Winmate P Series User manual

Please read this instructions before operating the device and retain them for future reference.
IP69K Stainless P-Series
Panel PC with Conduit Pipe
Intel®Core™i5-7200U Kaby Lake, 2.5 GHz
15”/ 19”/ 21.5”/ 23.8”
Model No. R15IK3S-SPC369-P
R19IK3S-SPM169-P
W22IK3S-SPA369-P
W24IK3S-SPA269-P
Quick Start Guide
Document Version 1.0
Document Part No. 91521110104R

2
IP69K Stainless P-Series Panel PC Quick Start Guide
Contents
Chapter 1: Introduction 6
1.1 Overview 6
1.2 Features 6
1.3 Package Content 7
1.4 Product Overview 8
1.5 Physical Buttons 10
1.6 Air Vent Valve 10
1.7 Wi-Fi Antenna 11
1.8 Connector Description 12
Chapter 2: Installation 13
2.1 Mounting 13
2.1.1 VESA Mount 13
2.1.2 Yoke Mount 14
2.1.3 Panel Mount 14
2.2 I/O Cover and Conduit Pipe Installation 15
2.3 Conduit Pipe Removal 17
2.4 Wiring Requirements 17
2.5 Wiring Diagram 18
2.6 Connector Pin Assignments 19
2.6.1 Power Connector 19
2.6.2 HDMI Connector 19
2.6.3 RJ45 Connector 20
2.6.4 USB Connector 20
2.6.5 Serial Port Connector 20
Chapter 3: Getting Started 21
3.1 Connecting to Power Source 21
3.1.1 Connecting to AC Power Source 21
3.1.2 Connecting to DC Power Source (Optional) 22
3.2 Turning On/ Off the Device 22
3.3 How to Enable Watchdog 23
Chapter 4: Maintenance and Troubleshooting 24
4.1 Cleaning the Monitor 24
4.2 Basic Troubleshooting 24
Appendix 25
Appendix A: Hardware Specifications 25
Appendix B: Winmate Software Development Kit 26
Appendix C: Yoke Mount Stand Kit Dimensions 26

3
Chapter 1: Introduction
FCC Statement
This device complies with part 15 FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received
including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a class "B" digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at him own expense.
European Union
Electromagnetic Compatibility Directive (2014/30/EU)
EN55024: 2010/ A1: 2015
oIEC61000-4-2: 2009
oIEC61000-4-3: 2006+A1: 2007+A2: 2010
oIEC61000-4-4: 2012
oIEC61000-4-5: 2014
oIEC61000-4-6: 2014
oIEC61000-4-8: 2010
oIEC61000-4-11: 2004
EN55032: 2012/AC:2013
EN61000-3-2:2014
EN61000-3-3:2013
Low Voltage Directive (2014/35/EU)
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:2013
This equipment is in conformity with the requirement of the following EU legislations and
harmonized standards. Product also complies with the Council directions.

4
IP69K Stainless P-Series Panel PC Quick Start Guide
Copyright Notice
No part of this document may be reproduced, copied, translated, or transmitted in any form or
by any means, electronic or mechanical, for any purpose, without the prior written permission
of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer
Winmate Inc. reserve the right to make changes, without notice, to any product, including
circuits and/or software described or contained in this manual in order to improve design
and/or performance. We assume no responsibility or liability for the use of the described
product(s) conveys no license or title under any patent, copyright, or masks work rights to
these products, and make no representations or warranties that these products are free from
patent, copyright, or mask work right infringement, unless otherwise specified. Applications
that are described in this manual are for illustration purposes only. We make no representation
or guarantee that such application will be suitable for the specified use without further testing
or modification.
Warranty
Winmate Inc. warranty guarantees that each of its products will be free from material and
workmanship defects for a period of one year from the invoice date. If the customer discovers
a defect, we will, at his/her option, repair or replace the defective product at no charge to the
customer, provide it is returned during the warranty period of one year, with transportation
charges prepaid. The returned product must be properly packaged in its original packaging to
obtain warranty service. If the serial number and the product shipping data differ by over 30
days, the in-warranty service will be made according to the shipping date. In the serial
numbers the third and fourth two digits give the year of manufacture, and the fifth digit means
the month (e. g., with A for October, B for November and C for December).
For example, the serial number 1W17Axxxxxxxx means October of year 2017.
Customer Service
We provide a service guide for any problem by the following steps: First, visit the website of
our distributor to find the update information about the product. Second, contact with your
distributor, sales representative, or our customer service center for technical support if you
need additional assistance.
You may need the following information ready before you call:
Product serial number
Software (OS, version, application software, etc.)
Description of complete problem
The exact wording of any error messages
In addition, free technical support is available from our engineers every business day. We are
always ready to give advice on application requirements or specific information on the
installation and operation of any of our products.

5
Chapter 1: Introduction
Advisory Conventions
Four types of advisories are used throughout the user manual to provide helpful information or
to alert you to the potential for hardware damage or personal injury. These are Notes,
Important, Cautions, and Warnings. The following is an example of each type of advisory.
Note:
A note is used to emphasize helpful information
Important:
An important note indicates information that is important for you to know.
Caution A Caution alert indicates potential damage to hardware and explains how to
avoid the potential problem.
Attention Une alerte d’attention indique un dommage possible à l’équipement et
explique comment éviter le problème potentiel.
Warning! An Electrical Shock Warning indicates the potential harm from electrical
hazards and how to avoid the potential problem.
Avertissement! Un Avertissement de Choc Électrique indique le potentiel de chocs
sur des emplacements électriques et comment éviter ces problèmes.
Safety Information
Warning! Always completely disconnect the power cord from your chassis whenever
you work with the hardware. Do not make connections while the power is on. Sensitive
electronic components can be damaged by sudden power surges. Only experienced
electronics personnel should open the PC chassis.
Avertissement ! Toujours débrancher le cordon d’alimentation du chassis lorsque
vous travaillez sur celui-ci. Ne pas brancher de connections lorsque l’alimentation est
présente. Des composantes électroniques sensibles peuvent être endommagées par
des sauts d’alimentation. Seulement du personnel expérimenté devrait ouvrir ces
chassis.
Caution Always ground yourself to remove any static charge before touching the
CPU card. Modern electronic devices are very sensitive to static electric charges. As a
safety precaution, use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded bag when they are not in
the chassis.
Attention Toujours verifier votre mise à la terre afin d’éliminer toute charge statique
avant de toucher la carte CPU. Les équipements électroniques moderns sont très
sensibles aux décharges d’électricité statique. Toujours utiliser un bracelet de mise à
la terre comme précaution. Placer toutes les composantes électroniques sur une
surface conçue pour dissiper les charge, ou dans un sac anti-statique lorsqu’elles ne
sont pas dans le chassis.
Alternating Current !The Protective Conductor Terminal (Earth Ground) symbol
indicates the potential risk of serious electrical shock due to improper grounding.
Mise à le terre ! Le symbole de Mise à Terre indique le risqué potential de choc
électrique grave à la terre incorrecte.

6
IP69K Stainless P-Series Panel PC Quick Start Guide
Chapter 1: Introduction
1.1 Overview
Congratulations on purchasing Winmate® IP69K Stainless P-Series Panel PC.
Winmate P-Series Panel PC features with a waterproof conduit pipe for added cable protection.
The IP69K series is built to withstand extensive wash downs with corrosion resistance against
cleaning agents, especially against close-range high-pressure, high temperature wash downs.
The level of protection allows for easy cleaning and sterilization using water with temperatures
of up to 80°C and pressure of up to 30 Bar. A custom-built waterproof conduit pipe was also
provided for the customer with a cover plate, allowing for an additional layer of protection for
the cables.
1.2 Features
The IP69K Stainless P-Series Display features:
15/ 19/ 21.5/ 23.8” LCD screen with projected capacitive multi-touch
Intel® Core™ i5-7200U Kaby Lake, 2.5 GHz
Full IP69K waterproof enclosure, good corrosion resistance
Conduit pipe for additional cable protection
Air vent valve
Sleek bezel design with round corners
SUS304 stainless steel for food and chemical industries
Multiple mounting options: panel mount, yoke and VESA

7
Chapter 1: Introduction
1.3 Package Content
Carefully remove the box and unpack your device. Please check if all the items listed below
are inside your package. If any of these items are missing or damaged contact us immediately.
Factory shipment list:
Panel PC
Quick Start Guide
(Hardcopy)
AC Adapter
Varies by product specifications
Part No. 91521110104R
50W: 90PO12800000
Open Wire Cable for
Phoenix Connector
(Optional for 9~36V DC)
Waterproof
Conduit 1.5m
Conduit Elbow
Part No. 94EL03L030E1
Part No. 9B000000011I
Part No. 9B000000011J
Yoke Mount Stand Kit
(Optional)
D-sub to RJ45 adapter
15" Part No. 98K015A0000D
19" Part No. 98K019A00002
21.5" Part No.98K021A00001
23.8" Part No.98K023A00001
D-sub 9pin (M) to RJ45
Part No. 601100090000
D-sub 9pin (F) to RJ45
Part No. 601200090001

8
IP69K Stainless P-Series Panel PC Quick Start Guide
1.4 Product Overview
This section contains mechanical drawing of the IP69K Stainless P-Series Panel PC. Notice
that this is a simplified drawing and some components are not marked in detail.
Note 1: Yoke mount stand kit is an optional accessory.
Note 2: Wi-Fi antenna is an optional feature
15”, R15IK3S-SPC369-P Unit: mm
Dimensions: 356 x 280 x 56 mm
19”, R19IK3S-SPM169-P Unit: mm
Dimensions: 445 x 370 x 56 mm

9
Chapter 1: Introduction
21.5”, W22IK3S-SPA369-P Unit: mm
Dimensions: 531 x 322 x 56 mm
23.8”, W24IK3S-SPA269-P Unit: mm
Dimensions: 600 x 369 x 56 mm

10
IP69K Stainless P-Series Panel PC Quick Start Guide
1.5 Physical Buttons
The P-Series Panel PC has one Power physical button located on the rear side. Press the Power
button to power on or power off the device.
1.6 Air Vent Valve
The P-Series Panel PC has an air vent valve that has an automatic mechanical system that
controls and maintains pressure without the assistance of an operator. The air vent valve is a
safety device that discharges air in order to avoid air related problems.

11
Chapter 1: Introduction
1.7 Wi-Fi Antenna
The panel PC has Wi-Fi antennas located on the top.
Note:
Notice that Wi-Fi antennas is an optional feature based on your order.

12
IP69K Stainless P-Series Panel PC Quick Start Guide
1.8 Connector Description
Terminal interfaces are located under the protection cover on rear side of the panel PC. To
access the I/O connectors, please open the protection cover first.
Note:
Notice that input and output connectors vary by product size and specifications.
Connector description:
Item
Description
Terminal Block 3 Pin (Optional) –Provides power to the panel PC, accepts
12V DC or 9V DC to 36V DC power input based on your order specifications.
HDMI - Transmits and protects copyrighted digital video and audio.
Example: An HD tuner to an HD ready TV.
RS-232/422/485 –Serial interface connector controls/monitors devices and
offers in addition digital inputs/outputs.
Example: A printer or scanner to panel PC.
USB 3.0 - Connects USB 3.0 compatible devices to panel PC.
Example: A printer to HMI device.
RJ45/ PoE –Connects the panel PC device to Ethernet network.

13
Chapter 2: Installation
Chapter 2: Installation
Follow this quick installation procedure:
1. Mount your panel PC according to your application requirements (VESA, Yoke, Panel
mount).
2. Connect all the cables to the panel PC.
3. Install I/O protection cover.
4. Route cables through waterproof conduit pipe. And then fix the conduit pipe to the panel
PC.
5. To ensure enclosure rating protection make sure the conduit pipe is firmly fixed and
tightened.
2.1 Mounting
The IP69K Stainless P-Series Panel PC devices come with different mounting options suitable
for most of the industrial and commercial applications.
2.1.1 VESA Mount
The panel PC has VESA mount holes on the rear side. Follow instructions below to mount the
unit with VESA Mount bracket (not supplied by Winmate).
Size
VESA Plate Dimensions
Screw Hole Diameter
15”, 19”
100 x 100 mm
VESA M4x5 mm
21.5”
100 x 100 mm
VESA M4x5 mm
23.8”
100 x 100 mm
VESA M4x5 mm
Installation Instruction
1. Screw VESA bracket to the fixture (ex. swing arm) with four VESA screws.
2. Place the device on VESA bracket.

14
IP69K Stainless P-Series Panel PC Quick Start Guide
2.1.2 Yoke Mount
Yoke Mount solution allows installing the panel PC on the bracket (Optional accessory by
Winmate).
Installation instruction
1. Place the panel PC on the bracket stand, aiming screw holes for each other.
2. Secure screws to fix the device upon the bracket stand.
3. Firmly secure the locking handle to the panel PC.
Yoke Mount Stand Kit is available for order from Winmate. Please check mechanical drawing
in Appendix C of this quick start guide.
For 15" Part No. 98K015A0000D
For 19" Part No. 98K019A00002
For 21.5" Part No. 98K021A00001
For 23.8" Part No. 98K023A00001
2.1.3 Panel Mount
Panel Mount solution is suitable for applications where the panel PC should be embedded
inside the machine/ cabinet.
Caution When mounting on the machine/ cabinet, consider the space between the
panel PC and the wall/ panel required for waterproof conduit.
Attention Lors du montage sur le mur ou à l'intérieur du panneau, tenez compte
de l'espace entre l'écran et le mur / panneau requis pour les conduits étanches.
Size
Cutout Dimensions
Screw Specifications
15”
338 x 262 mm
M3 x 4mm, 12 pcs
19”
427 x 352 mm
M3 x 4mm, 12 pcs
21.5”
513 x 304 mm
M3 x 4mm, 12 pcs
23.8”
582 x 351 mm
M3 x 4mm, 12 pcs

15
Chapter 2: Installation
Installation instruction
❶Make a cutout on the fixture (ex. cabinet)
according to the cutout dimension of the panel
PC. Note: All installation processes will be
done from the rear side of the fixture.
❷Based on the drawing mark screw holes
on a rear side of the fixture. Place the panel
PC on the fixture from the front side. The
sides of the bezel should be visible from
outside.
❸Install washers and use electric
screwdriver to fasten twelve M3 x 4mm
screws from the rear side of the panel PC.
❹Installation complete. Now you can
connect cables and install I/O cover and
waterproof conduit pipe.
2.2 I/O Cover and Conduit Pipe Installation
The unit is available with I/O cover and waterproof conduit pipe for connectors and cable
protection (required to maintain enclosure protection rating). Conduit pipe is a part of a
complete assembly. The conduit pipe protects cables and gives users flexibility in selection of
data, video, and power cables, depending on customer needs.

16
IP69K Stainless P-Series Panel PC Quick Start Guide
Caution The I/O cover and waterproof conduit pipe required to maintain enclosure
protection rating.
Attention Le couvercle et le tuyau de conduit imperméable requis pour maintenir le
degré de protection du boîtier.
Conduit Pipe Components
Before you start installing the pipe, be sure that you have the following components:
Item
Description
Slip Nut
To secure “L” fitting adaptors.
O-Ring Rubber / Gasket
To maintain the IP Rating between equipment and cable.
Conversion reducers
To convert thread forms and size between equipment and cable entry devices.
Locknuts
To secure adaptors / reducers, and stopper plugs into equipment.
Conduit Elbow
To protect cables when installed in confined spaces where the cable may be
bending. This threaded 90-degree bends are available with male connection
threads.
Installing the Conduit Pipe
1. Insert the slip nut followed by the O-ring rubber/ gasket into the tube.
2. Adjust the location of O-ring rubber and pull the slip nut into the O-ring rubber and tighten
up to ensure the waterproof seal.
3. Install the conversion reducers.
4. Place the threaded 90-degree bends into the slip nut and then fasten it.

17
Chapter 2: Installation
To install I/O cover and Conduit Pipe
1. Connect cables to connectors. Conduit assembly may include all possible cables that might
be needed. If not all cables are needed, they may be cut and removed from the conduit
before installation.
2. Position the I/O cover on the rear of the panel PC with the Conduit Elbow pointing towards
the center of the panel PC.
3. Install the provided ten sealing screws and tighten evenly.
4. Install other conduit pipe end in an equipment enclosure suitably rated for application
environment.
2.3 Conduit Pipe Removal
Removal Instructions
1. Firmly hold the elbow twist grip with one hand.
2. Twist the elbow counterclockwise.
3. Pull the conduit out from the elbow.
2.4 Wiring Requirements
The following common safety precautions should be observed before installing any electronic
device:
Strive to use separate, non-intersecting paths to route power and networking wires. If
power wiring and device wiring paths must cross make sure the wires are perpendicular
at the intersection point.
Keep the wires separated according to interface. The rule of thumb is that wiring that
shares similar electrical characteristics may be bundled together.
Do not bundle input wiring with output wiring. Keep them separate.
When necessary, it is strongly advised that you label wiring to all devices in the system.
Do not run signal or communication wiring and power wiring in the same conduit. To
avoid interference, wires with different signal characteristics (i.e., different interfaces)
should be routed separately.
Be sure to disconnect the power cord before installing and/or wiring your device.
Verify the maximum possible current for each wire gauge, especially for the power cords.
Observe all electrical codes dictating the maximum current allowable for each wire gauge.
If the current goes above the maximum ratings, the wiring could overheat, causing
serious damage to your equipment.
Be careful when handling the unit. When the unit is plugged in, the internal components
generate a lot of heat which may leave the outer casing too hot to touch.

18
IP69K Stainless P-Series Panel PC Quick Start Guide
2.5 Wiring Diagram
This P-Series Panel PC has waterproof conduit pipe and I/O cover to ensure protection rating.
Please connect cables first, and then install I/O cover and conduit pipe.
Wiring Diagram
Note:
Please use RJ45 to D-Sub9 Adapter to connect Serial Interfaces cable to P-Series Panel
PC.

19
Chapter 2: Installation
2.6 Connector Pin Assignments
This P-Series Panel PC is equipped with power connector, HDMI connector and USB connector
for touch. The pin assignments of the connectors are described in this section.
2.6.1 Power Connector
By default the P-Series Display has one 3-pin terminal block connector (phoenix type) power
connector that accepts 12V DC or 9~36V DC power input based on your order.
Pin assignment and signal name of the 12V DC power connector
Pin assignment and signal name of the 9Vto 36V DC power connector
2.6.2 HDMI Connector
The P-Series Panel PC has one HDMI1.4a connector for video and audio. Plug HDMI signal
cable to the HDMI connector on the rear side of PC system, and plug the other end to the
monitor.
Pin Assignment and signal names for HDMI1.4a connector
Voltage
Minimum Voltage 11.4V
Maximum Voltage 12.6V
Maximum Current 4.2A
Voltage
Minimum Voltage 9V
Maximum Voltage 36V
Maximum Current 6.6A
Pin №
Signal Name
Pin №
Signal Name
1
HDMI_RX2+
2
GND
3
HDMI_RX2-
4
HDMI_RX1+
5
GND
6
HDMI_RX1-
7
HDMI_RX0+
8
GND
9
HDMI_RX0-
10
HDMI_RXC+
11
GND
12
HDMI_RXC-
13
HDMI_CON_CEC
14
NC
15
HDMI_CON_SCL
16
HDMI_CON_SDA
17
GND
18
+5V_HDMI
19
HDMI_CON_HP

20
IP69K Stainless P-Series Panel PC Quick Start Guide
2.6.3 RJ45 Connector
The panel PC has two RJ45 connectors that support 10/100/1000 Mbps Ethernet
interface for connecting to the internet.
Pin assignment and signal names of Ethernet connector
2.6.4 USB Connector
The panel PC has two USB 3.0 connectors. Use USB cable to connect mouse,
printer or other external devices to your Panel PC.
Pin assignment and signal names of USB 3.0 connector
2.6.5 Serial Port Connector
Use COM1 serial port connector to connect your Panel PC to external devices such
as mouse, modem or printer. You can configure serial port settings via jumpers
located on the motherboard.
Pin assignment and signal names of serial port connector
Pin №
Signal Name
Pin №
Signal Name
1
TX1+
2
TX1-
3
TX2+
4
TX2-
5
TX3+
6
TX3-
7
TX4+
8
TX4-
Pin №
Signal Name
Pin №
Signal Name
1
+5V
2
USB_D-
3
USB_D+
4
GND
5
STDA_SSRX-
6
STDA_SSRX+
7
GND_DRAIN
8
STDA_SSTX-
9
STDA_SSTX+
Pin №
RS-232
RS-422
RS-485
1
DCD
TxD-
D-
2
RXD
TxD+
D+
3
TXD
RxD+
NC
4
DTR
RxD-
NC
5
GND
GND
GND
6
DSR
NC
NC
7
RTS
NC
NC
8
CTS
NC
NC
9
RI
NC
NC