Winmate W07IB3S-PCO1AC-POE User manual

7"S-Series HMI
W07IB3S-PCO1AC-POE (With LED Light Bar)
W07IB3S-PCO1-POE (Without LED Light Bar)
Slim-line
User Manual
Version 1.5
Document Part Number: 9171111I102C

USER MANUAL CONTENTS
- 2 -
CONTENTS
PREFACE........................................................................................................... - 1 -
ABOUT THIS USER MANUAL............................................................................ - 11 -
CHAPTER 1: INTRODUCTION ........................................................................... - 13 -
1.1 Product Features...................................................................................- 13 -
1.2 Package Contents..................................................................................- 14 -
1.3 Product Overview .................................................................................- 16 -
CHAPTER 2: GETTING STARTED ....................................................................... - 18 -
2.1 Powering On..........................................................................................- 18 -
2.1.1 AC Adapter Components............................................................- 18 -
2.1.2 Power Considerations ................................................................- 19 -
2.1.3 Connecting the Power................................................................- 20 -
2.2 Connector Pinouts ................................................................................- 21 -
2.2.1 Power Input Connector ..............................................................- 21 -
2.2.2 Serial Port Connector .................................................................- 21 -
2.2.3 RJ45 Connector...........................................................................- 21 -
2.2.4 USB A Type Connector................................................................- 22 -
2.3 Configuring Serial Port Settings ............................................................- 23 -
2.4 Turning On and Off ...............................................................................- 24 -
CHAPTER 3: OPERATING THE HMI DEVICE ....................................................... - 26 -
3.1 Operating System..................................................................................- 26 -
3.2 System Settings.....................................................................................- 27 -
3.2.1 Hot Tab Menu.............................................................................- 27 -
3.2.2 Utilities........................................................................................- 27 -
3.2.3 Brightness...................................................................................- 28 -
3.2.4 Volume .......................................................................................- 28 -
3.2.5 LED Light Bar...............................................................................- 28 -
3.2.6 Performance...............................................................................- 29 -
3.2.7 Touch Lock..................................................................................- 29 -
3.2.8 Using Front Camera....................................................................- 30 -
3.3 Using HF RFID Reader ...........................................................................- 33 -
3.3.1 HF RFID Reader Location............................................................- 33 -

USER MANUAL CONTENTS
- 3 -
3.3.2 Trigger Setting ............................................................................- 34 -
3.3.3 Settings.......................................................................................- 34 -
3.3.4 RFID Output Settings ..................................................................- 36 -
3.3.5 Writing Mode .............................................................................- 36 -
3.4 How to Enable Watchdog .....................................................................- 37 -
CHAPTER 4: DRIVER INSTALATION...................................................................- 39 -
4.1 Installing Chipset Driver........................................................................- 39 -
4.2 Installing Graphics Driver......................................................................- 41 -
4.3 Installing Intel Sideband Fabric Device (Intel MBI) Driver (Windows 8)- 42 -
4.4 Installing Intel Trusted Engine Interface (Intel TXE) Driver ..................- 43 -
4.5 Installing Intel Network Connections....................................................- 44 -
4.6 Installing Audio Driver...........................................................................- 45 -
4.7 Installing USB 3.0 Driver (Windows 7) ..................................................- 46 -
CHAPTER 5: BIOS SETUP..................................................................................- 48 -
5.1 When and How to Use BIOS Setup .......................................................- 48 -
5.2 BIOS Functions ......................................................................................- 49 -
5.2.1 Main Menu .................................................................................- 50 -
5.2.2 Advanced Menu .........................................................................- 51 -
5.2.3 Chipset Menu .............................................................................- 70 -
5.2.4 Security Menu ............................................................................- 71 -
5.2.5 Boot Configuration .....................................................................- 72 -
5.2.6 Save & Exit..................................................................................- 74 -
5.3 Using Recovery Wizard to Restore Computer ......................................- 76 -
CHAPTER 6: MOUNTING..................................................................................- 78 -
6.1 Cable Mounting Considerations ...........................................................- 78 -
6.2 Safety Precautions ................................................................................- 79 -
6.3 Mounting Guide....................................................................................- 80 -
6.3.1 Panel Mounting ..........................................................................- 80 -
6.3.2 VESA Mounting...........................................................................- 81 -
6.3.3 Glass Wall Mounting ..................................................................- 85 -
CHAPTER 7: TECHNICAL SUPPORT ...................................................................- 87 -
7.1 Software Developer Support ................................................................- 87 -

USER MANUAL CONTENTS
- 4 -
7.1.1 Winmate Download Center........................................................- 87 -
7.1.2 Winmate File Share ....................................................................- 87 -
7.2 Problem Report Form ...........................................................................- 88 -
APPENDIX A: PRODUCT SPECIFICATIONS......................................................... - 90 -
APPENDIX B: HF RFID READER SPECIFICATIONS............................................... - 93 -

USER MANUAL PREFACE
PREFACE
Copyright Notice
No part of this document may be reproduced, copied, translated, or transmitted in
any form or by any means, electronic or mechanical, for any purpose, without the
prior written permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their
respective owners.
Disclaimer
Winmate Inc. reserve the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to
improve design and/or performance. We assume no responsibility or liability for the
use of the described product(s) conveys no license or title under any patent,
copyright, or masks work rights to these products, and make no representations or
warranties that these products are free from patent, copyright, or mask work right
infringement, unless otherwise specified. Applications that are described in this
manual are for illustration purposes only. We make no representation or guarantee
that such application will be suitable for the specified use without further testing or
modification.
Warranty
Winmate Inc. warranty guarantees that each of its products will be free from
material and workmanship defects for a period of one year from the invoice date. If
the customer discovers a defect, we will, at his/her option, repair or replace the
defective product at no charge to the customer, provide it is returned during the
warranty period of one year, with transportation charges prepaid. The returned
product must be properly packaged in its original packaging to obtain warranty
service. If the serial number and the product shipping data differ by over 30 days,
the in-warranty service will be made according to the shipping date. In the serial
numbers the third and fourth two digits give the year of manufacture, and the fifth
digit means the month (e. g., with A for October, B for November and C for
December).
For example, the serial number 1W16Axxxxxxxx means October of year 2016.

USER MANUAL PREFACE
- 2 -
Customer Service
We provide a service guide for any problem by the following steps: First, visit the
website of our distributor to find the update information about the product.
Second, contact with your distributor, sales representative, or our customer
service center for technical support if you need additional assistance.
You may need the following information ready before you call:
Product serial number
Software (OS, version, application software, etc.)
Description of complete problem
The exact wording of any error messages
In addition, free technical support is available from our engineers every business
day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.

USER MANUAL PREFACE
- 3 -
Advisory Conventions
Four types of advisories are used throughout the user manual to provide helpful
information or to alert you to the potential for hardware damage or personal injury.
These are Notes, Important, Cautions, and Warnings. The following is an example of
each type of advisory.
NOTE:
A note is used to emphasize helpful information
IMPORTANT:
An important note indicates information that is important for you to
know.
CAUTION/ ATTENTION
A Caution alert indicates potential damage to hardware and explains how
to avoid the potential problem.
Une alerte d’attention indique un dommage possible à l’équipement et
explique comment éviter le problème potentiel.
WARNING!/ AVERTISSEMENT!
An Electrical Shock Warning indicates the potential harm from electrical
hazards and how to avoid the potential problem.
Un Avertissement de Choc Électrique indique le potentiel de chocs sur
des emplacements électriques et comment éviter ces problèmes.
ALTERNATING CURRENT / MISE À LE TERRE!
The Protective Conductor Terminal (Earth Ground) symbol indicates the
potential risk of serious electrical shock due to improper grounding.
Le symbole de Mise à Terre indique le risqué potential de choc
électrique grave à la terre incorrecte.

USER MANUAL PREFACE
- 4 -
Safety Information
WARNING! / AVERTISSEMENT!
Always completely disconnect the power cord from your chassis
whenever you work with the hardware. Do not make connections
while the power is on. Sensitive electronic components can be
damaged by sudden power surges. Only experienced electronics
personnel should open the PC chassis.
Toujours débrancher le cordon d’alimentation du chassis lorsque
vous travaillez sur celui-ci. Ne pas brancher de connections lorsque
l’alimentation est présente. Des composantes électroniques
sensibles peuvent être endommagées par des sauts d’alimentation.
Seulement du personnel expérimenté devrait ouvrir ces chassis.
CAUTION/ATTENTION
Always ground yourself to remove any static charge before touching
the CPU card. Modern electronic devices are very sensitive to static
electric charges. As a safety precaution, use a grounding wrist strap
at all times. Place all electronic components in a static-dissipative
surface or static-shielded bag when they are not in the chassis.
Toujours verifier votre mise à la terre afin d’éliminer toute charge
statique avant de toucher la carte CPU. Les équipements
électroniques moderns sont très sensibles aux décharges
d’électricité statique. Toujours utiliser un bracelet de mise à la terre
comme précaution. Placer toutes les composantes électroniques sur
une surface conçue pour dissiper les charge, ou dans un sac anti-
statique lorsqu’elles ne sont pas dans le chassis.

USER MANUAL PREFACE
- 5 -
Safety Precautions
For your safety carefully read all the safety instructions before using the
device. Keep this user manual for future reference.
Always disconnect this equipment from any AC outlet before cleaning.
Do not use liquid or spray detergents for cleaning. Use a damp cloth.
For pluggable equipment, the power outlet must be installed near the
equipment and must be easily accessible.
Keep this equipment away from humidity.
Put this equipment on a reliable surface during installation. Dropping it
or letting it fall could cause damage.
The openings on the enclosure are for air convection and to protect the
equipment from overheating.
CAUTION/ATTENTION
Do not cover the openings!
Ne pas couvrir les ouvertures!
Before connecting the equipment to the power outlet make sure the
voltage of the power source is correct.
Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient over-voltage.
Never pour any liquid into an opening. This could cause fire or electrical
shock.
Never open the equipment. For safety reasons, only qualified service
personnel should open the equipment.
All cautions and warnings on the equipment should be noted.

USER MANUAL PREFACE
- 6 -
*Let service personnel to check the equipment in case any of the following
problems appear:
oThe power cord or plug is damaged.
oLiquid has penetrated into the equipment.
oThe equipment has been exposed to moisture.
oThe equipment does not work well or you cannot get it to work
according to the user manual.
oThe equipment has been dropped and damaged.
oThe equipment has obvious signs of breakage.
Do not leave this equipment in an uncontrolled environment where the
storage temperature is below -20°C (-4°F) or above 60°C (140°F). It may
damage the equipment.
CAUTION/ATTENTION
Use the recommended mounting apparatus to avoid risk of injury.
Utiliser l’appareil de fixation recommandé pour éliminer le risque
de blessure.
WARNING! / AVERTISSEMENT!
Only use the connection cords that come with the product. When
in doubt, please contact the manufacturer.
Utiliser seulement les cordons d’alimentation fournis avec le
produit. Si vous doutez de leur provenance, contactez le
manufacturier.
WARNING!/ AVERTISSEMENT!
Always ground yourself against electrostatic damage to the
device.
Toujours vérifier votre mise à la terre afin que l’équipement ne se
décharge pas sur vous.

USER MANUAL PREFACE
- 7 -
Cover workstations with approved anti-static material. Use a wrist
strap connected to a work surface and properly grounded tools and
equipment.
Use anti-static mats, heel straps, or air ionizer for added protection.
Handle electrostatic-sensitive components, PCB’s and assemblies by
the case or the edge of the board.
Avoid contact with pins, leads, or circuitry.
Turn off power and input signals before inserting and removing
connectors or test equipment.
Keep the work area free of non-conductive materials, such as ordinary
plastic assembly aids and Styrofoam.
Use filed service tools, such as cutters, screwdrivers, and vacuum
cleaners that are conductive.
Always put drivers and PCB’s component side on anti-static foam.

USER MANUAL PREFACE
- 8 -
Important Information
Countries/ Area
Symbol
This equipment complies with essential
requirements of:
European Union
Electromagnetic Compatibility
Directive(2014/30/EU)
Low Voltage Directive (2014/35/EU)
Restrictions of the use of certain hazardous
substances (RoHS) Directive (2011/65/EU)
USA
FCC Part 15 Subpart B Regulations Class B

USER MANUAL PREFACE
- 9 -
Federal Communications Commission Radio Frequency Interface Statement
This device complies with part 15 FCC rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class "B"
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
him own expense.
.

USER MANUAL PREFACE
- 10 -
European Union
This equipment is in conformity with the requirement of the following EU
legislations and harmonized standards. Product also complies with the Council
directions.
Electromagnetic Compatibility Directive (2014/30/EU)
EN55024: 2010/ A1: 2015
oIEC61000-4-2: 2009
oIEC61000-4-3: 2006+A1: 2007+A2: 2010
oIEC61000-4-4: 2012
oIEC61000-4-5: 2014
oIEC61000-4-6: 2014
oIEC61000-4-8: 2010
oIEC61000-4-11: 2004
EN55032: 2012/AC:2013
EN61000-3-2:2014
EN61000-3-3:2013
Low Voltage Directive (2014/35/EU)
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/ A2:2013

USER MANUAL ABOUT THIS USER MANUAL
- 11 -
ABOUT THIS USER MANUAL
This User Manual provides information about using the Winmate® 7” S-Series HMI with I
Intel ® Celeron ® Bay Trail-M N2930 1.83 GHz processor. The documentation set for the
7” S -Series HMI provides information for specific user needs, and includes:
7” S-Series HMI Quick Start Guide - describes how to get the HMI device up and
running.
7” S-Series HMI User Manual –contains detailed description on how to use the
HMI device, its components and features.
NOTE:
Some pictures in this guide are samples and can differ from actual
product
Revision History
Version
Date
Note
1.0
17-Mar-2016
Initial release
1.1
15-Jun-2016
New Hot Tab and Light Bar user interface.
1.2
25-Jul-2016
Add section Ch.3, “How to Enable Watchdog”
1.3
11-Nov-2016
Add HF RFID Reader
1.4
17-Mar-2017
Motherboard design change
1.5
16-Nov-2017
Change panel to O1

USER MANUAL CHAPTER 1 INTRODUCTION
- 12 -
INTRODUCTION
This chapter gives you product overview,
describes features and hardware specification.
You will find all accessories that come with the
HMI device in the packing list. Mechanical
dimensions and drawings included in this chapter.

USER MANUAL CHAPTER 1 INTRODUCTION
- 13 -
CHAPTER 1: INTRODUCTION
Interactive and smart automation systems of intelligent buildings are in a fast growing
phase. Winmate® multi-touch S-Series HMI is suitable for home automation and room
management systems. Flat surface is easy-to-clean and delivers aesthetically pleasing
look for any interior. The device provides real time update for booking status and
available schedule, or performs as a synchronous display in meetings. Optional 2-
megapixel front camera is especially useful in meetings and on-line conferences. Also
front camera allows using face recognition system resulting in increased security for
access control applications.
7” S-Series HMI runs on Intel® Celeron® N2930 processor and support Windows 10 IoT,
Windows Embedded 8.1 Industry Pro, Windows Embedded 8 Standard, and Windows
Embedded Standard 7 –WS7P. The HMI features P-Cap touch-screen with 1024 x 600
pixel resolution. These models sealed with front IP 65 dust and water proof, and full IP22.
The W07IB3S-PCM1AC model supports an exceptional feature - LED light bar. With the
help of red, green, blue and orange LED indicators you can see the status of the machine
or processes afar. It significantly reduces power consumption by keeping the display
turned off.
1.1 Product Features
Winmate® 7” S-Series HMI features:
1024 x 600 screen resolution with P-CAP multi-touch
Intel® Celeron® Bay Trail-M N2930 1.83 GHz
Fanless cooling system and Ultra-low power consumption
Front IP65 water and dust proof, rear IP22
Dual Gigabit Ethernet
LED Light Bar (for model W07IB3S-PCM1AC)
Optional 2MP front camera
Optional HF RFID Reader
Stylish design for room booking, access control and room information
applications

USER MANUAL CHAPTER 1 INTRODUCTION
- 14 -
1.2 Package Contents
Carefully remove the box and unpack your HMI device. Please check if all the items listed
below are inside your package. If any of these items are missing or damaged contact us
immediately.
Standard factory shipment list:
7” HMI Device
Quick Start Guide
(Hardcopy)
Driver CD & User Manual
Varies by product
specifications
9152070I1002
IB32: 9171111I101Y
AC Adapter
(12V/ 50W)
Power Cable
VESA Plate
75 x 75 mm
922D050W12VA
Varies by country
82W70J17Y700
VESA Mounting Screws
913511101145

USER MANUAL CHAPTER 1 INTRODUCTION
- 15 -
Package may include optional accessories based on your order:
VESA Desk Stand
PCVS-V1
VESA Desk Stand
LA-100
VESA Wall Mount Bracket
LA-106
99KK00A0000E
9B0000000128
9B0000000412
Glass Wall Mount Kit
Right: PCGM-V1L
Left: PCGM-V1L
Right: 99KN00A00013
Left:99KN00A00012

USER MANUAL CHAPTER 1 INTRODUCTION
- 16 -
1.3 Product Overview
No.
Description
No.
Description
①
RJ-45 (LAN)
⑥
1 Watt Speaker
②
USB 3.0, USB 2.0
⑦
2MP Front Camera (Optional)
③
RS-232
⑧
RGB LED Light Bar
(W07IB3S-PCM1AC only)
④
12V DC Terminal Block
⑨
HF RFID Reader (Optional)
⑤
RJ-45 (LAN/ PoE)
*RGB LED light bar only available for the model number W07IB3S-PCM1AC