Wittkopp Primor Series User manual

Primor xxxx
Operator manual
Instructions for system and user administrators
03 Pxxxx - Operator manual V2.03
1 / 8
Note:
On the cover sheet you can find warning information, and an explanation of the symbols
and terms used, together with the exclusion of liability.
Contents
General...........................................................................................................................2
Code length / silent alarm............................................................................................2
Battery.........................................................................................................................2
Interfaces ....................................................................................................................2
Dual code + delay time................................................................................................2
Penalty time.................................................................................................................2
Overview of user rights................................................................................................3
Opening ..........................................................................................................................3
P1000 / P1600.............................................................................................................3
P2000 / P2600.............................................................................................................3
P30xx..........................................................................................................................4
Opening with dual code...................................................................................................4
Opening with active delay time........................................................................................5
Triggering a silent alarm..................................................................................................5
Menu functions................................................................................................................6
0 Change code............................................................................................................6
1 Create user...............................................................................................................6
2 Operating lock ..........................................................................................................7
3 Delete user...............................................................................................................7
5 Check system...........................................................................................................7
7 Overview of users.....................................................................................................8
9 Set time delay...........................................................................................................8

Primor xxxx
Operator manual
Instructions for system and user administrators
03 Pxxxx - Operator manual V2.03
2 / 8
General
Depending on the setup, the opening of
the lock can be subject to additional
restrictions. A combination of these
restrictions is also possible:
1. Delay time → Opening is only
possible once a defined delay
time has come to the end (with
the exception of user 9).
2. Dual code → Opening is only
possible with two valid user
codes. (also the "two pairs of
eyes" principle )
The dual code / the “two pairs of eyes”
principle cannot be disabled by the user
and is set at the factory [level 25].
Code length / silent alarm
Normally each user code has a length of
6 digits (0-9) [level 5]. If a silent alarm is
configured [level 15], the number of code
digits increases to 7 digits. The 7th code
digit is therefore shown in grey in the
following description. It is triggered by
changing the last code digit.
Battery
The lock is powered by a9V block battery
(alkaline-manganese).
A warning signal is emitted after code
input if the battery charge is too low. A
warning tone is repeated several times
with an alternately flashing red LED.
In such a case, change the battery as
soon as possible. The programmed
codes are retained while the battery is
changed.
Interfaces
For locks configured to level 5, only the
interface for analogue input units is
active. The second connection can only
be used for power supply via a signal box
or power supply unit.
Locks with level 15 have the silent alarm
function preconfigured. This means the
alarm contact is routed via the second
connection with a corresponding
hardware [signal box] and a lock disable
function is available via an input.
Dual code + delay time
When the dual code is activated, the lock
is opened according to the described
opening procedure after the delay time
has elapsed.
"User 9" can open alone during the delay
time if the dual-code condition (“two pairs
of eyes” principle) [level 25] is active. A
dual-code condition arises through the
fact that user 9 alone cannot start the
delay time.
An invalid code input during the release
time means that the operation is
terminated and the delay time must be
started again.
The input of a valid code during the
opening delay is acknowledged positively
but has no effect in itself. An opening
delay time that has been started can be
aborted by pressing any key.
Penalty time
After 4 invalid code entries there is a
penalty time of 5 min. Until a valid code is entered, a penalty time is then triggered again after each two incorrect entries.

Primor xxxx
Operator manual
Instructions for system and user administrators
03 Pxxxx - Operator manual V2.03
3 / 8
Overview of user rights
Opening
P1000 / P1600
This type of lock has a swing bolt. This
means once the locking mechanism has
been released, the bolt is pushed out of
the locking position by the bolt
movement. When the boltwork is closed,
the lock bolt also returns automatically to
the locking position under spring load.
The lock is closed automatically without
any further action needed by the user.
P2000 / P2600
A full deadbolt is driven via an axis from
the outside with a rotating keypad
housing or an additional operating lever.
The lock's internal locking mechanism
releases the rotary movement for approx.
3 sec if a valid opening code has been
detected and all secondary conditions
(no locks active) are fulfilled. The lock
must be closedmanually by the user after
the boltwork has returned to the closed
position.
Factory code
Opening
Start delay time
Quick opening code
Create user
Change code
Delete user
Trigger operating lock
Check system
Overview of users
Set delay time
Master
123456(0)
⚫
⚫
⚫
⚫
⚫
⚫
⚫
⚫
⚫
User 0...8
-
⚫
⚫
⚫
⚫
User 9
-
⚫
⚫
⚫
⚫

Primor xxxx
Operator manual
Instructions for system and user administrators
03 Pxxxx - Operator manual V2.03
4 / 8
P30xx
Motorised locks from the P30xx series
feature a spring-loaded deadbolt. This
means, after opening, the dead bolt drive
is moved back into the closing position
after approx. 3 sec. If the bolt travel is not
in the locking position again, i.e. the bolt
cannot yet retract into the free slot, it
rests against the locking edges of the
boltwork under spring load. When the
boltwork is closed, the bolt then jumps
into the locking position and locks
automatically without further action
required by the user.
e.g. master factory code


=✓
→

The opening code can be entered
directly as described above, without
selection. The bolt is released or
retracted for approx. 3 seconds
after a valid code has been
entered. Open the safe within this
time after entering the code.
=

Opening with dual code
e.g. user 3 with code 0303030starts to enter their code
If the code is entered incorrectly or
if more than 30 seconds elapse
between the two code inputs then
the code input is terminated with a
long signal tone.


=✓
=
The "two pairs of eyes" principle, here user 5 with
code 0505050, triggers the opening


=✓
→

=
→

The locking check can be done via the operating lever of the boltwork and should be
performed after each closing and locking. (With the exception of P2000, lock check is
possible using keypad position or operating toggle)

Primor xxxx
Operator manual
Instructions for system and user administrators
03 Pxxxx - Operator manual V2.03
5 / 8
Opening with active delay time
Start by entering code


=✓
→

If a delay time has been
programmed, this must be started
first by entering a valid opening
code. It can then be opened by
entering any desired valid user
code during the time window for
opening.
User 9 cannot start the delay, but
instead can open before the end of
the delay time.
=
♪…2 sec…♪…2 sec…♪…2
sec…

♪…1 sec…♪…1 sec…♪…1
sec…

Enter the code for opening


=✓
→

=
→

Triggering a silent alarm
e.g. opening code 1234567
Start by entering code


=✓
→

The last code digit is changed in
each case if "silent alarm" is active.
The calculation is based on the
scheme: last digit + 1
With a 9 as the last code digit, the 0
triggers the alarm.
→

=
→

The locking check can be done via the operating lever of the boltwork and should be
performed after each closing and locking. (With the exception of P2000, lock check is
possible using keypad position or operating toggle)

Primor xxxx
Operator manual
Instructions for system and user administrators
03 Pxxxx - Operator manual V2.03
6 / 8
Menu functions
If there is a rejection at the end of a menu step (long signal tone) then the procedure is
terminated and the menu function is quit.
0 Change code
e,g. change 1234560to 1111111
 ☼Change code menu
Enter code, e.g.


=✓
Both the user code and the master
code can be changed by using the
Change function.
Enter the new code


=✓
Confirm the new code


=✓
Code was changed successfully
1 Create user
e.g. create user no. 3
 ☼Create user code
Enter the master code


=✓
A new user code is only accepted if
the code differs at two places by
one digit from an existing code.
If an opening delay has been
programmed, user 9 for the
immediate opening code can only
be created in the opening release
time.
Number of the user to be
created


=✓
Enter user code, e.g.


=✓
Confirm the user code


=✓
In the case of an active dual code a valid user code must be entered before opening a
menu. A menu is only selected afterwards.

Primor xxxx
Operator manual
Instructions for system and user administrators
03 Pxxxx - Operator manual V2.03
7 / 8
2 Operating lock
 ☼Operating lock menu
All users can be blocked or
released with this function. All
codes are retained.
Enter the master code


=✓
All users are activated / deactivated
3 Delete user
e.g.delete user no. 2
 ☼Delete user menu
Enter the master code


=✓
The master can delete a user. It is
not possible to delete the master.
Number of the user to be
deleted


=✓
5 Check system
 ☼Check system menu
Press the keys in the
sequence
…

=✓
Press each numeric key once. A
functional key is indicated by a
double signal tone.
A key that is not recognised is
indicated by a long signal tone and
the function test is terminated.
The system must be checked.
When the dual code is active, the user who made the menu entry possible by entering a
code cannot be deleted.

Primor xxxx
Operator manual
Instructions for system and user administrators
03 Pxxxx - Operator manual V2.03
8 / 8
7 Overview of users
 ☼Overview of users menu
Enter the master code


=✓
This function gives an overview of
the number of free and already
occupied users.
It is possible to check selectively
whether one or more specific users
have already been created.
User number to be checked
,,...
♪

= free
=
occupied
End the query


=✓
9 Set time delay
e.g. 10 min time delay with an opening window of 5 min
 ☼Delay time menu
Enter the master code


=✓
The opening delay time can be
increased at any time. A reduction
or a deactivation of the opening
delay time is only possible
during the release time.
To deactivate the delay, set the
delay time to 00 and the release
time to 01.
Range of values:
Delay time 01 to 99 min.
Release time 01 to 19 min.
Set the delay time

Release time


=✓
Confirm the delay time

Confirm the release time


=✓