woodmizer MP260EA13U-V User manual

WARNING! Read and understand this
manual before using this machine.
!
Wood-Mizer® Moulder Planer
Safety, Setup, Operation,
and Maintenance
MP260EA13U-V rev. B1.01
MP260EB13U-V rev. B1.01
Safety is our #1 concern!
Form #2411-US

Active Patents assigned to Wood-Mizer, LLC
Wood-Mizer, LLC has received patents that protect our inventions which are a result of a dedication to
research, innovation, development, and design. Learn more at: woodmizer.com/patents
©2021 Wood-Mizer LLC
Printed in the United States of America, all rights reserved. No part of this manual may be reproduced in any form by any
photographic, electronic, mechanical or other means or used in any information storage and retrieval system without
written permission from
Wood-Mizer, LLC
8180 West 10th Street
Indianapolis, Indiana 46214
California
Proposition 65 Warning
WARNING:
Breathing gas/diesel engine exhaust exposes you to chemicals known to
the State of California to cause cancer and birth defects or other reproductive harm.
Always start and operate the engine in a well-ventilated area.
If in an enclosed area, vent the exhaust to the outside.
Do not modify or tamper with the exhaust system.
Do not idle the engine except as necessary.
For more information go to www.P65warnings.ca.gov.
WARNING: Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the State of California to cause cancer. Avoid inhaling
wood dust or use a dust mask or other safeguards for personal protection.
For more information go to www.P65Warnings.ca.gov/wood.

Table of Contents Section-Page
Table of Contents MP260 12/9/21 iii
SECTION 1 GENERAL INFORMATION
1.1 How To Use The Parts List.................................................................... 1-1
SECTION 2 OVERVIEW
2.1 MP260 Components .............................................................................. 2-1
2.2 MP260 Additional Part Kit .................................................................. 2-2
SECTION 3 MECHANICAL ASSEMBLY
3.1 Covers ...................................................................................................3-1
3.2 Table MP260 ....................................................................................... 3-2
3.3 Right Spindle Assembly ....................................................................... 3-4
3.4 Bottom Cutterhead ............................................................................. 3-6
3.5 Infeed and Outfeed Fences .................................................................. 3-7
3.6 Feed Assembly .................................................................................... 3-8
3.7 Drive Shaft Assemblies .................................................................... 3-9
3.8 Slide Bearing Assembly .....................................................................3-10
3.9 Tension Plate ..................................................................................... 3-11
3.10 Cutterhead Assembly (Upper) .......................................................... 3-12
3.11 Bearing Housing ................................................................................. 3-13
3.12 Right Guard ..................................................................................... 3-14
3.13 Sawdust Outlet Guard ......................................................................... 3-15
3.14 Side Guard ........................................................................................... 3-16
3.15 Left Guard .......................................................................................... 3-17
3.16 Sawdust Outlet Guard ......................................................................... 3-18
3.17 Top Cover ......................................................................................... 3-19
3.18 Sawdust Outlet ................................................................................. 3-20
3.19 V-belt Cover ....................................................................................... 3-21
3.20 Spindle Moving Assembly ................................................................. 3-22
3.21 Pressure Roller Assembly II .............................................................. 3-24
3.22 Left Spindle Assembly ..................................................................... 3-25
3.23 Clamp Roller Assembly .....................................................................3-26
3.24 Side Feed Assembly ........................................................................... 3-27
3.25 Up/Down Feed Assembly ................................................................. 3-28
3.26 Up/Down Feed Scale ........................................................................... 3-30
3.27 Moveable Cutter Handle .....................................................................3-31
3.28 Up/Down Feed Handle ................................................................... 3-32
3.29 Feed Chain Tensioner ....................................................................... 3-33
3.30 Feed Chain Slide ................................................................................ 3-34
3.31 Rod Set ............................................................................................... 3-35
3.32 Moving Plate ...................................................................................... 3-36
SECTION 4 MOTOR KITS
4.1 Motor Kit ............................................................................................. 4-1
4.2 Side Cutter Motor Assemblies ............................................................. 4-2
4.3 Horizontal Upper Cutter Drive .......................................................... 4-4
4.4 Horizontal Bottom Cutter Drive ........................................................... 4-5

Table of Contents Section-Page
iv MP260 12/9/21 Table of Contents
4.5 Feed Drive .............................................................................................4-7
4.6 Electric Box Bracket ..............................................................................4-8
4.7 Electrical Box, MP260EA ...................................................................4-9
4.8 Electrical Box, MP260EB ................................................................4-10
SECTION 5 DECALS
5.1 Decals MP260 .................................................................................5-1
SECTION 6 OPTIONS
6.1 Infeed/Outfeed Tables .......................................................................6-1
6.2 Castors .................................................................................................6-3
6.3 Bushing Kit ...........................................................................................6-4

General Information
How To Use The Parts List 1
General Information WM doc 12/9/21 1-1
SECTION 1 GENERAL INFORMATION
1.1 How To Use The Parts List
Use the table of contents to locate the assembly that contains the part you need.
Go to the appropriate section and locate the part in the illustration.
Use the number pointing to the part to locate the correct part number and description in the
table.
Parts shown indented under another part are included with that part.
Parts marked with a diamond () are only available in the assembly listed above the part.
See the sample table below.
Sample Part #A01111 includes part F02222-2 and subassembly A03333.
Subassembly A03333 includes part S04444-4 and subassembly K05555.
The diamond (  ) indicates that S04444-4 is not available except in subassembly A03333.
Subassembly K05555 includes parts M06666 and F07777-77.
The diamond (  ) indicates M06666 is not available except in subassembly K05555.
To Order Parts:
Use your online Customer Gateway Account to find and order parts.
From the continental U.S., call 1-800-525-8100 to order parts. Have your customer number,
serial number (VIN when applicable), and part numbers ready when you call.
From international locations, contact the Wood-Mizer distributor in your area for parts.
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
SAMPLE ASSEMBLY, COMPLETE (INCLUDES ALL INDENTED PARTS BELOW) A01111 1
1Sample Part F02222-22 1
Sample Subassembly (Includes all indented parts below) A03333 1
2Sample Part (  Indicates part is only available with A03333) S04444-4 1 
Sample Subassembly (Includes all indented parts below) K05555 1
3Sample Part (  Indicates part is only available with K05555) M06666 2 
4Sample Part F07777-77 1

Overview
MP260 Components
2-1 12/9/21 Overview
2
SECTION 2 OVERVIEW
2.1 MP260 Components
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
MP260 PRO M4-SIDED MOULDER 230V 1P W/ FD MP260EA13U-V
-US
1
1Assy, MP260 Mechanical Assembly See Section Mechanical Assembly 537000-US 1
2Assy, Motor Kit For MP260AB 537021-6U-US 1
3Plate, Shim 1 537576-1-US 1
4Plate, Shim 2 537577-1-US 1
5Kit, MP260 Bushing (Optional) See Section Options 117362 1
6Assy, MP260 Additional Part Kit 537645-US 1
TDL-MP260-6
1
2
3
4
5
6

Overview
MP260 Additional Part Kit
Overview 12/9/21 2-2
2
2.2 MP260 Additional Part Kit
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
ASSY, MP260 ADDITIONAL PART KIT 537645-US
1Bar, Regulating bar 360-911 1
2Plate, Additional Plate MP260 537646-1-US 1
3Kit, MP Shims 117361 1
Washer 30/42-2 FE/ZN5 DIN 988 F81069-1 4
Washer 30/42-1 FE/ZN5 DIN 988 F81069-2 2
Washer 30/42-0.5 FE/ZN5 DIN 988 F81069-3 2
Washer 30/42-0.3 FE/ZN5 DIN 988 F81069-4 2
Washer 30/42-0.2 FE/ZN5 DIN 988 F81069-5 2
Washer 30/42-0.1 FE/ZN5 DIN 988 F81069-6 2
4Bushing, 1-5/8ODx1.183IDx1.583 535848-1-US 1
5Bushing, 1.181IDx1.249ODx1.566 537654-US 1
6MP160 Wrench Kit 535185-US 1
Wrench, 5mm Hex 092915-US 1
Wrench, 4mm Hex 093368-US 1
Wrench, 10mm Flat 535177-1-US 1
Wrench, 6mm Hex 535186-US 1
7Plate, Knife Alignment Tool 534770-US 1
8Wrench, 30mm Flat 537649-US 1
9Bracket, Cutter Guard 533502-US 1
10 Bracket, Cutter Guard 537648-US 1
TDL-MP260-05
1
2
3
4
5
67
8
9
10

Mechanical Assembly
Covers
3-1 12/9/21 Mechanical Assembly
3
SECTION 3 MECHANICAL ASSEMBLY
3.1 Covers
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
1Grommet, Rubber 087065 2
2Grommet, Rubber 3/8 ID 025248 1
3Front Small Cover 537567-1-US 1
4Plate, Side 533096-1-US 2
5Washer, M6 Flat Class 4 F05026-1 12
6Screw, M6-1 x 20 SHC F05020-15 12
7Knife, Planer, 260upr/360lwr 410mm notch (Upper cutter, single knife) TPK410.20MP 2

Mechanical Assembly
Covers
Mechanical Assembly 12/9/21 3-2
3
3.2 Table MP260
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
- ASSEMBLY, MP260 MECHANICAL 537004-US 1
1Table MP260 260-512B 1
2Screw, M6-1.0x12mm HSFH, 10.9 Zinc F81001-54 4
3Right Spindle Assembly See Section 3.3 537135-US 1
4Pulley, 8PJx48mmx28mm 533586 2
5Screw, M8-1.0x12mm SHSS Cup Point F81002-105 2
6Bracket, Fence 537006-US 1
7Bracket, Fence2 537007-US 1
8Washer, M8 Flat F05026-4 5
9Washer, M8 Split Lock F05011-45 4
10 Bolt, M8x1.25x20mm SHCS F05005-150 4
11 Bracket, Table Plate 1 537563-1-US 1
12 Assy, Cutterhead; 72D x 300L mm; 4kn See Section 3.4 537568 1
13 Knife, Planer; HSS; 300mm (11.8") L w/ Notch TPK300.20MP 2
14 Fence 1, Assembly See Section 3.5 537570 1
15 Fence 2, Assembly See Section 3.5 537572 1
16 Slide Plate 1 537573-US 2
17 Slide Plate 2 537574-US 2
18 Bracket, Indicator, Scale 537559-1 1
19 Washer, M5 Flat SS PK/100 F05011-129 2
20 Screw, M8-1.25x16 SHC F05021-10 1
21 Indicator, Blade Width Scale 094821 1

Mechanical Assembly
Covers
3-3 12/9/21 Mechanical Assembly
3
22 Washer, M5 Flat SS PK/100 F05011-129 2
23 Screw, M5-0.8x16mm SHCS SS PK/50 F05004-259 2
24 Nut, M5-.8 Class 8 Hex Nylock F05027-3 2
25 Decal, Vertical Scale 533579-US 1
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.

Mechanical Assembly
Covers
Mechanical Assembly 12/9/21 3-4
3
3.3 Right Spindle Assembly
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
- RIGHT SPINDLE ASSEMBLY 537135-US 1
1Shaft, MP260 537134-US 1
2Bushing, 30/42-20.2 Zinc-plated 533541-1-US 2
3Bushing, 30/42-10 Zinc-plated 533539-1-US 2
4Bushing, 30/42-5.2 Zinc-plated 533540-1-US 1
5Bushing, 1-5/8xM20-1.5x25/32 535886-1 1
6Bearing, 6006 2rsr 096191 1
7Outside Retaining Ring Z30 Pn-m/85111 Din 471 F81090-23 2
8Bearing, 6206 2rsr P6 Rolling (Fag, Nsk, Skf) 100787 1
9Plate, Washer MP260 533543-US 1
10 Plate, Clamping 533542-1-US 1

Mechanical Assembly
Covers
3-5 12/9/21 Mechanical Assembly
3
11 Screw, M6-1.0 x 16mm SHCS F05004-206 2
12 Cutterhead, 88D x 40L x 30B mm; Side 2kn 240-010 1
13 Knives, Cutter (set of 2) TPK50.024.4TB 1
Wedge KIL-TB90-92S 1
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.

Mechanical Assembly
Covers
Mechanical Assembly 12/9/21 3-6
3
3.4 Bottom Cutterhead
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
- BOTTOM CUTTER - ASSEMBLY 537568 1
1Nut M6 Zc 8 Nylock Din 982 Iso 7040 F81031-2 2
2Washer 6,4 Zc Din 126 Iso 7091 F81053-1 2
3Bearing Housing 1 536958-1 2
4Washer 6,5 Zc Fender Din 9021 Iso 7093 F81053-11 2
5Bolt M6x25 Hh Zc Ft 8.8 Din 933 F81001-3 2
6O-ring 536959 2
7Bearing, 6006 2rsr 096191 2
8Lower Cuttting Head MP260 260-140-5 1
9Screw M6x12 Lshcs 10.9 Din 7984 F81001-80 4
10 Washer 8,2 Zc Spring Lock Din 127 F81054-4 4
11 Screw M8x60 Lhscs 8.8 Din 7984 F81002-41 4
12 Wedges, 11.8" (300mm) - 2 PCS 241-061 1
13 Bolt M6x12 10.9 Din 933 Iso 4017 083595 10
14 Knife, Planer; HSS; 300mm (11.8") L w/ Notch (Bottom cutter, individual knife) TPK300.20MP 2
TDL-MP260-21
123456789
10
11
12
13
14

Mechanical Assembly
Covers
3-7 12/9/21 Mechanical Assembly
3
3.5 Infeed and Outfeed Fences
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
Assy, Infeed Fence 537570 1
Assy, Outfeed Fence 537572 1
1Fence 1, Infeed 537569-1 1
Fence 2, Outfeed 537571-1 1
2Clamp 536966-1 2
Adjustable Knob 536965 2
3Pin Guide 537001-1 1
4Knob Pin 536999-1 1
5Insert 537002 1
6Washer 8,4 Zc Din 126 Iso 7091 F81054-1 1
7Bolt M8x20 Hh Zc Ft 8.8 Din 933 F81002-4 1
8Thread Pin M6 541455 1
9Knurled Nut 541454 1
10 Nut M6 Zc 8 Nylock Din 982 Iso 7040 F81031-2 2
11 Washer 8,2 Zc Spring Lock Din 127 F81054-4 4
12 Screw M8x40 Shcs Zc 8.8 Din 912 Iso 4762 F81002-29 2
13 Screw M8x20 Shcs Zc 8.8 Din 912 Iso 4762 F81002-30 2

Mechanical Assembly
Covers
Mechanical Assembly 12/9/21 3-8
3
3.6 Feed Assembly
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
- FEED ASSEMBLY 536997-US 1
1Drive Shaft Assembly See Section 3.7 533580 2
2Drive Shaft Assembly See Section 3.7 537585 2
3Shaft Assembly, W/protective Cover See Section 3.7 533581 1
4Assy, Sprocket, #35, 27T 533109-US 7
5Plate, 2-1/8x3-5/8x1/16 536998-1-US 3
6Tension Plate Complete See Section 3.9 537535-US 1
7Screw, M8-1.25x20mm SHSS Dog Point F81002-77 8
8Assy, Sprocket, #35, 21T 117344 1
9Chain, #35x56 Pitches Incl/Master Link 537052-US 1
Link, #35 Master 032170 1
10 Chain, #35x78 Pitches Incl/Master Link 537053-US 1
Link, #35 Master 032170 1
11 Chain, #35x70 Pitches Incl/Master Link 537054-US 1
Link, #35 Master 032170 1
12 Chain, #35x54 Pitches Incl/Master Link 537051-US 1
Link, #35 Master 032170 1

Mechanical Assembly
Covers
3-9 12/9/21 Mechanical Assembly
3
3.7 Drive Shaft Assemblies
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
- DRIVE SHAFT ASSEMBLY 533580 1
- DRIVE SHAFT ASSEMBLY 537585 1
- DRIVE SHAFT ASSEMBLY 533581 1
1Shaft, Steel Drive for 533580 533513-1 1
Shaft, Steel Drive for 533585 537586-1 1
Shaft W/protective Cover for 533581 533512 1
2Bearing Assembly, Slide See Section 3.8 533520 2

Mechanical Assembly
Covers
Mechanical Assembly 12/9/21 3-10
3
3.8 Slide Bearing Assembly
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
- BEARING ASSEMBLY, SLIDE 533520 1
1Housing, Slide Bearing 533514 1
2Slide Block Assembly 537575 1
3Rod, M8 Threaded 533518 1
4Cover, Rubber 533516 1
5Spring 533519 1
6Washer 8,4 Zc Din 126 Iso 7091 F81054-1 1
7Nut M8 Zc 8 Nylock Din 982 Iso 7040 F81032-2 1
8Screw M4x12 Phillips Zc 5.8 Din 7985 F81011-43 2
9Bolt M6x40 HH Zc Ft 8.8 Din 933 F81001-5 2
10 Washer 6,4 Zc Din 126 Iso 7091 F81053-1 2
11 Nut M6 Zc 8 Nylock Din 982 Iso 7040 F81031-2 2

Mechanical Assembly
Covers
3-11 12/9/21 Mechanical Assembly
3
3.9 Tension Plate
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
- TENSION PLATE COMPLETE 537535-US 1
1Bracket, Tension Plate 537534-1-US 1
2Bushing, Spacer R80671-6-US 1
3Bolt, M6-1.0x35mm Class8 HH F05020-9 1
4Washer, M6 Flat Class 4 F05026-1 4
5Nut, M6-1 Swaged F05027-16 2
6Screw, M6-1.0 x 16mm SHCS F05004-206 2

Mechanical Assembly
Covers
Mechanical Assembly 12/9/21 3-12
3
3.10 Cutterhead Assembly (Upper)
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
- SHAFT ASSEMBLY, DRIVE 533682 1
1Housing Assembly, Bearing See Section 3.11 533593 2
2Bearing, 6206 2rsr P6 Rolling (Fag, Nsk, Skf) 100787 2
3Shaft, Main 260-138 1
4Screw M6x12 Lshcs 10.9 Din 7984 F81001-80 4
5Wedges, 410mm 16" - 2 PCS 241-060 1
6Bolt M6x12 10.9 Din 933 Iso 4017 083595 14
7Knife, Planer; HSS; 410mm (16") L w/ Notch TPK410.20MP 2
TDL-MP260-20
1
2
3
4
5
6
7

Mechanical Assembly
Covers
3-13 12/9/21 Mechanical Assembly
3
3.11 Bearing Housing
REF DESCRIPTION (♦ Indicates Parts Available in Assemblies Only) PART # QTY.
- HOUSING ASSEMBLY, BEARING 533593 1
1Housing, Bearing 533590-1 1
2O-ring, Bearing Housing 533592 2
3Washer 6,4 Zc Din 7349 F81053-13 2
4Bolt M6x35 Hh Zc 8.8 Pt Din 931 F81001-71 1
5Nut M6 Zc 8 Nylock Din 982 Iso 7040 F81031-2 1
6Washer 8,4 Zc Din 126 Iso 7091 F81054-1 8
7Screw M8x40 Shcs Zc 8.8 Din 912 Iso 4762 F81002-29 4
8Nut M8 Zc 8 Nylock Din 982 Iso 7040 F81032-2 4