Wittkopp Anchor 4000 Series User guide

Anchor 4000
Installer manual
Installation and commissioning instructions
en_A4000-Teil 2-Errichterhandbuch V2.03.docx
1 / 7
Note:
On the cover sheet you can find warning information, and an explanation of the symbols and
terms used, together with the exclusion of liability.
Contents
General................................................................................................................................. 2
Preparation for installation..................................................................................................... 3
Installation dimensions...................................................................................................... 3
Preparation of the boltwork / door...................................................................................... 3
Installation............................................................................................................................. 4
Wiring / installation................................................................................................................ 5
Connection of an analog keypad ....................................................................................... 5
Connection P- signal plus / UART ..................................................................................... 6
Function test.......................................................................................................................... 6
Input of the opening code.................................................................................................. 6
Keypad test ....................................................................................................................... 7
System setup ........................................................................................................................ 7
Mount the keypad before installing the electronic lock. All the keypads of the Primor series
can be used. Details on installing the keypads are given in the "Primor installation
instructions (see sections 3 to 7)".

Anchor 4000
Installer manual
Installation and commissioning instructions
en_A4000-Teil 2-Errichterhandbuch V2.03.docx
2 / 7
General
Locks of the Anchor 4000 series have
standard installation dimensions and can
be mounted in all 4 installation positions
(right, left, top, bottom). They have been
designed for a boltwork with two blocking
edges, i.e. for the force to be applied only
on only the flank of the bolt.
They are intended to be installed in safes
made of metal.
The electronic lock requires no
maintenance in a normal residential or
office environment. We recommend a
security and function test of the electronic
lock after around 10,000 closings.
For security reasons it is not permissible to
install the electronic lock in the area of the
cutouts in the safe door.
It is essential that the lock is protected
against attacks from outside. We
recommend that you protect against access
the security-relevant parts of the high-
security lock also when the door of the
container that holds the valuables is open.
It is not permissible to use two locks of the
same type in connection with analog
keypads without any additional
components for locking state detection.
Do not apply any lubricants or other
substances to the lock.
Always use the following sequence for installation:
•Check the preconditions for installation
•Wiring / installation of the cables
•Set up the power supply
•Function test of the locking mechanism
•Make all the settings (user system, Dualcode, inputs and outputs, delay time)
Ensure that the load limits are not exceeded at any time.
You can find the corresponding values in Annex C "Technical data".

Anchor 4000
Installer manual
Installation and commissioning instructions
en_A4000-Teil 2-Errichterhandbuch V2.03.docx
3 / 7
Preparation for installation
Installation dimensions
Preparation of the boltwork / door
For installation of the lock there must be
three threaded holes with 5 mm screw-in
depth for attachment to the boltwork or
within the safe door. The electronic lock is
to be attached with the supplied M6 or 1/4"
screws or cylinder screws (minimum
strength class 8.8).
The length of the screws must be 25 mm or
more so that a minimum screw-in depth of
5 mm is attained.

Anchor 4000
Installer manual
Installation and commissioning instructions
en_A4000-Teil 2-Errichterhandbuch V2.03.docx
4 / 7
Installation
The included toothed lock washer must be
used to attach the lock. To do this, turn the
screws by a few turns, but only so far that
movement in the direction of the bolt is still
possible. Push the lock in the direction of
the bolt without any play up to the edges of
the strikers of the boltwork and tighten up
the retaining screws. The position must be
selected such that the sliding striker of the
boltwork runs over the entire opening path
on the slanted sliding surfaces of the bolt
and when fully open on the bolt head.
Tighten up the retaining screws so as
to ensure a permanent and secure hold.
The screw heads must be within the
recesses provides. Mounting with a
screwing-in direction from the chassis floor
is not permitted.
Striker edges
plates

Anchor 4000
Installer manual
Installation and commissioning instructions
en_A4000-Teil 2-Errichterhandbuch V2.03.docx
5 / 7
Tighten up the fastening screws to a
maximum torqueof 10 Nm. We recommend
the use of a bolt locking agent (adhesive) to
prevent the screws from coming undone by
themselves.
The bolt of the lock may not be under
tension or pressure after installation.
Wiring / installation
If the lock is operated outside the area of
validity of the VdS, then signal boxes,
external power supplies, etc. can be used
with the Anchor in addition to all the analog
keypads that are compatible with the
Primor series. The VdS approval is
restricted to operation with input units of the
Primor FS, FL, RO and RE series.
Connection of an analog keypad
As supplied, onlythe interface for an analog
keypad from the Primor series is active. If
the lock is to communicate with a digital
input unit, i.e., an "intelligent" one, then
additional settings are required in the setup
menu [6] in addition to the selection of the
corresponding interface or socket.
You can find the corresponding commands
in the user manual.
You can find information on inserting the
battery in the operating manual of the
corresponding Primor keypad.
.
analog keypad
e.g. Primor RO
serial interface [UART] or
[IO] for Alarmbox
Cut off the power supply, including that from batteries, before starting any work or making
any changes to the wiring between the lock, keypad or signal boxes.

Anchor 4000
Installer manual
Installation and commissioning instructions
en_A4000-Teil 2-Errichterhandbuch V2.03.docx
6 / 7
Connection P- signal plus / UART
Connection via the second port (see above)
is always done if
the lock system has an external
power supply,
a "silent alarm" contact for
evaluation by an alarm system has
been made available,
a system block by an external
signal (dry contact) is to be used.
Additional hardware is required to do this.
The lock is compatible with all the available
components of the Primor series.
You can find informationon the wiring in the
instructions for the signal box. The VdS
approval is no longer valid when used in
conjunction with a signal box or if the serial
interface (UART) is not used correctly.
Function test
Carry out a function test after completing all
the mounting and installation work.With the
door open, you should open and close the
lock several times using the master code
that had been set at the factory.
The relationship between easy opening and
reliable closing can be set via the operating
lever of the boltwork.
The locking check can be done via the
operating lever of the boltwork and should
be performed after each closing and
locking.
Input of the opening code
e.g. factory code Master


=
→

The opening code can be input
directly as described above, without
selection. After a valid code is input
the lock releases the bolt
movement for around 3 seconds.
Open the container with the
valuables within this time after
inputting the code.
=

If a signal block with "active release" (switching logic) has been set up this ensures that the
blocking is not switched off if the control cable iscut through. At the same, a cable breakage
within the safe always thus entails the risk of a blockade.

Anchor 4000
Installer manual
Installation and commissioning instructions
en_A4000-Teil 2-Errichterhandbuch V2.03.docx
7 / 7
Keypad test
We recommend a final keypad test using function menu 5 to ensure that all the numeric keys
function properly.
 ☼Checking the menu system
Press the keys in the
sequence
…

=
Press each numeric key once.
A functional key is indicated by a
double signal tone.
A key that is not recognised is
indicated by a long signal tone and
the function test is terminated. The
system must be checked.
System setup
The setting options and the control sequences that are required are described in the user
manual.
We therefore recommend the following procedure:
Setup of the users [menu 1]
if applicable, parameterisation of the inputs and outputs [menu 6]
if applicable, setting up the Dualcode condition [menu 6]
if applicable, setting up the delay time [menu 9]
In particular, the user system can be made markedly faster by using setup mode [menu 8].
The repetitive input of the master code is then restricted to selecting setup mode.