Woodway Desmo Firmware update

WOODWAY 4FRONT, DESMO.
PATH, AND MERCURY TREADMILL
ASSEMBLY DIRECTIONS
"Woodway Treadmill Assembly Directions - ATTACHED
Top arm assembly + 2 side plastics (4 pieces total)"

44 03/2016 –UM-MT-EN-01
6.4 Assembly Instructions
6.4.1 Preparation
The treadmill can be delivered in various states of assembly. Disassembly/assembly may
be required for moves or relocation into other rooms.
NOTE
In WOODWAY performance and fitness treadmills, standard (inch) screws and
nuts are used, with few exceptions.
These are not compatible with metric fastening elements!
Due to the heavy weight of the device, it is recommended to install the treadmill as close
to its final location as possible.
Carefully dismantle the shipping crate. To do this, remove the screwed connections. Re-
move protective foil from all packaged parts. Ensure that the surfaces are not damaged
by sharp objects (knife, etc.).
NOTE
It is recommended to have a second person assist in inserting the railing
tubes or with the assembly.
6.4.2 4Front
Tools required for assembly:
1x combination wrench or ratchet wrench, ½”
1x Phillips head screwdriver, #2
1. Remove the covers on the
left and right.
Fig. 15 4Front assembly, side panel
Preparation Steps

03/2016 –UM-MT-EN-01 45
2. Insert wire and protective
cover into the handrail tube
to prevent damage during
insertion.
Fig. 16 4Front assembly, wiring
3. Prepare the mount for the
tube.
Fig. 17 4Front assembly, tube mount
4. Insert the handrail tube into
the mounts.
Note: Do not damage the
wires!
Be careful not to pinch
yourself!
Fig. 18 4Front assembly, inserting tubes

46 03/2016 –UM-MT-EN-01
5. Pull the wire and protective
cover out of the handrail
tube.
Fig. 19 4Front assembly, connection 1
6. Lay the wire with protective
cover behind the handrail
mount.
Fig. 20 4Front assembly, connection 2
7. Insert the Display plug and
tighten both retaining
screws.
8. Attach the protective con-
ductor (green) to the con-
tact tab on the frame.
9. Connect any other connec-
tions to the interface panel
Fig. 21 4Front assembly, connection 3

03/2016 –UM-MT-EN-01 47
10. Tighten handrail clamp
bolts.
Fig. 22 4Front assembly, securing the railing
11. Replace the right and left
side panels and secure
them with screws.
12. Insert all screws by hand
first, then tighten them
down completely
Fig. 23 4Front assembly, side panel

48 03/2016 –UM-MT-EN-01
6.4.3 Desmo
Tools required for assembly:
1x combination wrench or ratchet wrench, ½”
1x Phillips head screwdriver, #2
1. Remove the covers on the
left and right.
Fig. 24 Desmo assembly, removing side covers
2. Insert wire and protective
cover into the handrail tube
to prevent damage during
insertion.
Fig. 25 Desmo assembly, wiring
3. Prepare the mount for the
tube.
Fig. 26 Desmo assembly, tube mount

03/2016 –UM-MT-EN-01 49
4. Insert the handrail tube in-
to the mounts on both
sides.
Note: Do not damage the
wires! Be careful not to
pinch yourself!
Fig. 27 Desmo assembly, inserting tubes
5. Tighten the handrail mount
bolts on both sides.
Fig. 28 Desmo assembly, fixing the railing
6. Remove electronic cover
plate on the right side of
the treadmill frame using a
Phillips screw driver.
Fig. 29 Desmo assembly, electronic cover plate

50 03/2016 –UM-MT-EN-01
7. Lay the wire through the
hole in the console.
Fig. 30 Desmo assembly, connection 1
8. Attach the protective con-
ductor (green) to the con-
tact tab on the housing.
Fig. 31 Desmo assembly, connection 2
9. Connect the display cable
to the circuit board. The
connector is J10.
Note: Do not connect dis-
play cable to the position
marked with the red “X” in
Fig. 29!
Fig. 32 Desmo assembly, connection 3

03/2016 –UM-MT-EN-01 51
10. Connect the wires to the
frame with the supplied
wire ties.
11. Connect and secure all oth-
er connections from hand-
rail.
Fig. 33 Desmo assembly, connection 4
12. Reinstall electronic cover
plate on the right side of
the treadmill frame using a
Phillips screw driver.
Fig. 34 Desmo assembly, electronic cover plate
13. Slide the side covers onto
the left and right sides.
14. Guide the covers, slightly
tilted under the handrail
boots.
15. Attach the side covers and
railing covers with screws
(do not tighten the screws
yet).
Fig. 35 Desmo assembly, side covers

52 03/2016 –UM-MT-EN-01
16. Position the side covers so
that a ¼ in. (5 mm) gap is
visible.
17. Then tighten all screws.
Note: The side covers
must not be in contact with
the running surface or drive
belts on the rear left side!
Fig. 36 Desmo assembly, adjusting side covers
6.4.4 ELG
Please contact your local representative for ELG assembly assistance.
6.4.5 Mercury, Path
Tools required for assembly:
1x combination wrench or ratchet wrench, ½”
1x Phillips head screwdriver, #2
1. Remove the cover plates
and side covers on both
sides.
Fig. 37 Mercury/Path assembly, side covers
2. Insert wire and protective
cover into the guard rail
tube to prevent damage
during insertion.
Fig. 38 Mercury/Path assembly, wiring