Wiseup DVR-0031-4 User manual

DVR-0031-4
User Guide
I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“BVCAM” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “CM*****”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]: If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “BVCAM” APP.
4.1.4. Add the camera to the “BVCAM” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “Online” on the “Live video” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “Offline”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “online”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “BVCAM” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “WIFI Config” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “OK” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “BVCAM” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “BVCAM” APP again. If the camera shows “Online” on the “Live video” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]: If the camera shows “Device Offline”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “BVCAM” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “Alarm Config” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “Warning Tone”, “Push Notification” and
“On-screen Display” is also available.
Step 3: Tap “OK” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “Live video”
page and tap “Alarm” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “Live video” page then choose "Advance Config" or
“Device Settings”.
Step 2: Go to “SDCard Record Config” page and choose “On alarm”, then set resolution and
file length. Enabling “Record sound” and “Loop recording” is also available.
Step 3: Tap “OK” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “Live video” page, tap “Record” at the bottom of the screen and then tap
"Remote SD Card" or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “Format”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “BVCAM” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “BVCAM”.
6.3. Go back to the “Live video” page, tap “Record” at the bottom of the screen and then
tap "Local" or to check out the video files.
[Note]: Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “BVCAM”APP.
7.2. Tap the setting icon on the “Live video” page then select "Advance Config" or “Device
Settings”.
7.3. Go to “SD Card Record Config” page, then set a desired recording mode and file length.
Enabling “Record sound” and “Loop recording” is also available.
7.4. Tap “OK” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “BVCAM” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “Live video” page then choose “Modify Device” or “Device
Settings” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “OK” or “√” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “Live video” page, and tap “Change” in the popup window.
Step 2: Enter the new password and confirm it, then tap “OK” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “Live video” page, tap "Advance Config" or “Device
Settings”, then go to "Change P2P access password" or “Change password” page.
Step 2: Enter the default password “8888” at first, then enter a new password and confirm it,
tap “OK” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “BVCAM” APP on your
other Android phones or tablet PCs, tap “+” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “OK” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.

DVR-0031-4
Benutzerhandbuch
I. Produktübersicht
1. Kameraobjektiv
2. Reset-Taste
3. Netzschalter
4. Leistungsaufnahme
5. Rote Kontrollleuchte
6. Blaues Indikatorlicht
II. Was ist in der Box
-1 × WIFI Rauchmelder Kamera
-1 × AC110-240V zum DC5V Netzteil
III. Bevor du anfängst
3.1. Bitte stellen Sie sicher, dass Ihre Kamera vor dem Gebrauch vollständig aufgeladen ist.
3.2 Wenn Sie möchten, dass die Kamera 7/24 Stunden arbeitet, schließen Sie sie bitte an
eine Steckdose mit dem mitgelieferten DC5V Netzteil an.
3.3. Für Android-, iPhone- und iPad-Benutzer scannen Sie bitte den QR-Code, um die
"BVCAM" APP herunterzuladen.
IV. Netzwerkeinrichtung
4.1. LAN (P2P) Modus Setup
4.1.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter ca. 2 Sekunden lang drücken.
Es wird 1 Minute dauern, bis das WIFI-Signal erscheint. Wenn die blaue Kontrollleuchte zu
blinken beginnt und die rote Kontrollleuchte solide bleibt, bedeutet das, dass das WIFI-Signal
der Kamera bereit ist.
4.1.2. Gehen Sie auf die WIFI- oder WLAN-Einstellungsseite auf Ihrem Telefon oder Mobilgerät,
verbinden Sie das WIFI-Signal der Kamera mit dem Namen "CM *****". Warten Sie, bis das WIFI
angeschlossen ist und Ihre Telefonstatusleiste erscheint als WIFI-Symbol wie folgt:
[Hinweis]: Wenn das WIFI-Signal der Kamera nach langer Zeit nicht gefunden werden kann, bitte
die Kamera aufladen oder zurücksetzen (siehe VIII).
4.1.3. Führen Sie die "BVCAM" APP.
4.1.4. Füge die Kamera zum "BVCAM" APP wie folgt hinzu:
Für Android: Tippen Sie auf +> Tippen Sie auf Neues Online-Gerät hinzufügen> Suche
nach der Kamera> Tippen Sie auf das Kamerasymbol> Tippen Sie auf OK oder √.
Für IOS: Tippen Sie auf +> Tippen Sie auf Neue Online-Kamera hinzufügen> Suche nach
der Kamera> Tippen Sie auf das Kamerasymbol> Tippen Sie auf OK.
4.1.5. Wenn die Kamera auf der Seite "Live-Video" auf "Online" zeigt, bedeutet das, dass
das P2P (LAN) Setup der Kamera erfolgreich ist. Sie können Videos im P2P (LAN) Modus
überprüfen oder aufnehmen.
[Hinweis]:
1) Wenn die Kamera "Offline" anzeigt, ist das normal. Verlasse die APP und öffne sie wieder.
Warten Sie eine Minute und die Kamera wird "online" sein.
2). In diesem P2P (LAN) -Modus können Sie nur Video lokal, innerhalb von 15 Metern (49 Fuß)
offenen Bereich.
4.1.6. Auf dem Live-Video-Bildschirm können Sie sanft Ihren Zeigefinger und Daumen auf
den Bildschirm und dann nach innen und nach außen Richtungen auf einem bestimmten
Bereich zu vergrößern und verkleinern.
4.2. Remote View Setup (WAN-Modus)
>> Bevor Sie das Setup der Fernbedienung vornehmen, stellen Sie bitte sicher, dass die
Kamera erfolgreich in die APP aufgenommen wurde und es im P2P (LAN) Modus online
ist.
4.2.1. Starten Sie die "BVCAM" APP.
4.2.2. Richten Sie die Remote View-Funktion wie folgt ein:
Schritt 1: Tippen Sie auf die Einstellung "Live Video" und wählen Sie dann "Advance Config"
oder "Device Settings".
Schritt 2: Gehe zur Seite "WIFI Config" und wähle einen gewünschten WIFI-Hotspot aus, um
die Kamera einzuschreiben.
Schritt 3: Tippen Sie auf "OK", um das Setup der Fernbedienung abzuschließen, und die
Kamera wird automatisch neu gestartet.
Wie kann man überprüfen, ob die Remote View Funktion funktioniert?
1. Beenden Sie die "BVCAM" APP.
2. Zurück zur WIFI- oder WLAN-Einstellungsseite auf Ihrem Telefon oder Mobilgerät beenden
Sie Ihr Telefon oder Mobilgerät aus dem aktuellen WIFI-Netzwerk, registrieren Sie Ihr Telefon
oder Mobilgerät in einem anderen WIFI-Hotspot oder Sie können die WIFI- oder WLAN-Funktion
deaktivieren , Aktivieren Sie stattdessen Ihre mobilen Netzwerkdaten.
3. Starten Sie den "BVCAM" APP erneut. Wenn die Kamera auf der Seite "Live-Video" auf
"Online" zeigt, bedeutet dies, dass das Remote-View-Setup erfolgreich ist und die
Kamera in den WAN-Modus gelangt ist. Beide blauen und roten Kontrollleuchten leuchten.
Sie können vorwärts gehen, um Live-Video zu sehen oder Video zu erfassen.
[Hinweis]: Wenn die Kamera "Device Offline" anzeigt, bedeutet dies, dass das Remote View Setup
fehlgeschlagen ist und Sie die Kamera zurücksetzen müssen (siehe VIII) und wieder einrichten.
V. Bewegungserkennung Aufnahme Setup
>> Bitte stellen Sie sicher, dass die Kamera der APP im LAN- oder WAN-Modus hinzugefügt
wird und es ist online, bevor Sie beginnen.
5.1. Starten Sie die "BVCAM" APP.
5.2. Stellen Sie die Bewegungserkennung wie folgt auf:
Schritt 1: Tippen Sie auf das Einstellungssymbol auf der Seite "Live Video" und wählen Sie
dann "Advance Config" oder "Device Settings".
Schritt 2: Gehen Sie auf "Alarm Config" -Seite, dort können Sie eine gewünschte
Alarmempfindlichkeit, Alarmzeitplan und Alarmintervall einstellen. Es ist auch die Option
"Warnton", "Push Notification" und "On-Screen Display" verfügbar.
Schritt 3: Tippen Sie auf "OK", um die Einstellung abzuschließen.
Schritt 4: Wenn die Bewegung erkannt wird, schaltet die Kamera eine Warnmeldung an Ihr
Telefon und wird einen Screenshot der Live-Videoseite automatisch machen. Sie können wieder
auf die Seite "Live Video" und tippen Sie auf "Alarm" am unteren Rand des Bildschirms, um die
Fotos auszuprobieren.
5.3. Setzen Sie die SD-Karten-Videoaufzeichnung auf der Grundlage der Bewegungserkennung
wie folgt ein:
Schritt 1: Tippen Sie auf die Einstellung "Live Video" und wählen Sie dann "Advance Config"
oder "Device Settings".
Schritt 2: Gehen Sie auf "SDCard Record Config" -Seite und wählen Sie "On Alarm", dann
setzen Auflösung und Dateilänge. Die Aktivierung von "Record sound" und "Loop Recording"
ist ebenfalls möglich.
Schritt 3: Tippen Sie auf "OK", um die Motion Detection Video Recording-Einstellung
abzuschließen.
Schritt 4: Wenn die Bewegung erkannt wird, schaltet die Kamera eine Alarmmeldung an Ihr
Telefon oder Mobilgerät und zeichnet ein Video automatisch in den internen Speicher der
Kamera auf. Sie können auf die Seite "Live Video" zurückkehren, tippen Sie auf "Record" am
unteren Rand des Bildschirms und tippen Sie dann auf "Remote SD Card" oder um die
Videodateien auszuprobieren.
[Hinweis]:
1) Video Auflösung: 1280 × 720P, 640x480, 320x240 Video Format: ASF
2). Wenn aus irgendeinem Grund die Videodateien nicht im internen Speicher gespeichert werden
können, können Sie den Speicher formatieren, indem Sie auf "Format" tippen.
VI. Aufnehmen von Video auf Smartphone oder Tablet PC
>> Bitte stellen Sie sicher, dass die Kamera der APP in LAN oder WAN hinzugefügt wird,
bevor Sie beginnen.
6.1. Starten Sie die "BVCAM" APP. Tippen Sie auf das Kamerasymbol, um in den
Live-Videobildschirm zu gelangen.
6.2. Tippen Sie auf die Aufnahmetaste und die Audio-Taste , um die Aufnahme
zu starten oder zu stoppen.
Für Android-Benutzer werden die Videodateien im Flash-Speicher des Mobilgeräts
gespeichert. Bei IOS-Benutzern werden die Videodateien nur im APP "BVCAM" gespeichert.
6.3. Gehen Sie zurück zur Seite "Live Video", tippen Sie auf "Record" am unteren Rand des
Bildschirms und tippen Sie dann auf "Local" oder um die Videodateien auszuprobieren.
[Anmerkung]: Videoauflösung: 1280 × 720P, 640x480, 320x240 Videoformat: ASF
VII. Aufnehmen von Video auf lokale Micro SD-Karte
>> Bitte stellen Sie sicher, dass die Kamera der APP im LAN- oder WAN-Modus hinzugefügt
wird, bevor Sie beginnen.
7.1. Starten Sie die "BVCAM" APP.
7.2 Tippen Sie auf die Einstellung "Live Video" und wählen Sie dann "Advance Config" oder
"Device Settings".
7.3 Gehen Sie auf "SD Card Record Config" -Seite, dann legen Sie einen gewünschten
Aufnahmemodus und Dateilänge. Die Aktivierung von "Record sound" und "Loop Recording"
ist ebenfalls möglich.
7.4 Tippen Sie auf "OK", um die SD-Kartenaufzeichnungseinstellung abzuschließen, und die
Kamera nimmt das Video auf den internen Speicher auf.
7.5. Die Videodateien werden im internen Speicher dieser Kamera gespeichert. Sie können
die Videodateien nach Kapitel 5.3 ausprobieren.
VIII. Zurücksetzen
Wenn aus irgendeinem Grund die Kamera nicht mehr funktioniert oder nicht richtig
funktioniert, können Sie die Kamera zurücksetzen, um sie wieder in den normalen Betrieb
zurückzusetzen.
Bedienung: Wenn die Kamera eingeschaltet ist, halten Sie die Reset-Taste für 3 Sekunden
gedrückt, bis die blaue und rote Anzeige leuchtet. Die Kamera startet automatisch mit den
Standardeinstellungen innerhalb von 1 Minute.
IX. Umbenennen von Kamera & Ändern des Passworts
>> Bitte bestätigen Sie, dass die Kamera der APP hinzugefügt wird, und es ist online im
P2P (LAN) Modus, bevor Sie starten.
9.1. Starten Sie die "BVCAM" APP.
9.2. Ändern Sie den Kameranamen wie folgt:
Schritt 1: Tippen Sie auf das Einstellungssymbol auf der Seite "Live-Video" und wählen Sie im
Popup-Fenster "Gerät ändern" oder "Geräteeinstellungen".
Schritt 2: Löschen Sie den Standardnamen und geben Sie Ihren gewünschten Namen wie
Haus, Büro, Schlafzimmer usw. ein.
Schritt 3: Tippen Sie auf "OK" oder "√", um die Änderung zu bestätigen.
9.3. Ändern Sie das Passwort wie folgt:
OPTION 1
Schritt 1: Tippen Sie auf das Kamerasymbol auf der Seite "Live Video" und tippen Sie im
Popup-Fenster auf "Ändern".
Schritt 2: Geben Sie das neue Passwort ein und bestätigen Sie es, dann tippen Sie auf
"OK", um die Änderung zu speichern.
OPTION 2
Schritt 1: Tippen Sie auf das Symbol "Live Video", tippen Sie auf "Advance Config" oder
"Device Settings" und dann auf "Change P2P access password" oder "Change password"
-Seite.
Schritt 2: Geben Sie zuerst das Standard-Passwort "8888" ein, geben Sie dann ein neues
Passwort ein und bestätigen Sie es, tippen Sie auf "OK", um die Änderung zu speichern.
Häufig gestellte Fragen
Q1: Warum kann ich das WIFI-Signal der Kamera nicht auf meinem Smartphone oder
Tablet PC finden?
A1: Es gibt 4 Lösungen für dieses Problem:
1. Stecken Sie die Kamera mit dem mitgelieferten Netzteil in eine Steckdose. Warten Sie
1 Minute, bis das WIFI-Signal SSID erscheint.
2. Setzen Sie die Kamera zurück (siehe VIII) und warten Sie dann, bis das WIFI-Signal
SSID angezeigt wird.
3. Halten Sie Ihr Telefon oder Mobilgerät in der WIFI-Hotspot-Reihe der Kamera und
erfrischen die WIFI-Signalseite. Es kann bis zu 1 Minute dauern, bis der Hotspot auf der
Telefon- oder Mobiltelefon-WIFI-Einstellungsseite erkennbar wird.
4. Schalten Sie die WIFI-Funktion Ihres Telefons oder des Mobilgeräts für eine Weile aus,
und schalten Sie es dann wieder ein.
Q2: Warum funktioniert das WAN-Modus-Setup?
A2: Bitte stellen Sie sicher, dass Ihr Netzwerk in einem guten Zustand ist. Plus, das
WIFI-Netzwerk die Kamera ist konfiguriert mit kann nicht das gleiche mit einem Sie Ihr
Telefon zu verbinden.
Q3: Was kann ich tun, wenn ich das Passwort vergessen habe?
A3: Bitte die Kamera zurücksetzen (Siehe VIII)
Q4: Die APP kann die UID der Kamera nach der Auswahl von "Search (LAN)" nicht
finden?
A4: Stellen Sie sicher, dass Ihr Telefon oder Mobilgerät immer noch mit dem WIFI-Signal
der Kamera verbunden ist. Vergewissern Sie sich, dass die Kamera mit der Steckdose
versorgt wird oder die Kamera vollständig aufgeladen ist.
Q5: Warum Live-Video-Bildschirm zeigt sich schwarz und ein Suchkreis dreht sich in
der Mitte, aber nichts zeigt jemals?
A5: a. Wenn Ihre Kamera mit einem langsamen WIFI-Netzwerk verbunden ist, warten Sie
10-30 Sekunden, bis das Live-Video erneut angezeigt wird.
B. Wählen Sie auf der Live-Videoseite eine niedrigere Auflösung aus.
Q6: Live Video ist nicht glatt und klar?
A6: Wählen Sie eine geeignete Auflösung entsprechend der Echtzeit-Netzwerkumgebung
aus.
Q7: Wie viele mobile Geräte können gleichzeitig mit der Kamera verbinden?
A7: keine Begrenzung.
Q8: Es gibt nur 1 Benutzer, aber die Kamera zeigt 2 oder mehr Benutzer?
A8: a. Wenn Sie sich sehr oft anmelden, ist der letzte Login-Datensatz noch in. Wenn Sie
es alle 2-5 Minuten überprüfen, zeigt die Kamera sicher die genaue Anzahl der Benutzer.
B. Für Ihre Sicherheit und Privatsphäre, bitte ändern Sie das Passwort der Kamera für die
fi nde Zeit verwenden.
Q9: Wie viele Kameras werden auf der mobilen Applikation unterstützt?
A9: keine Begrenzung.
Q10: Gibt es irgendeine PC-Client-Software, die ich auf meinem Computer verwenden
kann?
A10: Bitte klicken Sie auf den PC-Client-Software-Download-Link und laden Sie die Zip-Datei
auf Ihren PC herunter:
Http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: Die Kamera hält meine WIFI-Einstellungen nicht und zeigt weiter, dass die Kamera
offline ist?
A11: Stellen Sie sicher, dass die Kamera im Bereich des guten WIFI-Signals liegt. Oder
überprüfen Sie, ob der Netzadapter für längere Zeit richtig angeschlossen ist.
Q12: Wird die Kamera immer noch funktionieren, wenn die Stromversorgung erlischt?
A12: Wenn sich die Kamera im P2P-Modus befindet, kann die Kamera immer noch arbeiten
und Videos aufnehmen, solange die Kamera noch geladen ist. Wenn sich die Kamera im
WAN-Modus befindet, funktioniert es erst, wenn die Stromversorgung wiederhergestellt ist und
der Internetzugang verfügbar ist.
Q13: Wie füge ich die Kamera zu mehr Geräten hinzu?
A13: Stellen Sie sicher, dass sich die Kamera bereits im WAN-Modus befindet. Dann
starten Sie die "BVCAM" APP auf Ihrem anderen Android-Handys oder Tablet-PCs, tippen
Sie auf "+" -Symbol, geben Sie die Kamera UID (eine einzigartige Kombination von Zahlen
und Buchstaben für Ihre Kamera). Schließlich tippen Sie auf "OK", um die Kamera zur APP
hinzuzufügen.
Q14: Welche Media Player Software soll ich verwenden, um die Videodateien auf meinem
Computer wiederzugeben?
A14: Klicken Sie auf den Link: http://www.videolan.org/vlc/index.html, um den VLC-Player
herunterzuladen und zu installieren, um Videodateien auf Ihrem PC oder Mac-Computer
wiederzugeben.
Q15: Wie kann ich die Videodateien im internen Speicher der Kamera lesen?
A15: Du kannst zurück zur Seite "Live Video" gehen, am unteren Bildschirmrand auf "Record"
tippen und dann auf "Remote SD Card" tippen oder die Videodateien ansehen. Oder Sie
können die Videodateien auf Ihr Smartphone herunterladen.

I. Produktübersicht
1. Kameraobjektiv
2. Reset-Taste
3. Netzschalter
4. Leistungsaufnahme
5. Rote Kontrollleuchte
6. Blaues Indikatorlicht
II. Was ist in der Box
-1 × WIFI Rauchmelder Kamera
-1 × AC110-240V zum DC5V Netzteil
III. Bevor du anfängst
3.1. Bitte stellen Sie sicher, dass Ihre Kamera vor dem Gebrauch vollständig aufgeladen ist.
3.2 Wenn Sie möchten, dass die Kamera 7/24 Stunden arbeitet, schließen Sie sie bitte an
eine Steckdose mit dem mitgelieferten DC5V Netzteil an.
3.3. Für Android-, iPhone- und iPad-Benutzer scannen Sie bitte den QR-Code, um die
"BVCAM" APP herunterzuladen.
IV. Netzwerkeinrichtung
4.1. LAN (P2P) Modus Setup
4.1.1. Schalten Sie die Kamera ein, indem Sie den Netzschalter ca. 2 Sekunden lang drücken.
Es wird 1 Minute dauern, bis das WIFI-Signal erscheint. Wenn die blaue Kontrollleuchte zu
blinken beginnt und die rote Kontrollleuchte solide bleibt, bedeutet das, dass das WIFI-Signal
der Kamera bereit ist.
4.1.2. Gehen Sie auf die WIFI- oder WLAN-Einstellungsseite auf Ihrem Telefon oder Mobilgerät,
verbinden Sie das WIFI-Signal der Kamera mit dem Namen "CM *****". Warten Sie, bis das WIFI
angeschlossen ist und Ihre Telefonstatusleiste erscheint als WIFI-Symbol wie folgt:
[Hinweis]: Wenn das WIFI-Signal der Kamera nach langer Zeit nicht gefunden werden kann, bitte
die Kamera aufladen oder zurücksetzen (siehe VIII).
4.1.3. Führen Sie die "BVCAM" APP.
4.1.4. Füge die Kamera zum "BVCAM" APP wie folgt hinzu:
Für Android: Tippen Sie auf +> Tippen Sie auf Neues Online-Gerät hinzufügen> Suche
nach der Kamera> Tippen Sie auf das Kamerasymbol> Tippen Sie auf OK oder √.
Für IOS: Tippen Sie auf +> Tippen Sie auf Neue Online-Kamera hinzufügen> Suche nach
der Kamera> Tippen Sie auf das Kamerasymbol> Tippen Sie auf OK.
4.1.5. Wenn die Kamera auf der Seite "Live-Video" auf "Online" zeigt, bedeutet das, dass
das P2P (LAN) Setup der Kamera erfolgreich ist. Sie können Videos im P2P (LAN) Modus
überprüfen oder aufnehmen.
[Hinweis]:
1) Wenn die Kamera "Offline" anzeigt, ist das normal. Verlasse die APP und öffne sie wieder.
Warten Sie eine Minute und die Kamera wird "online" sein.
2). In diesem P2P (LAN) -Modus können Sie nur Video lokal, innerhalb von 15 Metern (49 Fuß)
offenen Bereich.
4.1.6. Auf dem Live-Video-Bildschirm können Sie sanft Ihren Zeigefinger und Daumen auf
den Bildschirm und dann nach innen und nach außen Richtungen auf einem bestimmten
Bereich zu vergrößern und verkleinern.
4.2. Remote View Setup (WAN-Modus)
>> Bevor Sie das Setup der Fernbedienung vornehmen, stellen Sie bitte sicher, dass die
Kamera erfolgreich in die APP aufgenommen wurde und es im P2P (LAN) Modus online
ist.
4.2.1. Starten Sie die "BVCAM" APP.
4.2.2. Richten Sie die Remote View-Funktion wie folgt ein:
Schritt 1: Tippen Sie auf die Einstellung "Live Video" und wählen Sie dann "Advance Config"
oder "Device Settings".
Schritt 2: Gehe zur Seite "WIFI Config" und wähle einen gewünschten WIFI-Hotspot aus, um
die Kamera einzuschreiben.
Schritt 3: Tippen Sie auf "OK", um das Setup der Fernbedienung abzuschließen, und die
Kamera wird automatisch neu gestartet.
Wie kann man überprüfen, ob die Remote View Funktion funktioniert?
1. Beenden Sie die "BVCAM" APP.
2. Zurück zur WIFI- oder WLAN-Einstellungsseite auf Ihrem Telefon oder Mobilgerät beenden
Sie Ihr Telefon oder Mobilgerät aus dem aktuellen WIFI-Netzwerk, registrieren Sie Ihr Telefon
oder Mobilgerät in einem anderen WIFI-Hotspot oder Sie können die WIFI- oder WLAN-Funktion
deaktivieren , Aktivieren Sie stattdessen Ihre mobilen Netzwerkdaten.
3. Starten Sie den "BVCAM" APP erneut. Wenn die Kamera auf der Seite "Live-Video" auf
"Online" zeigt, bedeutet dies, dass das Remote-View-Setup erfolgreich ist und die
Kamera in den WAN-Modus gelangt ist. Beide blauen und roten Kontrollleuchten leuchten.
Sie können vorwärts gehen, um Live-Video zu sehen oder Video zu erfassen.
[Hinweis]: Wenn die Kamera "Device Offline" anzeigt, bedeutet dies, dass das Remote View Setup
fehlgeschlagen ist und Sie die Kamera zurücksetzen müssen (siehe VIII) und wieder einrichten.
V. Bewegungserkennung Aufnahme Setup
>> Bitte stellen Sie sicher, dass die Kamera der APP im LAN- oder WAN-Modus hinzugefügt
wird und es ist online, bevor Sie beginnen.
5.1. Starten Sie die "BVCAM" APP.
5.2. Stellen Sie die Bewegungserkennung wie folgt auf:
Schritt 1: Tippen Sie auf das Einstellungssymbol auf der Seite "Live Video" und wählen Sie
dann "Advance Config" oder "Device Settings".
Schritt 2: Gehen Sie auf "Alarm Config" -Seite, dort können Sie eine gewünschte
Alarmempfindlichkeit, Alarmzeitplan und Alarmintervall einstellen. Es ist auch die Option
"Warnton", "Push Notification" und "On-Screen Display" verfügbar.
Schritt 3: Tippen Sie auf "OK", um die Einstellung abzuschließen.
Schritt 4: Wenn die Bewegung erkannt wird, schaltet die Kamera eine Warnmeldung an Ihr
Telefon und wird einen Screenshot der Live-Videoseite automatisch machen. Sie können wieder
auf die Seite "Live Video" und tippen Sie auf "Alarm" am unteren Rand des Bildschirms, um die
Fotos auszuprobieren.
5.3. Setzen Sie die SD-Karten-Videoaufzeichnung auf der Grundlage der Bewegungserkennung
wie folgt ein:
Schritt 1: Tippen Sie auf die Einstellung "Live Video" und wählen Sie dann "Advance Config"
oder "Device Settings".
Schritt 2: Gehen Sie auf "SDCard Record Config" -Seite und wählen Sie "On Alarm", dann
setzen Auflösung und Dateilänge. Die Aktivierung von "Record sound" und "Loop Recording"
ist ebenfalls möglich.
Schritt 3: Tippen Sie auf "OK", um die Motion Detection Video Recording-Einstellung
abzuschließen.
Schritt 4: Wenn die Bewegung erkannt wird, schaltet die Kamera eine Alarmmeldung an Ihr
Telefon oder Mobilgerät und zeichnet ein Video automatisch in den internen Speicher der
Kamera auf. Sie können auf die Seite "Live Video" zurückkehren, tippen Sie auf "Record" am
unteren Rand des Bildschirms und tippen Sie dann auf "Remote SD Card" oder um die
Videodateien auszuprobieren.
[Hinweis]:
1) Video Auflösung: 1280 × 720P, 640x480, 320x240 Video Format: ASF
2). Wenn aus irgendeinem Grund die Videodateien nicht im internen Speicher gespeichert werden
können, können Sie den Speicher formatieren, indem Sie auf "Format" tippen.
VI. Aufnehmen von Video auf Smartphone oder Tablet PC
>> Bitte stellen Sie sicher, dass die Kamera der APP in LAN oder WAN hinzugefügt wird,
bevor Sie beginnen.
6.1. Starten Sie die "BVCAM" APP. Tippen Sie auf das Kamerasymbol, um in den
Live-Videobildschirm zu gelangen.
6.2. Tippen Sie auf die Aufnahmetaste und die Audio-Taste , um die Aufnahme
zu starten oder zu stoppen.
Für Android-Benutzer werden die Videodateien im Flash-Speicher des Mobilgeräts
gespeichert. Bei IOS-Benutzern werden die Videodateien nur im APP "BVCAM" gespeichert.
6.3. Gehen Sie zurück zur Seite "Live Video", tippen Sie auf "Record" am unteren Rand des
Bildschirms und tippen Sie dann auf "Local" oder um die Videodateien auszuprobieren.
[Anmerkung]: Videoauflösung: 1280 × 720P, 640x480, 320x240 Videoformat: ASF
VII. Aufnehmen von Video auf lokale Micro SD-Karte
>> Bitte stellen Sie sicher, dass die Kamera der APP im LAN- oder WAN-Modus hinzugefügt
wird, bevor Sie beginnen.
7.1. Starten Sie die "BVCAM" APP.
7.2 Tippen Sie auf die Einstellung "Live Video" und wählen Sie dann "Advance Config" oder
"Device Settings".
7.3 Gehen Sie auf "SD Card Record Config" -Seite, dann legen Sie einen gewünschten
Aufnahmemodus und Dateilänge. Die Aktivierung von "Record sound" und "Loop Recording"
ist ebenfalls möglich.
7.4 Tippen Sie auf "OK", um die SD-Kartenaufzeichnungseinstellung abzuschließen, und die
Kamera nimmt das Video auf den internen Speicher auf.
7.5. Die Videodateien werden im internen Speicher dieser Kamera gespeichert. Sie können
die Videodateien nach Kapitel 5.3 ausprobieren.
VIII. Zurücksetzen
Wenn aus irgendeinem Grund die Kamera nicht mehr funktioniert oder nicht richtig
funktioniert, können Sie die Kamera zurücksetzen, um sie wieder in den normalen Betrieb
zurückzusetzen.
Bedienung: Wenn die Kamera eingeschaltet ist, halten Sie die Reset-Taste für 3 Sekunden
gedrückt, bis die blaue und rote Anzeige leuchtet. Die Kamera startet automatisch mit den
Standardeinstellungen innerhalb von 1 Minute.
IX. Umbenennen von Kamera & Ändern des Passworts
>> Bitte bestätigen Sie, dass die Kamera der APP hinzugefügt wird, und es ist online im
P2P (LAN) Modus, bevor Sie starten.
9.1. Starten Sie die "BVCAM" APP.
9.2. Ändern Sie den Kameranamen wie folgt:
Schritt 1: Tippen Sie auf das Einstellungssymbol auf der Seite "Live-Video" und wählen Sie im
Popup-Fenster "Gerät ändern" oder "Geräteeinstellungen".
Schritt 2: Löschen Sie den Standardnamen und geben Sie Ihren gewünschten Namen wie
Haus, Büro, Schlafzimmer usw. ein.
Schritt 3: Tippen Sie auf "OK" oder "√", um die Änderung zu bestätigen.
9.3. Ändern Sie das Passwort wie folgt:
OPTION 1
Schritt 1: Tippen Sie auf das Kamerasymbol auf der Seite "Live Video" und tippen Sie im
Popup-Fenster auf "Ändern".
Schritt 2: Geben Sie das neue Passwort ein und bestätigen Sie es, dann tippen Sie auf
"OK", um die Änderung zu speichern.
OPTION 2
Schritt 1: Tippen Sie auf das Symbol "Live Video", tippen Sie auf "Advance Config" oder
"Device Settings" und dann auf "Change P2P access password" oder "Change password"
-Seite.
Schritt 2: Geben Sie zuerst das Standard-Passwort "8888" ein, geben Sie dann ein neues
Passwort ein und bestätigen Sie es, tippen Sie auf "OK", um die Änderung zu speichern.
Häufig gestellte Fragen
Q1: Warum kann ich das WIFI-Signal der Kamera nicht auf meinem Smartphone oder
Tablet PC finden?
A1: Es gibt 4 Lösungen für dieses Problem:
1. Stecken Sie die Kamera mit dem mitgelieferten Netzteil in eine Steckdose. Warten Sie
1 Minute, bis das WIFI-Signal SSID erscheint.
2. Setzen Sie die Kamera zurück (siehe VIII) und warten Sie dann, bis das WIFI-Signal
SSID angezeigt wird.
3. Halten Sie Ihr Telefon oder Mobilgerät in der WIFI-Hotspot-Reihe der Kamera und
erfrischen die WIFI-Signalseite. Es kann bis zu 1 Minute dauern, bis der Hotspot auf der
Telefon- oder Mobiltelefon-WIFI-Einstellungsseite erkennbar wird.
4. Schalten Sie die WIFI-Funktion Ihres Telefons oder des Mobilgeräts für eine Weile aus,
und schalten Sie es dann wieder ein.
Q2: Warum funktioniert das WAN-Modus-Setup?
A2: Bitte stellen Sie sicher, dass Ihr Netzwerk in einem guten Zustand ist. Plus, das
WIFI-Netzwerk die Kamera ist konfiguriert mit kann nicht das gleiche mit einem Sie Ihr
Telefon zu verbinden.
Q3: Was kann ich tun, wenn ich das Passwort vergessen habe?
A3: Bitte die Kamera zurücksetzen (Siehe VIII)
Q4: Die APP kann die UID der Kamera nach der Auswahl von "Search (LAN)" nicht
finden?
A4: Stellen Sie sicher, dass Ihr Telefon oder Mobilgerät immer noch mit dem WIFI-Signal
der Kamera verbunden ist. Vergewissern Sie sich, dass die Kamera mit der Steckdose
versorgt wird oder die Kamera vollständig aufgeladen ist.
Q5: Warum Live-Video-Bildschirm zeigt sich schwarz und ein Suchkreis dreht sich in
der Mitte, aber nichts zeigt jemals?
A5: a. Wenn Ihre Kamera mit einem langsamen WIFI-Netzwerk verbunden ist, warten Sie
10-30 Sekunden, bis das Live-Video erneut angezeigt wird.
B. Wählen Sie auf der Live-Videoseite eine niedrigere Auflösung aus.
Q6: Live Video ist nicht glatt und klar?
A6: Wählen Sie eine geeignete Auflösung entsprechend der Echtzeit-Netzwerkumgebung
aus.
Q7: Wie viele mobile Geräte können gleichzeitig mit der Kamera verbinden?
A7: keine Begrenzung.
Q8: Es gibt nur 1 Benutzer, aber die Kamera zeigt 2 oder mehr Benutzer?
A8: a. Wenn Sie sich sehr oft anmelden, ist der letzte Login-Datensatz noch in. Wenn Sie
es alle 2-5 Minuten überprüfen, zeigt die Kamera sicher die genaue Anzahl der Benutzer.
B. Für Ihre Sicherheit und Privatsphäre, bitte ändern Sie das Passwort der Kamera für die
fi nde Zeit verwenden.
Q9: Wie viele Kameras werden auf der mobilen Applikation unterstützt?
A9: keine Begrenzung.
Q10: Gibt es irgendeine PC-Client-Software, die ich auf meinem Computer verwenden
kann?
A10: Bitte klicken Sie auf den PC-Client-Software-Download-Link und laden Sie die Zip-Datei
auf Ihren PC herunter:
Http://www.wiseupshop.com/download?name=dvr-0031-4&Submit=++++++++
Q11: Die Kamera hält meine WIFI-Einstellungen nicht und zeigt weiter, dass die Kamera
offline ist?
A11: Stellen Sie sicher, dass die Kamera im Bereich des guten WIFI-Signals liegt. Oder
überprüfen Sie, ob der Netzadapter für längere Zeit richtig angeschlossen ist.
Q12: Wird die Kamera immer noch funktionieren, wenn die Stromversorgung erlischt?
A12: Wenn sich die Kamera im P2P-Modus befindet, kann die Kamera immer noch arbeiten
und Videos aufnehmen, solange die Kamera noch geladen ist. Wenn sich die Kamera im
WAN-Modus befindet, funktioniert es erst, wenn die Stromversorgung wiederhergestellt ist und
der Internetzugang verfügbar ist.
Q13: Wie füge ich die Kamera zu mehr Geräten hinzu?
A13: Stellen Sie sicher, dass sich die Kamera bereits im WAN-Modus befindet. Dann
starten Sie die "BVCAM" APP auf Ihrem anderen Android-Handys oder Tablet-PCs, tippen
Sie auf "+" -Symbol, geben Sie die Kamera UID (eine einzigartige Kombination von Zahlen
und Buchstaben für Ihre Kamera). Schließlich tippen Sie auf "OK", um die Kamera zur APP
hinzuzufügen.
Q14: Welche Media Player Software soll ich verwenden, um die Videodateien auf meinem
Computer wiederzugeben?
A14: Klicken Sie auf den Link: http://www.videolan.org/vlc/index.html, um den VLC-Player
herunterzuladen und zu installieren, um Videodateien auf Ihrem PC oder Mac-Computer
wiederzugeben.
Q15: Wie kann ich die Videodateien im internen Speicher der Kamera lesen?
A15: Du kannst zurück zur Seite "Live Video" gehen, am unteren Bildschirmrand auf "Record"
tippen und dann auf "Remote SD Card" tippen oder die Videodateien ansehen. Oder Sie
können die Videodateien auf Ihr Smartphone herunterladen.