub-devices. Therefore, there is no corresponding response to the Reset
Request.
Command: 00H, 40H, 00H, .., 00H
Read Config Response
Response: Length Byte, Status Byte 0, Status Byte 1,
Status Byte2 (s. Status Response)
“Pn1;Pn2;Pn3;Pn4;Pn5;Pn6;Pn7“
Pn1: type of display (1 digit ASCII, e.g. “2")
Pn2: actual code page (4 digits ASCII, e.g. “0852“)
Pn3: country code (2 digits ASCII, e.g. “02“)
Pn4: number of lines (1 digit ASCII, e.g. “2“)
Pn5: columns/line (2 digits ASCII, e.g. “20“)
Pn6: code page loaded in Space-Page (4 digits
ASCII, e.g. “0850")
Pn7: serial number (10 chars ASCII, e.g.
"N000000001")
Note: Pn6 rsp. Pn7 may be omitted in case the Space Page is empty or no
serial number burnt into the device.
CONTROL SEQUENCES
17