WPG MTCL8FS10TDC User manual

KEEP FOR FUTURE REFERENCE
INSTRUCTIONS
International Version
MODEL NUMBER: MTCL8FS10TDC
SERIAL NUMBER: ___________
(please see serial label and record number here)
CLADDING LIFTER
DC-VOLTAGE
WITH DUAL VACUUM SYSTEM
AND VPFS10T PADS
READ ALL INSTRUCTIONS AND WARNINGS
BEFORE OPERATING THIS LIFTER
DESIGNED FOR THE MATERIALS HANDLING PROFESSIONAL
P.O. Box 368 – 908 West Main
Laurel, MT USA 59044
phone [phone]
phone [phone]
fax [phone]

View Quick Start Guide.

Rev 10.3/10-16 1 MTCL8FS10TDC: #35079
TABLE OF CONTENTS
SPECIFICATIONS............................................................................................................ 3
WARNINGS ..................................................................................................................... 4
OPERATING FEATURES................................................................................................... 5
ASSEMBLY....................................................................................................................... 7
TO SET UP THE LIFTER ................................................................................................................7
TO CHANGE THE PAD FRAME CONFIGURATION................................................................................8
To Install/Remove Pad Frame Extensions....................................................................................................10
To Install/Remove, Rotate and Position Pad Mounts.....................................................................................10
To Connect/Disconnect Vacuum Hoses........................................................................................................10
INTENDED USE .............................................................................................................11
LOAD CHARACTERISTICS...........................................................................................................11
OPERATING ENVIRONMENT .......................................................................................................12
DISPOSAL OF THE LIFTER ..........................................................................................................12
TYPICAL APPLICATIONS............................................................................................................13
OPERATION ..................................................................................................................11
BEFORE USING THE LIFTER........................................................................................................14
Taking Safety Precautions ..........................................................................................................................14
Performing Inspections and Tests...............................................................................................................14
Confirming the Pad Frame Configuration.....................................................................................................15
Preparing to Use the Optional Remote Control System.................................................................................15
TO APPLY THE PADS TO A LOAD..................................................................................................15
Powering up the Lifter................................................................................................................................15
Positioning the Lifter on the Load ...............................................................................................................16
Sealing the Pads against the Load...............................................................................................................17
Reading the Vacuum Gauges......................................................................................................................17
Vacuum Level on Optimal Surfaces .............................................................................................................18
Vacuum Level on Other Surfaces ................................................................................................................18
TO LIFT AND MOVE THE LOAD ....................................................................................................19
Positioning the Lift Bar...............................................................................................................................19
Interpreting the Warning Buzzer and Lift Light ............................................................................................19
Monitoring Vacuum Indicators ....................................................................................................................19
Controlling the Lifter and Load....................................................................................................................20
In Case of Power Failure ............................................................................................................................20
TO TILT THE LOAD ...................................................................................................................20
Tilting Loads When Lifter is Positioned Above Center ...................................................................................21
Tilting Loads When Lifter is Positioned On Center ........................................................................................21
Operating the Tilt Latches ..........................................................................................................................21
TO RELEASE THE PADS FROM THE LOAD .......................................................................................22
AFTER USING THE LIFTER..........................................................................................................23
Storing the Lifter........................................................................................................................................23

Rev 10.3/10-16 2 MTCL8FS10TDC: #35079
MAINTENANCE ............................................................................................................. 24
INSPECTION SCHEDULE.............................................................................................................24
Every-Lift Inspection ..................................................................................................................................24
Frequent Inspection...................................................................................................................................24
Periodic Inspection.....................................................................................................................................24
Infrequent Use...........................................................................................................................................25
TESTING SCHEDULE..................................................................................................................25
Operational Tests.......................................................................................................................................25
Load Test..................................................................................................................................................25
MAINTENANCE SCHEDULE..........................................................................................................26
BATTERY TEST.........................................................................................................................26
BATTERY RECHARGE.................................................................................................................27
VACUUM PAD MAINTENANCE......................................................................................................28
Friction Coefficient .....................................................................................................................................28
Inspection .................................................................................................................................................28
Cleaning....................................................................................................................................................28
Sealing Ring Replacement ..........................................................................................................................29
VACUUM TEST .........................................................................................................................29
Dual Vacuum Circuit Test ...........................................................................................................................30
REMOTE CONTROL SYSTEM TEST ................................................................................................30
TILT DAMPER ADJUSTMENT .......................................................................................................31
TILT LATCHES ADJUSTMENT.......................................................................................................31
AIR FILTER MAINTENANCE −LARGE ...........................................................................................32
Filter Function and Conditions Requiring Service ..........................................................................................32
Filter Service Procedures ............................................................................................................................32
VACUUM PUMP MAINTENANCE −DYNAFLO DV1032102...............................................................33
Replacing the Diaphragm ...........................................................................................................................33
Replacing the Gasket/Flap Valves................................................................................................................33
Replacing the Head Assembly.....................................................................................................................33
VACUUM SWITCH ADJUSTMENT ..................................................................................................34
Vacuum Switch Function ............................................................................................................................34
Adjustment Procedure................................................................................................................................34
REPLACEMENT PARTS LIST.......................................................................................... 36
LIMITED WARRANTY.................................................................................................... 37

Rev 10.3/10-16 3 MTCL8FS10TDC: #35079
SPECIFICATIONS
Model Number:
MTCL8FS10TDC
Description:
Designed for use with a crane or other hoisting equipment, the MTCL8FS10TDC lifter employs
vacuum to hold a load for
lifting, and it provides manual 90° tilt movements for load
manipulation.
Power Source:
12 volts DC, 8 amps
Battery Capacity:
35 amp-hours
Vacuum Pads:
Eight 10" [25 cm] nominal diameter (Model VPFS10T), standard rubber, spring
-mounted (¾"
[20 mm] trave
l), with #60 filter screen and replaceable sealing rings for applications on rough
or textured surfaces
Pad Spread:
1
(to outer edges)
Minimum
Maximum w/o Extensions
Maximum w/Extensions
Length:
23¾" [60 cm]
39½" [101 cm]
179½" [456 cm]
Width:
23¾" [60 cm]
39¾" [101 cm]
39¾" [101 cm]
Load Capacity:
1
(rated at 16" Hg [-54 kPa] on clean, smooth, nonporous flat surfaces
2
)
Per-Pad:
150 lbs [68 kg]
Maximum:
700 lbs [320 kg] with 6 vacuum pads in use
Lifter Weight:
253 lbs [115 kg]
With Extensions:
368 lbs [167 kg]
Tilt Capability:
Manual, 90°; Latch engages automatically when pad frame reaches vertical or horizontal
position (if desired)
Dual Vacuum System:
2 vacuum system circuits allow the lifter to mainta
in the vacuum level in one circuit even if an
unexpected vacuum loss occurs in the other one (eg, due to load breakage).
Vacuum Pumps:
2 diaphragm type, 1 SCFM [28 liters/minute] nominal airflow
Vacuum Reserve Tanks:
2 vacuum reservoirs help prevent imme
diate vacuum loss in case of power failure and extend
battery life by reducing pump cycles required to maintain vacuum.
Vacuum Gauges:
2 dial gauges indicate current vacuum level in positive inches of Hg and negative kPa.
Vacuum Lift Lights:
2 green ligh
ts are energized whenever vacuum level is sufficient for lifting maximum load
weight (higher than 16" Hg [-54 kPa]).
Low Vacuum Warning Buzzer:
Maximum Alarm Volume = 103 dBA at 2 ft [60 cm].
While the lifter is powered up, an audible
alarm warns the ope
rator whenever vacuum is not sufficient for lifting the maximum load
weight.
Options:
Available
with Model EO8RC - Remote Control System. This option features a radio transmitter
and receiver that can activate apply and release functions at distances up to 250 ft [76 m]. The
system uses a 310-320 MHz signal.
Operating Elevation:
Maximum = 6000 ft [1828 m]
Operating Temperatures:
32° to 104° F [0° to 40° C]
Service Life:
This lifter is designed to have a service life of at least 20,000 lifting cycles,
when used and
maintained as intended.
Vacuum inserts, filter elements and other wear-out items are
excluded; see MAINTENANCE and REPLACEMENT PARTS LIST for more information.
For the
D
ISPOSAL OF THE
L
IFTER
after its service life, see INTENDED USE.
ASME Standard BTH-1:
Design Category "B", Service Class "0" (see www.wpg.com for more information)
!!–CE–!! Note: This symbol appears in the INSTRUCTIONS manual only when requirements of a CE Standard are different from
requirements of other standards that also apply to this vacuum lifter. CE requirements are mandatory in geographical areas
where CE Standards apply, but may be optional in other locations.
1For a listing of Pad Spread and Maximum Load Capacity for all pad frame configurations, see the illustration under ASSEMBLY:
TO CHANGE THE PAD FRAME CONFIGURATION.
2Load Capacity is based on a friction coefficient of 1; see MAINTENANCE: VACUUM PAD MAINTENANCE: Friction Coefficient for
additional information.

Rev 10.3/10-16 4 MTCL8FS10TDC: #35079
WARNINGS
Powr-Grip is pleased to offer the most reliable vacuum lifters available.
Despite the high degree of security provided by this product, certain
precautions must be observed to protect the operator and others.
Always
wear personal protective equipment that is appropriate for the material being
handled. Follow trade association guidelines.
Always
operate the lifter under conditions approved for its design (see INTENDED USE:
OPERATING ENVIRONMENT).
Never
operate a lifter that is damaged, malfunctioning, or missing parts.
Never
operate a lifter if the sealing edge of any vacuum pad is cut or otherwise damaged.
Never
remove or obscure warning labels.
Never
operate a lifter if the Load Capacity or any warning appears to be missing or obscured.
Always
make certain the contact surfaces of the load and all vacuum pads are clean prior to
applying the pads (see MAINTENANCE: VACUUM PAD MAINTENANCE).
Never
exceed the Load Capacity or attempt to lift loads the lifter is not designed for (see
INTENDED USE: LOAD CHARACTERISTICS).
Never
attempt to lift cracked or broken glass with this lifter.
Always
position the vacuum pads correctly on the load prior to lifting (see OPERATION: TO APPLY
THE PADS TO A LOAD).
Never
lift a load when any vacuum indicator shows inadequate vacuum.
Never
touch the vacuum release controls during a lift. This may result in loss of vacuum and
release of the load.
Never
allow people to ride on the lifter or the load being lifted.
Never
lift a load higher than necessary or leave suspended loads unattended.
Never
lift a load over people.
Always
keep other personnel far enough away from the lifter to avoid injury in the event of an
unexpected load release.
Always
place the power control in the inactive position and, when possible, disconnect the
power source before opening any enclosure on the lifter. (Only applicable to powered lifters)
Always
remember that modifications to the lifter may compromise its safety. Wood’s Powr-Grip
cannot be responsible for the safety of a lifter that has been modified by the customer. For
consultation, contact Wood's Powr-Grip (see LIMITED WARRANTY).
If the lifter is equipped with a Remote Control System,
never
operate the lifter remotely unless
there is clear communication about intended actions (eg, releasing load) with all personnel
near the lift. In addition, the operator must visually verify the status of the lifter and load
prior to remote operations.

Rev 10.3/10-16 5 MTCL8FS10TDC: #35079
OPERATING FEATURES
Note: Components featured in the following instructions for assembling, operating or
maintaining the vacuum lifter are underlined on their first appearance in each section.
Standard MTCL8FS10TDC shown without pad frame extensions.
1 ADJUSTABLE LIFT POINT TUBE
9 ENCLOSURE LATCH
17 BATTERY GAUGE
24 POWER SYSTEM ENCLOSURE, with:
2 LIFT BAR
10 VACUM PAD
18 BATTERY TEST BUTTON
VACUUM PUMPS
3 TILT DAMPER
11
PAD MOUNT
19 POWER LIGHT
VACUUM SWITCHES
4 TILT CONTROL LEVER
12 CONTROL HANDLE
20 CHARGER CORD RECEPTACLE
BATTERY
5 PAD FRAME
13 QUICK CONNECTORS
21 POWER SWITCH
BATTERY CHARGER
6 LIFT BAIL
14 TILT LATCH
22 CIRCUIT BREAKER
25 MOVABLE CONTROL PENDANT, with:
7 VACUUM LIFT LIGHT
15 AIR FILTER
23 CONTROLS RECEPTACLE
26 ENABLE RELEASE BUTTON
8 LOW VAC
UUM WARNING BUZZER
16 VACUUM GAUGE
27 APPLY/RELEASE SWITCH
28 Socket for PAD FRAME EXTENSION

Rev 10.3/10-16 6 MTCL8FS10TDC: #35079
OPTIONAL REMOTE CONTROL SYSTEM
OPTIONAL RADIO TRANSMITTER
1 RADIO RECEIVER
2 RADIO TRANSMITTER
3 STROBE LIGHT
4 VACUUM LIFT LIGHT
5 ENABLE BUTTON
6 APPLY BUTTON
7 RELEASE BUTTON
1 TRANSMISSION INDICATOR LIGHT
2 TRANSMITTER POWER/ENABLE BUTTON
3 RELEASE BUTTONS
4 APPLY BUTTONS
5 EMERGENCY TRANSMITTER DISCONNECT

Rev 10.3/10-16 7 MTCL8FS10TDC: #35079
ASSEMBLY
TO SET UP THE LIFTER
1) Open the shipping container and remove all materials for restraining or protecting the vacuum
lifter during shipping. Save the container for use whenever the lifter is transported.
2) Position the adjustable lift point tube as follows: The location of the lift point can be adjusted
to obtain the optimal hang angle of the lifter and load. A different hang angle may be
desirable, depending on the angle needed to attach the lifter to the load, release the load or
manipulate the load during a lift.
First disengage the lifter’s tilt latches (see OPERATION: TO TILT THE LOAD: Operating the Tilt
Latches) and raise the lift bar to a vertical orientation.
Make sure the lift bar latches in
the vertical orientation before releasing the lift bar.
To adjust the lift point location, remove both retaining bolts and associated hardware, and
reposition the adjustable lift point tube as desired. Reinstall the retaining bolts and hardware,
making sure to secure them tightly in position as originally installed.
WARNING: Lift point must be adjusted so as to prevent interference between
adjustable lift point tube and load.
Note: If the load would extend higher than the lift point when lifted or tilted upright (see
OPERATION: TO TILT THE LOAD), the lift point must be adjusted to prevent interference
between the adjustable lift point tube and the load. Failure to do so may damage the lifter or
load, and may result in the release of the load.
3) Suspend the lifter from a crane as follows: Select hoisting equipment (crane and hoist, when
applicable) rated to carry the maximum load weight plus the lifter weight (see
SPECIFICATIONS: Maximum Load Capacity and Lifter Weight).
Note: Any application of the lifter must conform to all statutory or regulatory standards that
relate to the hoisting equipment when used in its geographical location (eg, relevant OSHA
standards in the USA).
WARNING: Hoisting equipment hook must be fitted with restraining latch to
prevent lift bail from slipping off under any circumstances.
Attach the hoisting equipment hook to the lift bail, and use the hoisting equipment to raise
the lifter out of the shipping container. Be careful to avoid damaging any vacuum pads.
Note: Some hoisting equipment hooks could interfere with an upright load that extends
beyond the lifter’s pad frame. If the load would contact the hook during lifter operation, the
operator must prevent this by attaching a sling (or other rigging that does not interfere with
the load) between the hook and the lift bail.
WARNING: Any sling used must be rated to carry maximum load weight plus
lifter weight.

Rev 10.3/10-16 8 MTCL8FS10TDC: #35079
4) To use the movable control pendant (instead of the optional Remote Control System), insert
the plug of its coiled cord into the controls receptacle on the power system enclosure. Then
secure the connector by tightening its threaded collar.
5) Assemble the pad frame in the configuration that will provide optimal support of the load
while lifting (see TO CHANGE THE PAD FRAME CONFIGURATION to follow).
6) Open the power system enclosure and connect the electrical connectors uniting the battery to
the battery charger and the vacuum generating system. Now the lifter is operational.
7) Perform Operational and Load Tests for the lifter as directed in MAINTENANCE: TESTING
SCHEDULE. If the lifter is equipped with a Remote Control System, also perform the REMOTE
CONTROL SYSTEM TEST (see MAINTENANCE).
TO CHANGE THE PAD FRAME CONFIGURATION
This lifter offers a variety of pad frame configurations to accommodate different load dimensions
and weights (see illustrations on following page). Configurations are created by positioning or
removing the pad mounts, and/or by installing or removing pad frame extensions. Always
arrange the vacuum pads in a symmetrical configuration, in both width and length dimensions.
CAUTION: Vacuum pads must be mounted on main pad frame at all times.
To prevent lifter damage and to provide adequate load support, 4 activated vacuum pads must
be mounted on the main pad frame, regardless of the configuration selected (see illustrations on
following page). It is especially important to observe this rule when pad frame extensions are
employed: The vacuum pads may not be located solely on the extensions, as such a
configuration would not provide adequate load support.
The lifter is equipped with a dual vacuum system, as indicated by color-coded vacuum hoses.
For maximum effectiveness, adjacent vacuum pads must be connected to separate circuits of the
vacuum system in an even distribution. Make sure that an equal number of pads is connected to
the green circuit and to the red circuit.
After changing the pad frame configuration, make sure all vacuum hoses are secure and routed
to avoid being pinched, snagged, abraded or otherwise damaged while the lifter is in operation.
Also be sure to verify that all pads are connected and functioning correctly.

Rev 10.3/10-16 9 MTCL8FS10TDC: #35079
Pad Spread and Maximum Load Capacity
(larger configurations shown with pad frame extensions)

Rev 10.3/10-16 10 MTCL8FS10TDC: #35079
To Install/Remove Pad Frame Extensions
1) Insert the end of a pad frame extension in one socket on the main pad frame, so that the
holes align for the cotterless hitch pin.
2) Secure the pad frame extension in the pad frame by pushing a cotterless hitch pin through
the holes until the retaining ball emerges on the far side of the pad frame socket.
3) Use the quick connectors to connect the vacuum hoses from the pad frame extensions to the
main pad frame as directed in the discussion to follow.
3) Repeat steps 1-3 to install the other pad frame extensions as required for the pad frame
configuration desired.
4) To remove the pad frame extensions, reverse this procedure. Store pad frame extensions in
a clean, dry location to protect them from environmental exposure.
To Install/Remove, Rotate and Position Pad Mounts
1) Position a pad mount on one arm of the pad frame. Note that each pad mount can also be
rotated 180° to allow for the best hose routing.
2) Align the holes for the cotterless hitch pin in the pad mount with the corresponding holes in
the pad frame.
3) Use the quick connector to connect the vacuum hose from the vacuum pad to the appropriate
circuit of the vacuum system as directed in the discussion to follow.
4) Repeat steps 1-3 to install and position each vacuum pad as required for the pad frame
configuration desired.
5) To remove the pad mounts, reverse this procedure. Store pad mounts in a clean, dry location
to protect them from environmental exposure.
To Connect/Disconnect Vacuum Hoses
The vacuum hose for each vacuum pad is connected to or
disconnected from the vacuum system by means of a quick
connector. To connect the vacuum hose, push the male and
female ends of the connector together until they lock. To
disconnect the vacuum hose, move the release ring on the
female end until the connector separates.
Note: For proper function of the dual vacuum system, make sure
that vacuum pads are connected to alternating circuits of the
vacuum system (red or green).
Note: Whenever a quick connector is disconnected, the corresponding vacuum pad does not
contribute to the load capacity, whether or not the pad is mounted on the pad frame.
QUICK CONNECTOR
1) FEMALE END
2) MALE END

Rev 10.3/10-16 11 MTCL8FS10TDC: #35079
INTENDED USE
LOAD CHARACTERISTICS
WARNING: This lifter is NOT intended for lifting hazardous materials,such as
explosives or radioactive substances.
The operator must verify that the lifter is intended to handle each load, in accordance with the
following requirements:
• The load must not exceed the maximum allowable weight specified under Load Capacity (see
SPECIFICATIONS).
• The load must be a single piece of nonporous or semiporous material with a flat and relatively
smooth contact surface. Flexible sealing rings are able to accommodate some surface relief,
provided contour changes are not too abrupt. To determine whether the load is too porous,
rough or contoured to seal adequately, perform the test under Vacuum Level on Other
Surfaces (see OPERATION: TO APPLY THE PADS TO A LOAD).
• The load's contact surface must be suitable for obtaining a friction coefficient of 1 with the
lifter's vacuum pads (see MAINTENANCE: VACUUM PAD MAINTENANCE: Friction Coefficient), as
verified by a friction test. If necessary, contact Wood's Powr-Grip for help in conducting a
friction test.
• In order to avoid damaging the vacuum pads, the load's surface temperature must not exceed
the allowable Operating Temperatures (see SPECIFICATIONS). However, if such an
application cannot be avoided, Wood's Powr-Grip does offer a heat-resistant rubber
compound and other solutions which may enable you to lift loads with higher surface
temperatures. Contact Wood’s Powr-Grip or an authorized dealer for more information.
• While the minimum length and width of the load are determined by the Pad Spread (see
SPECIFICATIONS), the maximum length and width are determined by the allowable
overhang, or the amount of load material that can extend sideways beyond the vacuum pads
without breaking or otherwise being damaged.
The allowable overhang depends on the kind of load material being lifted, the thickness of the
material, and the angle at which it is handled (if any). Since materials such as glass, stone or
sheet metal each have different physical properties, the allowable overhang must be
evaluated separately for each type of load. If necessary, contact Wood’s Powr-Grip or an
authorized dealer for help in determining the recommended overhang in a specific situation.
• 8" [20 cm] is the maximum allowable thickness of loads at the maximum weight (see
SPECIFICATIONS: Load Capacity). However, allowable thickness increases as load weight
decreases. If necessary, contact Wood’s Powr-Grip for help in determining the maximum
thickness permitted when handling any specific load.
Note: Vacuum pads can stain or deform load surfaces with light colors or soft coatings. The
operator should test such surfaces for detrimental effects before using the lifter on them.

Rev 10.3/10-16 12 MTCL8FS10TDC: #35079
OPERATING ENVIRONMENT
The operator must determine whether the lifter is intended to be used in each work environment,
in accordance with the following restrictions:
WARNING: Never use lifter in dangerous environments.
• This lifter is not intended for use in any environment that is inherently dangerous to the
operator or likely to compromise the lifter's ability to function. Environments containing
explosives, caustic chemicals and other dangerous substances must be avoided when using
the lifter.
• The lifter's work environment is limited by the Operating Elevation and Operating Temperatures
indicated in SPECIFICATIONS.
• Using the lifter in wet environments may require the operator to take special precautions:
Moisture on contact surfaces of the load or vacuum pads diminishes the lifter’s slip resistance,
thereby reducing the lifting capacity (see MAINTENANCE: VACUUM PAD MAINTENANCE: Friction
Coefficient).
WARNING: Moisture reduces slip resistance of vacuum pads.
Although the lifter's exterior surfaces can tolerate some exposure to water vapor, they are not
designed to be water-tight. Submerging the lifter or using it in rain may damage lifter
components; these and similar conditions must be avoided.
• If the lifter is equipped with a Remote Control System, the work environment must be suitable
for using it, as verified by the REMOTE CONTROL SYSTEM TEST (see MAINTENANCE).
DISPOSAL OF THE LIFTER
After the vacuum lifter has reached the end of its service life, you must dispose of the lifter in
compliance with all local codes and regulatory standards that are relevant for the geographical
region.
Note: This lifter is equipped with a battery, which may be subject to special disposal regulations.

Rev 10.3/10-16 13 MTCL8FS10TDC: #35079
TYPICAL APPLICATIONS
Though the lifter is designed with the flexibility to be used in many different ways, these
illustrations represent some typical applications.

Rev 10.3/10-16 14 MTCL8FS10TDC: #35079
OPERATION
BEFORE USING THE LIFTER
The operator must determine whether the lifter is capable of performing each intended task, in
accordance with the SPECIFICATIONS and INTENDED USE sections of this INSTRUCTIONS
manual. In addition, all of the following preparations must be completed prior to lifting any load.
Taking Safety Precautions
The operator must be trained in all relevant industry and regulatory standards for the operation
of the vacuum lifter in its geographical location (eg, ASME B30.20 in the USA).
The operator must read and understand this INSTRUCTIONS manual, including all
WARNINGS
,
before using the lifter. If necessary, contact Wood’s Powr-Grip or an authorized dealer for
assistance.
WARNING: Always wear appropriate personal protective equipment.
The operator must wear any personal protective equipment and take any other precautions
required to handle the load safely. Consult appropriate trade association guidelines to determine
what precautions are necessary for each type of load material.
Performing Inspections and Tests
WARNING: Always check battery energy before using lifter.
(See MAINTENANCE: BATTERY TEST)
Perform all inspections and tests required by the INSPECTION and TESTING
SCHEDULES (see MAINTENANCE). In addition, if the lifter has been in storage,
always conduct a VACUUM TEST before placing it in service (see MAINTENANCE).
WARNING: Make sure alarm is clearly audible over ambient noise at operator
position.
The volume of the alarm may be adjusted by rotating the shutter of the low vacuum warning
buzzer. Make sure the alarm is loud enough to be heard over any other noise that may be
present while the lifter is in use. In addition, the alarm must be clearly audible at the maximum
distance the operator may be from the lifter, as well as through any barriers or obstructions
between the operator and the lifter. In order to be considered clearly audible,
the alarm
volume must exceed ambient noise by at least 15 dBA at the operator position.
3Since
the Maximum Alarm Volume is 103 dBA, ambient noise must not exceed 88 dBA under any
circumstances. Furthermore, if ambient noise measures 88 dBA, the alarm volume must be set
to maximum and the operator must remain within 2 ft [60 cm] of the warning buzzer, in order for
it to be effective.
3Consult CE Standard EN 457 for alternative ways to determine whether the alarm is clearly audible to operators.

Rev 10.3/10-16 15 MTCL8FS10TDC: #35079
CAUTION: Examine each air filter regularly,and empty when necessary.
Two air filters help protect the vacuum generating system from contaminants. However, the
lifter is not intended for use on wet load surfaces because the filters would not necessarily
prevent liquid from entering the vacuum system. In order for a filter to function, the operator
must empty the filter bowl before enough liquid accumulates to contact any portion of the filter
element (see MAINTENANCE: AIR FILTER MAINTENANCE).
Confirming the Pad Frame Configuration
WARNING: Load Capacity of lifter varies,depending on pad frame configuration.
Make sure the pad frame has been assembled in the configuration that will provide optimal
support of the load while lifting (see ASSEMBLY: TO CHANGE THE PAD FRAME CONFIGURATION). The
pad frame configuration selected must be appropriate both for the weight and for the dimensions
of the load to be lifted.
Preparing to Use the Optional Remote Control System
If the lifter is equipped with a Remote Control System, the operator can engage the lifter's apply
and release functions at distances up to 250 ft [76 m], provided there is a direct and clear view
of the lifter and its status indicators from the operator location (see MAINTENANCE: REMOTE
CONTROL SYSTEM TEST). When lifting a load from a remote location, the operator must monitor the
lifter at all times to make sure that it is functioning as intended.4In addition, the operator must
exercise special care to ensure that the load is landed and supported correctly before releasing
the load (see TO RELEASE THE PADS FROM THE LOAD to follow).
The radio transmitter is also equipped with an emergency transmitter disconnect that prevents
the transmitter from sending any transmission. This button should not need to be used, but may
have to be reset if accidentally engaged. To reset, twist the button clockwise while allowing it to
spring outward to its normal position.
TO APPLY THE PADS TO A LOAD
Powering up the Lifter
Place the lifter's power switch in the “on” ( ) position.5The blue power light remains
illuminated while the lifter is powered up. Keep the power switch in the “on” position while lifting
a load. Any power interruption during a lift could result in the release of a load and possible
injury to the operator or others (see TO LIFT AND MOVE THE LOAD: In Case of Power Failure to
follow).
WARNING: Never turn power off while lifting.
4The Remote Control System is designed with safeguards to prevent multiple lifters from responding until a clear transmission is
received. Nevertheless, radio controlled lifters should be tested to ensure that each transmitter controls only one lifter. The
buttons located on the lifter function regardless of any radio transmissions in the vicinity.
5When the operator powers up the lifter, either the stand-by function or the apply function is automatically activated, depending
on which was used last. If a vacuum pump or any other powered component fails to function while the lifter's power switch is in
the “on” position, examine each circuit breaker (adjacent to power switch) to determine whether it has interrupted the electrical
circuit to the component. Although the operator can reset the circuit breaker, the power interruption may indicate an electrical
problem that requires attention. Correct any deficiency before resuming normal operation of the lifter (see wiring diagram
provided).

Rev 10.3/10-16 16 MTCL8FS10TDC: #35079
If the lifter is equipped with a Remote Control System, press the transmitter power/enable button
and hold it briefly to activate the radio transmitter.6This button is also used to activate the
enable function (see TO RELEASE THE PADS FROM THE LOAD to follow).
Note: If the transmitter is activated, the transmission indicator light flashes green when any
button on the transmitter is pressed and held; if the transmitter is not activated, the indicator
light flashes red (see BEFORE USING THE LIFTER: Preparing to Use the Optional Remote Control
System preceding).
Positioning the Lifter on the Load
Make certain that the contact surfaces of the load and all vacuum pads are free of any
contaminates that could prevent the pads from sealing against the load (see MAINTENANCE:
VACUUM PAD MAINTENANCE).
To lift loads in the flat orientation (see INTENDED USE: TYPICAL APPLICATIONS), center the pad
frame to within 2" [5 cm] of the load center (hereafter, "on center"), since off-center loading can
cause the load to hang at an angle or to tilt unexpectedly (see TO TILT THE LOAD to follow), and it
may also damage the lifter.7
To lift loads in the upright orientation (see INTENDED USE: TYPICAL APPLICATIONS), center the pad
frame from left to right on the load and determine which will be the top edge of the load while
lifting. Then position the vacuum pads near that edge (hereafter, "above center"). This position
will maximize stability while lifting the load.
WARNING: When lifter is positioned above center, tilt latches must be locked
out before lifting load.
If the lifter is positioned above center on a load encountered in the flat orientation, the load
automatically tilts to the upright position when lifted (see TO TILT THE LOAD: Tilting Loads
Positioned Above Center to follow). In this case, failure to lock out the tilt latches could result in
an unexpected load release or damage to the lifter.
Make sure that all vacuum pads will fit entirely on the load’s contact surface (see
SPECIFICATIONS: Pad Spread) and that they will be loaded evenly while lifting (see
SPECIFICATIONS: Per-Pad Load Capacity). Then apply the lifter to the load so that all pads are
touching the contact surface.
WARNING: Lift point must be adjusted so as to prevent interference between
adjustable lift point tube and load.
Note: If the load would extend higher than the lift point when lifted or tilted upright, the lift
point must be adjusted to prevent interference between the adjustable lift point tube and the
load (see ASSEMBLY: TO SET UP THE LIFTER). Failure to do so could damage the lifter or load, and
may result in an unexpected load release.
6The radio transmitter turns off automatically, after a period of inactivity. The operator can also operate the lifter without using
the transmitter, if desired.
7The lifter is designed to handle the maximum load weight (see SPECIFICATIONS: Maximum Load Capacity) when the load’s
center of gravity is positioned within 2" [5 cm] of the pad frame’s center point. Occasional loading deviations are permissible,
provided that the operator can maintain control of the load at all times and that the load weight is low enough to avoid damaging
the lifter.

Rev 10.3/10-16 17 MTCL8FS10TDC: #35079
Sealing the Pads against the Load
The apply/release switch is located on the movable control pendant. The movable control
pendant allows the vacuum controls to be moved away from the lifter, so that the operator can
control airflow at a distance equal to the length of the pendant cord.
WARNING: Do not disconnect control pendant during lifter operation.
The movable control pendant is not intended to be disconnected during lifter operation.
Disconnecting the control pendant is likely to result in a load release and injury to the operator or
others nearby.
Turn the apply/release switch to the “apply” ( ) position (clockwise) to make sure the apply
function is activated.
WARNING: Keep apply/release switch in “APPLY” position throughout lift.
Alternatively, if the lifter is equipped with a Remote Control System, press an apply button on
either the radio transmitter or the lifter, to make sure the apply function is activated.
This energizes the vacuum pumps, causing air to be drawn immediately at the vacuum pads.
The low vacuum warning buzzer also sounds an alarm until the lifter attains sufficient vacuum to
lift the maximum load weight (see TO LIFT AND MOVE THE LOAD: Load Capacity and Lift Light to
follow). Press the lifter onto the load until all the pads seal against it. The apply/release switch
must remain in the “apply” ( ) position throughout the entire lift.
Note: If a vacuum pad has been lying against a hard object (as during shipping), it may be
slightly distorted. Although initially it may be difficult to apply the pad to a load, this condition
should correct itself with continued use.
Reading the Vacuum Gauges
The lifter is equipped with 2 vacuum gauges, which indicate the current vacuum level in each
circuit of the lifter's vacuum system. The green range indicates vacuum levels sufficient for
lifting the maximum load weight, whereas the red range indicates vacuum levels that are
not
sufficient for lifting the maximum load weight. The gauge needles should show a sudden surge
in vacuum as the vacuum pads seal against the load. If it takes more than 5 seconds for the
vacuum level to reach 5" Hg [-17 kPa] on a vacuum gauge, press on any pad that has not yet
sealed.

Rev 10.3/10-16 18 MTCL8FS10TDC: #35079
Vacuum Level on Optimal Surfaces
When the lifter is attached to clean, smooth, nonporous load surfaces, it should be able to
maintain a vacuum level in the green range on both vacuum gauges, except when used at high
elevations (see SPECIFICATIONS: Operating Elevation). If not, make sure the vacuum switches
are adjusted correctly (see MAINTENANCE: VACUUM SWITCH ADJUSTMENT). If the vacuum switches
cannot be adjusted to maintain a vacuum of 16" Hg [-54 kPa], perform the VACUUM TEST (see
MAINTENANCE) to determine whether there is a deficiency in the vacuum generating system.
Vacuum Level on Other Surfaces
When the lifter is attached to contaminated, rough or porous load surfaces, it may not be able to
maintain a vacuum level in the green range on both vacuum gauges, due to leakage in the seal
between the vacuum pads and the load surface.8In the case of contamination, thoroughly clean
the contact surfaces of the load and the vacuum pads (see MAINTENANCE: VACUUM PAD
MAINTENANCE: Cleaning), and reapply the lifter to the load. If the load has rough or porous
surfaces,
the operator must conduct a test to determine whether the lifter is designed
to lift the load
, as follows:
1) Make sure the lifter's vacuum generating system is functioning correctly (see MAINTENANCE:
VACUUM TEST).
2) Apply the vacuum pads to the load as previously directed.
3) After the vacuum pumps stop running, place the power switch in the “off” ( ) position.
4) Raise the load a minimal distance, to assure that it is supported by the lifter.
5) Monitor both vacuum gauges while the load is suspended for 5 minutes:
The lifter must
maintain a minimum vacuum level of 10" Hg [-34 kPa] during this time.
If not, the
load does not possess the characteristics required for using this lifter.9
8Contaminated loads can also cause the vacuum pumps to run frequently or continuously. Since excessive pumping quickly
reduces battery energy, the operator should clean the load when possible, to minimize pumping.
9Certain load materials are too rough or porous to allow the lifter to form a seal which can be maintained for 5 minutes without
power. However, in geographical locations where CE Standards do not apply, it may be possible to use the lifter to lift such loads.
Contact Wood’s Powr-Grip for more information.