x-sense XS01-WR User manual

X-Sense
Wireless Interlinked Smoke Alarm
XS01-WR
User Manual
This user manual contains important information regarding the operation of your X-SENSE smoke
alarm. Ensure you read this user manual fully before installing and operating the alarm. If you are
installing this smoke alarm for use by others, you must leave this manual (or a copy of it) with the end
user.
Package Contents
1 ×Alarm Unit
1 ×Mounting Bracket
2 ×Screws
2 ×Anchor Plugs
1 ×User Manual
Safety Information
IMPORTANT!
1. DANGERS, WARNINGS, AND CAUTIONS ALERT YOU TO IMPORTANT OPERATING
INSTRUCTIONS OR TO POTENTIALLY HAZARDOUS SITUATIONS. PAY SPECIAL
ATTENTION TO THESE SITUATIONS.
2. THIS ALARM IS NOT INTENDED TO ALERT HEARING IMPAIRED INDIVIDUALS. THE
USE OF ALCOHOL OR DRUGS MAY ALSO IMPAIR ONE’S ABILITY TO HEAR THE
SMOKE ALARM.
3. FIRES IN CHIMNEYS, WALLS, ROOFS, DIFFERENT LEVELS OR BEHIND CLOSED
DOORS MIGHT NOT BE DETECTED.
4. THIS DEVICE DOES NOT DETECT FLAMES, HEAT, CARBON MONOXIDE OR OTHER
HAZARDOUS GASES.
WARNING!

1. NEVER IGNORE ANYALARM. FAILURE TO RESPOND CAN RESULT IN SERIOUS
INJURY OR DEATH.
2. THE SILENCE FEATURE IS ONLY FOR YOUR CONVENIENCE AND WILL NOT
CORRECT A PROBLEM. ALWAYS CHECK YOUR HOME FOR A POTENTIAL PROBLEM
AFTER ANYALARM. FAILURE TO DO SO CAN RESULT IN INJURY OR DEATH.
3. TEST THIS SMOKE ALARM ONCE AWEEK. IF THE ALARM EVER FAILS TO TEST
CORRECTLY, REPLACE IT IMMEDIATELY! IF THE ALARM CANNOT WORK PROPERLY,
IT WILL NOT ALERT YOU TO A PROBLEM.
Set up and Interconnect Smoke Alarms
All XS01-WRalarms contain a built-in RF module that enables you to wirelessly connect 2 or more
smoke alarms and create aninterlinked network. When one unit is triggered, all interconnected units
will sound an alarm.
The XS01-WR wireless smoke alarms in one multi-pack have already been
interconnected. The alarms in each multi-pack have their own independent interlinked
network. So, if you have more than one multi-pack, you will need to add them all into
the same interlinked network.
How to Interconnect
1. To power on 2 smoke alarms, remove the battery insulating films from their battery compartments.

Note: Make sure that only 2 smoke alarms are powered on at a time to ensure successful
interconnection.
2. Press the test/silence button on one of the 2 smoke alarms 4 times, and this alarm will beep once
andthe red LED will flash continuously, indicating it has entered theinterconnecting mode. After
successfully creating an interlinked network, this alarm will beep once and automatically exit
theinterconnecting mode. To ensure that all smoke alarms enter the same interlinked network,
make sure only one smoke alarm enters interconnecting mode at a time.
3. If you want to interconnect a third smoke alarm, power it on and press the test/silence button 4
times to interconnect to the previously interconnected smoke alarms. Up to 24 smoke alarms can
be interconnected this way.
4. Test the smoke alarms according to the steps in the section “Alarm Test”.
NOTES
1. The smoke alarm will be in the interconnecting mode for 60 seconds, during which the red LED
light flashes. After60 seconds, repeat step 2 to connect the alarms. If needed, manually press the
test/silence button to stop sending out an RF signal, and the red LED will stop flashing and the
alarm will enter normal status.
2. Test all your wireless smoke alarms to ensure that they are interconnected before installation.
3. A maximum of 24 wireless smoke alarms can be interconnected.
4. Note that the XS01-WR alarm can only be interconnected with other X-Sense wireless alarms.
How to Disconnect
Press the test/silence button4 times and the smoke alarm will beep once, then hold down the button
until it beeps once to disconnect. After disconnecting, you can connect it again to let it enter the
interlinked network.

Alarm Test
The alarm must be properly attached to the mounting bracket before it can be tested.
If your XS01-WR is interconnected to other wireless smoke alarms, we recommend that every
individual smoke alarm is tested during the weekly test.
Test a single alarm
Test all interconnected smoke alarms
Action
Press thetest/silencebutton.
Hold down the test/silence button.
Indication
The alarm will sound 3 short quick
beeps.
The red LED will flash once every
second during the audible signal.
The initiating smoke alarm will beep
continuously with the red LED flashing.
Other interconnected smoke alarms in
the network will receive the signal after
5 seconds, and they will beep
continuously with the red LED flashing.
Release the test/silence button and all the
smoke alarms will stop testing.
The alarm testing should be completed
within 3 minutes.
NOTE
The test function accurately tests the alarm’s smoke sensing circuit without the need of test smoke. If
your smoke alarm fails to give an audible test signal, please refer immediately to the troubleshooting
guide at the end of this manual.

Installation Positioning
1. Prioritize the installation of an alarm in the bedroom and walkways, and make sure you can hear
the alarm from all sleeping areas. In a home with several bedrooms, install an alarm in every
bedroom. If you install only one smoke alarm in your home, install the alarm near to all bedrooms
where possible, and not in a basement or furnace room.
2. Install an alarm above the stairway and on every floor of the house.
3. Smoke, heat and anything burning will spread horizontally after rising to the ceiling, so install the
alarm in the middle of the ceiling where possible. Ensure that the alarm is installed at the minimum
distance away from corner.
4. If an alarm cannot be installed in the middle of a ceiling, install it at a distance of 20 inches (50 cm)
away from the corners of the room.
5. If an alarm is installed onto a wall, a distance of 4-12 inches (10-30 cm) should be kept below the
ceiling.

6. If the length of a room or hall is beyond 30 feet (900 cm), several alarms should be installed in the
same space.
7. When the wall or ceiling is angled, the alarm needs to be installed within 3 feet (90 cm) of the
highest wall or ceiling point (measured horizontally) in the room.
8. In multi-level houses or apartments, install at least one wireless smoke alarm on each level and
keep them installed in a straight vertical line(see diagram) with as few obstacles between each of
the interconnected alarms as possible to ensure optimal signal transmission.

Locations toAvoid:
1. Near large metal surfaces and/or bundles of wire.
2. Near fluorescent lights, amateur radios, electrical equipment, or other devices that may transmit an
RF signal, as electronic “noise”may cause nuisance alarms.
WARNING!
1. THIS ALARM SHOULD BE INSTALLED BY A COMPETENT PERSON.
2. ALARMS SHOULD NOT BE USED AS A SUBSTITUTE FOR PROPER INSTALLATION, USE
AND MAINTENANCE OF FUEL BURNING APPLIANCES INCLUDING APPROPRIATE
VENTILATION AND EXHAUST SYSTEMS.
Installation Method
1. Use the mounting bracket to mark the screw holes on the ceiling or the wall.

2. Drill holes at the two marks using an appropriately-sized drill bit. Insert the anchor plugs and
screw the mounting bracket using the screws provided.
3. Attach the alarm to the mounting bracket and turn clockwise to lock the alarm.
4. Test the smoke alarm according to the steps in the section“Alarm Test”.
NOTE: Before installation, it is recommended to test the interconnected smoke alarms in
different rooms where you intend to install these alarms to ensure that they are within the
transmission range.
Battery Replacement
1. To replace the battery, detach the smoke alarm from the mounting bracket by twisting
counterclockwise.
2. Pull the battery removal tab to remove the battery, and then install a new battery, matching the
correct polarity markings.
3. Test the alarm, and then mount the alarm onto themounting bracket by twisting clockwise to lock
the alarm.

LED Indicator andAudible alarm
Status
LED indicator
Audible alarm
Action
Normal
Red LED flashes
once every 60
seconds.
None
Alarm
Red LED flashes
once every
second.
Short quick
beeps
Test
Single Smoke Alarm
Red LED flashes
once every
second.
3 short quick
beeps
Press the
test/silence
button once.
All interconnected smoke
alarms in the network
Red LED flashes
once every
second.
Continuous
beeping until
you release the
test/silence
button
Hold down the
test/silence
button.
Silence Mode
Red LED flashes
once every 5
seconds.
None
Low Battery
Red LED flashes
once every 60
seconds.
1 beep every
60 seconds
Each alarm
gives an
independent
Ala
rm
so
un
der
Green, Red & Yellow LED

warning.
Malfunction
Red LED flashes
twice every 40
seconds.
2 beeps every
40 seconds
Each alarm
gives an
independent
warning.
Silence Mode
If you press the silence button during an alarm state, the unit will be in the silence mode for 9 minutes.
During the silence mode, the red LED will flash once every 5 seconds. The alarm will enter the normal
mode after 9 minutes.
NOTES
1. Mute all other interconnected alarms by pressing the silence button on the initiating smoke
alarm. Note that the initiating smoke alarm cannot be silenced by pressing the silence button
on any other interconnected alarm.
2. Under interconnected condition, the initiating smoke alarm cannot be triggered again during
the 9-minute silence duration. However, all other interconnected alarms can be triggered
when detecting dangerous smoke levels during the silence mode.
Technical Specifications
Power Supply
Replaceable3V CR123A lithium battery
Operating Life
10 years
Battery Life
5 years
Sensor Type
Photoelectric
Safety Standard
EN 14604:2005+AC:2008
Standby Current
< 15 uA (avg.)
Alarm Current
< 150 mA (avg.)
Coverage Area
20-40 m2
Best Operating Ambient
Temperature
4.4-37.8 ℃

Note: Battery life is calculated based on the current rating in the weekly testing mode andthe
standby mode. If its operation mode changes to alarm condition, the battery life will be decreased
accordingly.
Maintenance
To keep your smoke alarm in good working order, follow these simple steps:
1. Verify the unit's alarm sound and indicator are working properly by testing the unit once a week.
2. As a minimum your smoke alarm should be cleaned once every 3 months: Remove the unit from
the ceiling and clean the alarm cover and vents with your vacuum cleaner fitted with the soft brush
attachment to remove dust and dirt.
3. Never use detergents or other solvents to clean the unit.
4. Avoid spraying air fresheners, hair spray or other aerosols near the alarm.
5. Do not paint the unit. Paint will seal the vents and interfere with the sensor’s ability to detect fire.
6. Never attempt to disassemble the unit or clean inside. Doing so will void your warranty.
7. When removed, place the smoke alarm back in its proper location as soon as possible, to assure
continuous protection from fire.
8. When household cleaning supplies or similar contaminants are used, the area should be ventilated.
Operating Relative
Humidity
≤ 85% (non-condensing)
Alarm Loudness
≥ 85 dB at 3 m @ 3.2 ± 0.3 kHz pulsing alarm
Silence Duration
About 9 minutes
Operating Frequency
915.275 MHz
Transmission Power
18 dBm
Maximum Number of
Interconnected Units
24 wireless units (only compatible with X-Sense wireless alarms)
Transmission Range
Over 250 m in open air

Troubleshooting
PROBLEM
SOLUTION
Your smoke alarm does not sound
during testing.
Please check whether the alarm is properly attached to the
mounting bracket.
Make sure you push the central test button firmly.
Check the installation positioning. The wireless signal
might be blocked or out of range.
False alarms triggered
intermittently or when residents are
cooking, taking showers, etc.
Check the location of your smoke alarm (see “Installation
Positioning”).
Clean the smoke alarm (see “Maintenance”).
Red LED flashes and the alarm
sounds one beep every 60 seconds.
The battery is low. Replace the alarm immediately.
Red LED flashes and the alarm
sounds two beeps every 40 seconds.
The alarm is malfunctioning. Please clean your smoke alarm, or
replace the alarm immediately.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Environmental Protection
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with Local Authority or retailer for recycling advice.
Manufacturer and Service Information
X-Sense Innovations Co., Ltd.
Address: B4-503-D, Tower B, Kexing Science Park, No. 15 KeyuanRoad, Technology Park
Community, Yuehai Avenue, Nanshan District,Shenzhen, 518057, CHINA
Email: [e-mail]