Wisper 905 ECO User manual

Page|1

Wisper905EcoInstallationManual

1. Prepareaclearspacetoinstallyourbike.

2. Unpackyourbikeandcomponentsfrom
theWispershippingboxandleanthe
semi‐assembledbikeupside‐downagainst
awall(orchair)soitwon’ttip.

3. YourWispershippingboxwillcontain:
mainbikeframeassembly,seatand
seatpost,twosmallcardboardboxes.The
smallestboxcontains:pedals,2Xkeys,
biketoolkit.Theotherboxcontainsyour
batterycharger.

4. Useapairofnippersorscissorsandcarefullysniptheplastictiesholdingthefrontwheelto
theframe.Placethewheelnearby.

5. Carefullyliftandturnthebikerightwayupandagainleanitagainstitssupport.Snipthe
threeplastictiesholdingthehandlebarstotheframeandlowerthehandlebarstothe
ground.Carefullyremoveallprotectivefoamandpaddingfromthebike(scissorsareuseful
here,butbeextremelycarefulnottoscratchtheframe,ordamageanycables).

6. Usethekeyssuppliedandunlockthebatterylock.Makesure
thebatterypoweroutputcableisunpluggedfromthe
battery,thenopenoutthebatteryhandleandpullthe
batteryuptoslideitfreefromthebike.
Important:Fullychargethebatterybeforeusingthe
bike.RefertotheUserGuideforinstructions.
Important:Yourfirstthreechargecyclesneedtobe
deepcycles,asdetailedintheUserGuide.


7. Hint:Itisagoodideatobeginchargingthebatterynow,so
itisreadysooner.Tochargethenewbattery,unpackthe
chargerfromthelargerofthecardboardboxes.Remove
therubberchargesocketprotectivecapfromthebattery
(nexttothepowerterminalsocket)and,withtheI/O
switchonthechargeroff(O),plugthechargerleadinto
thechargesocketonthebattery.

Page|2


8. Nowplugthechargerintoapowerpointandturnonthepoweratthewall.Lastly,switchon
thecharger(thecharger’sO/Iswitchisnexttothe110/240vpowerinputcable).Onelight
willshowred,andtheotherwillshoworange(charging).Theorangelightwillturngreen
whenthefast‐chargecycleiscomplete.Itisbesttochargeovernightforthefirst3charge
cycles,asdetailedintheuserguide.
Note:Whencharging,alwaysthelaststepistoswitchthechargerswitchon.This
allowsthechargertoproperlysensethebatterychargelevels.




9. Slidethehandlebarheadsetstem‐postintothe
bikeframe.Alignthehandlebarswiththeforks
thenusethelargestallenkeysuppliedtotighten
thenutontopofthestem‐post.



10. Carefullyturnthebikeupside‐downandlayitonarug,orsoftsurfacetoavoiddamage.


11. Removetheplasticaxlerestfromthebaseofthefrontforks.


12. Cliptheplastictieholdingthefrontforkbrakecalliperstogether.


13. Removetheprotectiveend‐capfromtheaxleofthefrontwheelandloosentheaxlenuts
untiltheyareneartocomingofftheendsoftheaxle.


14. Carefullyslotthefrontwheelaxleintotheforks,guidingthetyrebetweentheopenbrake
callipers.

15. Firmlytightentheaxlenutsusingthespannersupplied.
Important:Ifyouarenotfamiliarwithbike
maintenance,thenpleasehaveyourlocalbike
storespecialistcheckyourbikebeforeridingit.
Incorrectlyinstalledcomponentscanbe
dangerous.




Page|3


16. Reinstallthebrakecableintothev‐brakecallipercablemount..

Note:ifthisprovestoodifficult,youmayneedto
loosenthecablenutandslackenthecable.Then
youcaneasilyslotthecableintothecablemount.
Important:Re‐setthecableandtightenthecable
nutfirmly.Thepadsshouldbeascloseas
possibletotherimswithoutrubbing.
Note:Asnewbrakecablesstretch,youcan
retightenthemeasilybyscrewingoutthecable
tensionadjuster(thescrewcapwherethebrake
cableentersthehandlebarbrakeleverunit).
Remembertoloosenthelocknutringfirst.


17. Carefullyliftandturnthebikebacktoanuprightposition.Lowerthekickstandtostabilise
thebike.

18. Unpackthepedalsandcheckontheaxle‐endsto
seewhichisleft(L)andwhichisright(R).

19. Threadthepedalsintothecorrespondingcrank
andtightenfirmlyusingthesupplied15mm
wrench.
Hint:Becarefultonotewhichcrankis
actuallytherightandwhichistheleft
whenthebikeisfacingforwards.



20. Nowyourinstallationiscomplete.DonotrideyoureBikeuntilyouhavereadtheUserGuide
forfullinstructionsoncorrecteBikeuse.

21. Wisper Bikes ltd, and or any of its distributors, do not accept any legal liability for accident or
injury caused by improper installation of any of the components utilised on this electric
bicycle. If you are not fully competent with bicycle maintenance and tuning procedures, you
must have your bike checked over by a qualified bicycle technician before riding it.
This disclaimer does not affect your statutory rights.
