Wittkopp Primor 1000 User guide

Primor 1000
Installer manual
Installation and commissioning instructions
en_02 P1000-Part 2b-Installer manual V2.01
1 / 6
Note:
On the cover sheet you can find warning information, and an explanation of the symbols and
terms used, together with the exclusion of liability.
Contents
General................................................................................................................................. 2
Preparation for installation..................................................................................................... 3
Installation dimensions for lock 1000................................................................................. 3
Preparation of the boltwork / door...................................................................................... 3
Installation............................................................................................................................. 4
Wiring / installation................................................................................................................ 4
Connecting the Primor Signal plus..................................................................................... 5
Function test.......................................................................................................................... 5
Input of the opening code.................................................................................................. 5
Keypad test ....................................................................................................................... 6
Mount the keypad before installing the electronic lock. All the keypads of the Primor series
can be used. For information on how to install the keypads, please refer to "Part 2a- Primor
keypad installer manual".

Primor 1000
Installer manual
Installation and commissioning instructions
en_02 P1000-Part 2b-Installer manual V2.01
2 / 6
General
P1000 series locks have standard
installation dimensions and can be installed
in all 4 installation positions (right, left, top,
bottom). They are designed for boltworks
with a one-sided locking edge, i.e. only for
force absorption by the straight boltwork
flank of the quarter-circle-shaped bolt.
They are intended to be installed in safes
made of metal.
The electronic lock requires no
maintenance in a normal residential or
office environment. We recommend a
security and function test of the electronic
lock after around 10,000 closing actions.
It is essential that the lock is protected
against attacks from outside. It is
recommended to protect the security-
relevant parts of the high-security lock
against access even when the safe door is
open
It is not permissible to use two locks of the
same type with analogue keypads without
any additional components for lock status
detection.
Do not apply any lubricants or other
substances to the lock.
Always follow the following sequence for installation:
•Check the preconditions for installation
•Wiring / installation of the cables
•Connect the power supply
•Function test of the locking mechanism
•Perform all settings (user installation, delay time)
Ensure that the load limits are not exceeded at any time.
You can find the corresponding values in Annex C "Technical data".

Primor 1000
Installer manual
Installation and commissioning instructions
en_02 P1000-Part 2b-Installer manual V2.01
3 / 6
Preparation for installation
Installation dimensions for lock 1000
Preparation of the boltwork / door
To install the lock, there must be four
threaded holes for fastening on the
boltwork or inside the safe door. The
electronic lock must be fastened with the
supplied screws or M6 or 1/4” cylinder
screws (min. strength class 8.8). The screw
length should be measured so that a
minimum screw-in depth of 6 mm is
possible.
Drilling pattern:
The electronic lock can be installed in the area of openings with a maximum diameter of 11
mm around the axis centre shown above.
Primor 1000/1600/2000: this hole can be omitted
Primor 100 / 2000: Centre of electronic lock drive is flush with centre of
input unit (Primor RO)/centre of keypad lever (Primor RE)

Primor 1000
Installer manual
Installation and commissioning instructions
en_02 P1000-Part 2b-Installer manual V2.01
4 / 6
Installation
The retaining screws must be tightened in
such a way that a permanent and firm hold
is ensured.
Tighten the fastening screws with a
maximum torque of 3.5 - 5 Nm. To prevent
the screws from becoming loose, we
recommend using screw locking agents
(adhesive).
There must be no tension or pressure on
the lock bolt after installation.
Make sure there is sufficient clearance to
the locking point.
Wiring / installation
The Primor 1000 locks can be externally
powered with Primor Signal plus.
When supplied by a power supply unit, the
charge status of the inserted battery is not
monitored.
Emergency power supply (optional): Insert
the 1 x 9V alkaline block battery.
Disconnect the power supply, including that from batteries, before starting any work or
making any changes to the wiring between the lock, keypad or signal boxes.
External battery compartment / signalbox
Input unit

Primor 1000
Installer manual
Installation and commissioning instructions
en_02 P1000-Part 2b-Installer manual V2.01
5 / 6
Connecting the Primor Signal plus
It is always connected with the second port
(see above) if
•the lock system has an external
power supply,
•a "silent alarm" contact is used to
evaluate a hazard notification
system,
•a system disable function is to be
used by an external signal
(potential-free contact).
This requires the connection of additional
hardware.
The lock is compatible with all the available
components of the Primor series.
You can find informationon the wiring in the
instructions for the signal box.
Function test
Carry out a function test after completing all
the mounting and installation work.With the
door open, you should open and close the
lock several times using the master code
that has been set at the factory.
The relationship between easy opening and
reliable closing can be set using the
operating lever of the boltwork.
The locking check can be done via the
operating lever of the boltwork and should
be performed after each closing and
locking.
Input of the opening code
e.g. master factory code


=✓
→

The opening code can be entered
directly as described above, without
selection. The bolt is released for
approx. 3 seconds after a valid
code has been entered. Open the
container with the valuables within
this time after inputting the code.
=


Primor 1000
Installer manual
Installation and commissioning instructions
en_02 P1000-Part 2b-Installer manual V2.01
6 / 6
Keypad test
We recommend a final keypad test using function menu 5 to ensure that all the numeric keys
function properly.
 ☼Checking the menu system
Press the keys in the
sequence
…

=✓
Press each numeric key once. A
functional key is indicated by a
double signal tone.
A key that is not recognised is
indicated by a long signal tone and
the function test is terminated. The
system must be checked.