Winners Only T2-VT100E-G User manual

OSS-16031-TDG
T2-VT100S--G,T2-SF100S--C
SOFA TABLE WITH 2 DRAWERS
Reminders :
Two people are needed for assembly.
Use only hardware supplied.
Do not over tighten bolts.
This item may require periodic tightening.
MADE IN MALAYSIA
Page 2 of 2
HARDWARE PART :
Wrench
Flat Washer
Lock Washer
1 pc
8 pcs 4 pcs
Hex Bolt
8 pcs 8 pcs
Pan Head Screw
ASSEMBLY :
STEP 1
Pull out the Drawer Box as shown and Turn the Table Top upside down on a protective surface such as carpet or other soft material.
Use Flat Washer, Lock Washer, Hex Bolt and Wrench, to attach three legs randomly to the table top, do not fully tighten yet. Insert
the fixed shelf into the legs as shown in the diagram.
STEP 2
Insert the Fixed Shelf into three legs, insert the last leg to the corner of apron frame and bottom Fixed Shelf.Then tighten with
Flat Washer,Lock Washer and Hex Bolt using the Wrench provided.And fix the Fixed shelf by insert and tighten the
Pan Head Screw using the screw-driver (Not provided).
STEP 3
Check its balance and tighten all bolts to complete the assembly.
Lock Washer
Hex Bolt
Wrench
Flat Washer
CARE INSTRUCTION
~ Be sure to use the same type of polish consistenly.
Your furniture will appear cloudy or streaky if oil
based or wax based polishes are interchanged.
~ Spray your furniture surface evenly. Wipe in a
circular motion with a soft clean cloth.
IMPORTANT NOTE :
~ Please keep all hardware out of the reach of
children.
OLS-16032-SNN
Reminders :
Two people are needed for assembly.
Use only hardware supplied.
Do not over tighten bolts.
This item may require periodic tightening.
MADE IN MALAYSIA
Page 2 of 2
HARDWARE PART :
Flat Washer Allen Key
Lock Washer
1 pce
JCBC Bolt JCBC Bolt
(Short)
(Long)
8 pcs 4 pcs 12 pcs 12 pcs
ASSEMBLY :
STEP 1
Turn the Table Top upside down on a protective surface such as carpet or other soft material.Place the three legs to the corner of the
apron then insert the Flat Washer, Lock Washer and JCBC Bolt(Long) into pre-drilled holes on the corner block and tighten it by using
the Allen key provided. Insert the Fixed Shelf into the assembly legs as shown in the diagram, then install the fourth leg by use
Flat Washer, Lock Washer and JCBC Bolt(Long)into pre-drilled holes on the corner block and tighten it by using the Allen key
provided. Continue by using the Flat Washer, Lock Washer and JCBC Bolt(Short) into pre-drilled holes on the corner block of
Fixed Shelf and by using the Allen key provided.
STEP 2
Check its balance and tighten all bolts to complete the assembly.
CARE INSTRUCTION
~ Be sure to use the same type of polish consistenly.
Your furniture will appear cloudy or streaky if oil
based or wax based polishes are interchanged.
~ Spray your furniture surface evenly. Wipe in a
circular motion with a soft clean cloth.
IMPORTANT NOTE :
~ Please keep all hardware out of the reach of
children.
T2-NP101E--0
LAMP TABLE
Allen Key
Allen Key
JCBC Bolt
(Short)
JCBC Bolt
(Long)
Lock Washer
Lock Washer
Flat Washer
Flat Washer
PARTS LIST
OES-16031-TDG MADE IN MALAYSIA
Page 1 of 2
T2-VT100E--G,T2-SF100E--C
END TABLE
PART NO FIGURE DESCRIPTION QTY
Legs
Table Top 1 pce
4 pcs
1 pce
T2-VT100E-01,
T2-SF100E-01
T2-VT100E-13,
T2-SF100E-13
T2-VT100E-13,
T2-SF100E-13
T2-VT100E-07,
T2-SF100E-07
T2-VT100E-07,
T2-SF100E-07
T2-VT100E-22,
T2-SF100E-22
T2-VT100E-22,
T2-SF100E-22
Hardware Bag 1 pce
Fixed Shelf
IMPORTANT NOTE : Please keep all hardware parts out of the reach of children.

OSS-16031-TDG
T2-VT100S--G,T2-SF100S--C
SOFA TABLE WITH 2 DRAWERS
Reminders :
Two people are needed for assembly.
Use only hardware supplied.
Do not over tighten bolts.
This item may require periodic tightening.
MADE IN MALAYSIA
Page 2 of 2
HARDWARE PART :
Wrench
Flat Washer
Lock Washer
1 pc
8 pcs 4 pcs
Hex Bolt
8 pcs 8 pcs
Pan Head Screw
ASSEMBLY :
STEP 1
Pull out the Drawer Box as shown and Turn the Table Top upside down on a protective surface such as carpet or other soft material.
Use Flat Washer, Lock Washer, Hex Bolt and Wrench, to attach three legs randomly to the table top, do not fully tighten yet. Insert
the fixed shelf into the legs as shown in the diagram.
STEP 2
Insert the Fixed Shelf into three legs, insert the last leg to the corner of apron frame and bottom Fixed Shelf.Then tighten with
Flat Washer,Lock Washer and Hex Bolt using the Wrench provided.And fix the Fixed shelf by insert and tighten the
Pan Head Screw using the screw-driver (Not provided).
STEP 3
Check its balance and tighten all bolts to complete the assembly.
Lock Washer
Hex Bolt
Wrench
Flat Washer
CARE INSTRUCTION
~ Be sure to use the same type of polish consistenly.
Your furniture will appear cloudy or streaky if oil
based or wax based polishes are interchanged.
~ Spray your furniture surface evenly. Wipe in a
circular motion with a soft clean cloth.
IMPORTANT NOTE :
~ Please keep all hardware out of the reach of
children.
OLS-16032-SNN
Reminders :
Two people are needed for assembly.
Use only hardware supplied.
Do not over tighten bolts.
This item may require periodic tightening.
MADE IN MALAYSIA
Page 2 of 2
HARDWARE PART :
Flat Washer Allen Key
Lock Washer
1 pce
JCBC Bolt JCBC Bolt
(Short)
(Long)
8 pcs 4 pcs 12 pcs 12 pcs
ASSEMBLY :
STEP 1
Turn the Table Top upside down on a protective surface such as carpet or other soft material.Place the three legs to the corner of the
apron then insert the Flat Washer, Lock Washer and JCBC Bolt(Long) into pre-drilled holes on the corner block and tighten it by using
the Allen key provided. Insert the Fixed Shelf into the assembly legs as shown in the diagram, then install the fourth leg by use
Flat Washer, Lock Washer and JCBC Bolt(Long)into pre-drilled holes on the corner block and tighten it by using the Allen key
provided. Continue by using the Flat Washer, Lock Washer and JCBC Bolt(Short) into pre-drilled holes on the corner block of
Fixed Shelf and by using the Allen key provided.
STEP 2
Check its balance and tighten all bolts to complete the assembly.
CARE INSTRUCTION
~ Be sure to use the same type of polish consistenly.
Your furniture will appear cloudy or streaky if oil
based or wax based polishes are interchanged.
~ Spray your furniture surface evenly. Wipe in a
circular motion with a soft clean cloth.
IMPORTANT NOTE :
~ Please keep all hardware out of the reach of
children.
T2-NP101E--0
LAMP TABLE
Allen Key
Allen Key
JCBC Bolt
(Short)
JCBC Bolt
(Long)
Lock Washer
Lock Washer
Flat Washer
Flat Washer
OES-16031-TDG
T2-VT100E--G,T2-SF100E--C
END TABLE
Reminders :
Two people are needed for assembly.
Use only hardware supplied.
Do not over tighten bolts.
This item may require periodic tightening.
MADE IN MALAYSIA
Page 2 of 2
HARDWARE PART :
Wrench
Flat Washer
Lock Washer
1 pc
8 pcs 4 pcs
Hex Bolt
8 pcs 8 pcs
Pan Head Screw
ASSEMBLY :
STEP 3
Check its balance and tighten all bolts to complete the assembly.
Lock Washer
Hex Bolt
Wrench
Flat Washer
CARE INSTRUCTION
~ Be sure to use the same type of polish consistenly.
Your furniture will appear cloudy or streaky if oil
based or wax based polishes are interchanged.
~ Spray your furniture surface evenly. Wipe in a
circular motion with a soft clean cloth.
IMPORTANT NOTE :
~ Please keep all hardware out of the reach of
children.
STEP 1
Pull out the Drawer Box as shown and Turn the Table Top upside down on a protective surface such as carpet or other soft material.
Use Flat Washer, Lock Washer, Hex Bolt and Wrench, to attach three legs randomly to the table top, do not fully tighten yet. Insert
the fixed shelf into the legs as shown in the diagram.
STEP 2
Insert the Fixed Shelf into three legs, insert the last leg to the corner of apron frame and bottom Fixed Shelf.Then tighten with
Flat Washer,Lock Washer and Hex Bolt using the Wrench provided.And fix the Fixed shelf by insert and tighten the
Pan Head Screw using the screw-driver (Not provided).