Woosim Systems WSP-i350 User manual

http://www.woosim.com
MODEL WSP-i350
(3inch Rugged Mobile Printer)
Rev. 4.1
WOOSIM SYSTEMS Inc.
(#501, Daerung Technotown 3th)
115, Gasan digital 2-ro, Geumcheon-gu,
Seoul, 153-772 Rep. of KOREA
Tel : [phone]
Fax : [phone]
URL: http://www.woosim.com
All specifications are subjected to change without notice

WSP-i350 Rev. 4.1
http://www.woosim.com
2
 Copyright
WSP-i350 3inch Rugged Mobile printer operator’s manual.
Copyright ⓒ2016 by Woosim Systems Inc.
All rights reserved.
The information contained in this manual is the property of Woosim Systems Inc.
And may not be reproduced in whole or in part without the prior written permission
of Woosim Systems Inc.
 Trademark
a registered trademark of Woosim Systems Inc.
All other trademark are the properties of their respective companies.
 Caution
Some semiconductor devices are easily damaged by static electricity. You should
turn the printer “OFF”, before you connect or removed the cable on the rear side, in
order to guard the printer against the static electricity.
If the printer is damaged by the static electricity, you should turn the printer “OFF”
 Notice
The contents of this manual are subject to change without notice.

WSP-i350 Rev. 4.1
http://www.woosim.com
3
 Introduction
The WSP-i350 is the ideal solution for Mobile banking system , Retail,
point of sales, Credit card Transaction, other traveling and mobile
computing etc.
The general features of WSP-i350 printer are as follows:
Compact size (120×130.5×58.4mm)
Light weight(395g) for true mobility [standard]
Very silent printing thru direct thermal printing method
High speed (120mm/sec, MAX)
High resolution(203dpi : 8dots/mm).
UART, Bluetooth Ver3.0,
Wireless LAN(IEEE802.11b/g/n)[option] interface
Support Magnetic Stripe Reader[option]
Support Graphic LCD(128×32dots) with Blue LED Backlight
Support text and graphic printing
Intuitive LED’s indicate Power(on/off), Error
Easier paper roll loading by CLAMSHELL design
One touch paper cover
Printer door open & Paper-out sensor
Easier maintenance with self-diagnostic.
In field programming –Update Firmware, Download Fonts and Logos
Water-resistant construction.( IP54 –Certified )
Microsoft Windows XP/VISTA/7/8/CE, Linux, Android compatible.
Flow control : Software (XON/XOFF)
※Hardware flow control not supported in printer.
Free fall: 1.5 meter
Agency Approvals

WSP-i350 Rev. 4.1
http://www.woosim.com
4
 Operating Precautions
Please follow the precautions below to enjoy and maintain the full performance
of the printer.
Using the Printer
● Be careful not to drop or bump the printer on a hard surface.
● Do not install the printer in direct sunlight or such areas.
Suitable environment for the use of the printer is as follows:
◆ Operating temperature :-10°C to 50°C
◆ Relative humidity : 30% to 80%
● Do not install the printer near devices that generate strong
electromagnetic fields such as a copy machine.
● Do not open the platen cover during printing .
● Do not remove or reinstall the communication cable during printing
or transmission.
● Do not touch the connectors of the communication during printing.
● Switch the POWER OFF when not in use.
● Do not use other solvent.
●The AC adapter, the battery charger and the battery pack may
become warm when in use. This is normal and is not a malfunction.
● When the battery pack is used at low temperature, the length of time
the printer can be used may be shortened.
Thermal Paper Handling
● Store the thermal paper in a cool, dry and dark place.
● Do not rub the paper with hard object.
● Do not leave the paper with hard object.
● Do not allow plastic film, erasers, or adhesive tape to touch the paper
for long periods.
● Do not stack the thermal paper with diazo copies immediately
after copying or wet-type copies.
● Do not use chemical glue.
●Always use the clean thermal paper.

WSP-i350 Rev. 4.1
http://www.woosim.com
5
Federal Communications Commission
Radio Frequency Interference Statement
FCC ID : QDDWSP-I350X
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
ㆍReorient or relocate the receiving antenna.
ㆍIncrease the separation between the equipment and receiver.
ㆍConnect the equipment into an outlet on a circuit different from that to which the receiver
is
connected.
ㆍConsult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user's authority to
operated the equipment under FCC rules.
This Device has been evaluated to comply with RF exposure requirement for general use limit
in portable condition. It is safe to be used in sold condition.
CE WARNING
ㆍChanges and modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
ㆍIt is desirable that it be installed and operated with at least 20cm or more between the
radiator and person’s body(excluding extremities hand, wrists, feet, and ankles)

WSP-i350 Rev. 4.1
http://www.woosim.com
6
CONTENTS
1. Outline. .................................................................................................................................. 8
1.1. Model classifications................................................................................................... 8
1.2 Product Part Number System..................................................................................... 9
1.3. Specifications. ............................................................................................................ 10
2. Setting up the printer....................................................................................................... 12
2.1. Printer & Accessories................................................................................................ 12
2.2. Printer Features ......................................................................................................... 13
2.3. Dimensions................................................................................................................. 14
2.4. Replacing paper roll. ................................................................................................. 16
2.5. Power supply ............................................................................................................. 17
2.5.1. Specified power supply.................................................................................. 17
2.5.2. Installing the battery ...................................................................................... 17
2.5.3. Recharging the battery pack......................................................................... 18
2.6. Set operation mode.................................................................................................. 19
2.7. Confirmation of the Wireless-LAN information..................................................... 24
2.7.1. MAC Address printing.................................................................................... 24
2.7.2. Confirmation of the Wireless-LAN setting information ............................. 24
3. Interface............................................................................................................................... 25
3.1. UART(RS-232C or TTL) or USB................................................................................. 25
3.2. Bluetooth.................................................................................................................... 26
3.3. Wireless LAN.............................................................................................................. 26
3.4. Card Reading ............................................................................................................. 26
4. Using the printer................................................................................................................ 27
4.1. Control panel. ............................................................................................................ 27
4.2. The self test ............................................................................................................... 28
4.3. Using the Accessory ................................................................................................. 28
4.3.1. Using the Shoulder strap............................................................................... 28
4.3.2. Using the Belt clip .......................................................................................... 29
5. Consumable Parts.............................................................................................................. 30

WSP-i350 Rev. 4.1
http://www.woosim.com
7
5.1. Recommended paper................................................................................................ 30
5.2. Printing position. ....................................................................................................... 30
6. Revision History ...............................................오류! 책갈피가 정의되어 있지 않습니다.

WSP-i350 Rev. 4.1
http://www.woosim.com
8
1
1. . O Ou ut tl li in ne e. .
1
1. .1 1. . M Mo od de el l c cl la as ss si if fi ic ca at ti io on ns s. .
1
1. .2 2 S Sy ym mb bo ol l
WSP-i350 ( ) ( )
Model
Interface
A1 : UART/Bluetooth
(Standard)
Power
None : DC 8.4V
Standby symbol
IEC 5009, the standby symbol(line partially within a broken circle),
Indicates a sleep mode or low power state.
Direct current symbol
This symbol is found on many electronic devices that either require
or produce direct current.

WSP-i350 Rev. 4.1
http://www.woosim.com
9
1
1. .3 3 P Pr ro od du uc ct t P Pa ar rt t N Nu um mb be er r S Sy ys st te em m
Model name / Interface Spec.
Example) 1. Porti-S40 Serial/Bluetooth Part No. ⇒S40/A1
2. Porti-SC30 Bluetooth Only Part No. ⇒SC30/Z1
Note) The above table is the interface format which is supported.
But some of the interfaces are not supported according to the product
and please contact us, if you have any questions regarding the interface.
S40
SC30
W25
.
.
.
Wired
Wireless
A
RS-232C
1
Bluetooth
B
TTL
2
IrDA
C
USB
3
Wireless LAN
D
RS-485
0
None
E
Parallel
Z
None

WSP-i350 Rev. 4.1
http://www.woosim.com
10
1
1. .4 4. . S Sp pe ec ci if fi ic ca at ti io on ns s. .
Item
Specifications
Print method
Direct thermal line printing
Character size
- Font Size A: 12X24 / Font Size B : 9X24 / Font Size C : 8X16
- KOR : 24X24(16X24) / CHN, JPN : 24X24
Characters per line
- Font A : 48cpl / Font B : 64cpl / Font C : 72cpl
- KOR, CHN, JPN : 24cpl
Optional Characters
Alphanumeric:95, Extended Graphics:128X50 pages, International:10,
Simplified/Traditional Chinese, Japanese, Korean(optional)
Resolution
203dpi, 8dots/mm
Print width
3-inch (72mm, 576dots)
Print speed
120mm / sec (MAX)
Dimension
120×130.5×58.4mm
120×132.5×58.4mm (MSR model)
Weight
(Including battery)
395g / 407g (MSR model)
Interface
UART, Bluetooth Ver 3.0,
Wireless LAN(IEEE802.11b/g/n) [option]
Paper roll
Thermal roll paper (80mm wide, 50ø)
Barcodes
1-dimension : UPC-A, UPC-E, EAN-8, EAN-13, CODE-39, CODE-93,
CODE-128, ITF, CODABAR
2-dimension : PDF417, Micro PDF417, Truncated PDF417, QR-CODE,
DATA Matrix, Maxicode
Etc :GS1 databar
Driver
Microsoft Windows XP/VISTA/7/8/CE, Linux, Android compatible.
H/W Spec
MCU : RX-32bit, RAM : 128M bit, FLASH : 64M bit
Receive buffer size
1M bytes
Sensor
Support Cover open, Paper, Label
( Continue…)

WSP-i350 Rev. 4.1
http://www.woosim.com
11
Item
Specifications
MSR [option]
1&2 or 2&3 Track Reading
LCD
128×32 Dots FSTN (Blue LED Backlight)
Battery
Rechargeable 7.4V DC, 1,800mAh /2200mAh (Li-ion)
Battery duration
1 hour continuous printing
Battery charger
Input (100~250V AC, 50~60Hz)
Output(8.4VDC/0.8A), 4hours full charge time
Environment
conditions
Temperature
-10°C ~ 50°C (operating)
-10°C ~ 70°C (storage)
Humidity
30% - 80% (operating)
10% - 90% (storage)
MCBF(Mean Cycle
Between Failure)
Mechanical
37,000,000 lines
Head
Approximately 50Km
< Table 1 >

WSP-i350 Rev. 4.1
http://www.woosim.com
12
2
2. . S Se et tt ti in ng g u up p t th he e p pr ri in nt te er r. .
2
2. .1 1. . P Pr ri in nt te er r & & A Ac cc ce es ss so or ri ie es s
Your printer box should include these items. If any items are damaged or
missing, please contact your dealer for assistance.
WSP-i350
Battery Pack
▼ OPTIONAL
Communication cable
Shoulder strap
MSR
Thermal roll paper
Battery charger adaptor
Belt clip

WSP-i350 Rev. 4.1
http://www.woosim.com
13
2
2. .2 2. . P Pr ri in nt te er r F Fe ea at tu ur re es s
MSR model
Standard model

WSP-i350 Rev. 4.1
http://www.woosim.com
14
2
2. .3 3. . D Di im me en ns si io on ns s
▶Standard model
120
130.5
58.4

WSP-i350 Rev. 4.1
http://www.woosim.com
15
▶MSR model
120
132.5
58.4

WSP-i350 Rev. 4.1
http://www.woosim.com
16
2
2. .4 4. . R Re ep pl la ac ci in ng g p pa ap pe er r r ro ol ll l. .
1. Make sure that the printer is not receiving data; otherwise, data may be lost.
2. Open the paper cover as the “One-Touch” way by pressing the button in the arrow
direction like the picture.
3. Insert a new paper roll as shown.
4. Tear the excess paper off using the edge of paper door as a tear bar.
Note : Be sure to use paper rolls that meet the specifications.
Do not use paper rolls that have the paper glued to the core because the
printer can not detect the paper end correctly.

WSP-i350 Rev. 4.1
http://www.woosim.com
17
2
2. .5 5. . P Po ow we er r s su up pp pl ly y
2
2. .5 5. .1 1. . S Sp pe ec ci if fi ie ed d p po ow we er r s su up pp pl ly y
2
2. .5 5. .2 2. . I In ns st ta al ll li in ng g t th he e b ba at tt te er ry y
① To install battery pack, proceed as follows:
Insert the battery in the arrow direction and make sure the lock completed
② Reverse the order to remove the battery pack.
The following specification is requested for Power supply.
Battery Charger : DC 8.4V/0.8A
Avoid using power supply which its power capacity of power current is extremely high.
NOTE : ●Before installing or removing the battery pack, ensure the
printer is OFF.
● If the printer is not used for long period of time, remove the battery
pack from the printer.
● Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.

WSP-i350 Rev. 4.1
http://www.woosim.com
18
2
2. .5 5. .3 3. . R Re ec ch ha ar rg gi in ng g t th he e b ba at tt te er ry y p pa ac ck k
For recharging the battery pack, install the battery pack in the printer.
Insert the Battery Charger to the charge connector of the printer.
NOTE : ● While charging the printer, turn off the printer power.
● Do not remove the battery during charging.
●The battery is consumable parts and when purchasing, compared to
the use hour is gradually decreases. (Warranty 6 month)
● If the printer is not used for a long time, unplug the power cord
from the printer and outlet.
● The recharging time depends on the voltage level and ambient
temperature of the battery. Normally, if takes about 4 to 5 hours to
recharge a battery pack.
● You must use only the supplied adapter.
●Red Lamp : charging the battery.
Green Lamp: charging is finished.

WSP-i350 Rev. 4.1
http://www.woosim.com
19
2
2. .6 6. . S Se et t o op pe er ra at ti io on n m mo od de e
In keeping on pressing the Feed and Power button simultaneously until after the ERROR
lamp blinks 5 times, the printer comes out at the circumstance to change the printer mode.
(refer Table 2)
** If you want to change the Bluetooth Mode of printer, you need to disconnect the Bluetooth
function of the current paired Smartphone.
** Methods :
1. Turn off the Bluetooth function of the current paired Smartphone.
(Bluetooth ICON in LCD is disappeared.)
2. Change the printer mode.
(Additionally, we want to recommend you to rest(OFF→ON) the printer and change mode.)
Printer LCD status
Android status iOS status
*Note
No additional mode settings are required to connect Android or iOS devices.

WSP-i350 Rev. 4.1
http://www.woosim.com
20
FEED button : changing Printer MODE status. (Power Lamp)
POWER button : changing OPTION status. (Error Lamp)
[Example] The defaults of the printer are :
UART / 9600 bps / 8 data bit / No parity /1 stop bit / Density low /
Quality low / Mark use / Sensor High / 5 min Off
If a user wants to modify the defaults with
Bluetooth / 57,600 bps / 7 data bit / Odd parity /2 stop bit / Density high /
Quality high / Mark no use / Sensor Low / No use
Press FEED & POWER Button during the Error Lamp flickers 5 times.
You will see present COMMUNICATION mode in the LCD. (UART)
Press the POWER Button twice. And then, interface mode has set to
Bluetooth mode.
When you press FEED button once.
You will see present BAUD RATE mode in the LCD. (9600 bps)
Press POWER Button 3 times. And then, BAUD RATE has set to 57,600 bps.
When you press FEED button once.
You will see present DATA BIT mode in the LCD. (8 Data bit)
Press POWER Button once. And then Data Bit has set to 7 DATA BIT.
When you press FEED button once.
You will see present PARITY mode in the LCD. (No parity)
Press POWER Button once. And then the Parity bit has set to ODD Parity Bit..
When you press FEED button once.
You will see present STOP BIT mode in the LCD. (1 stop bit)
Press POWER Button once. And then the density has set to 2 Stop bit.
When you press FEED button once.
You will see present DENSITY mode in the LCD. (Density low)
Press POWER Button twice. And then the density has set to Density high.