Xtracycle PeaPod LT Instruction Manual

Bicycle riding is
inherently dangerous.
Users must read this
User’s Guide before
using the seat.
Always wear approved
helmet and safety
equipment.
Become accustomed to
the longer bike before
riding on the street.
DO NOT overload or
bike may become
unstable.
DO NOT carry
passengers unless
properly equipped to do
so.
User’s Guide &
Installation Instructions
It is recommended that a professional bicycle
shop assemble and install PeaPod LT on your
rack equipped bicycle or Xtracycle.
It is imperative that you read this owner’s
manual prior to installation.
Load Limit: 22 kgs/48.5 lbs
48
POUNDS
22
KILOGRAMS
Failure to observe this load maximum and all
warnings could result in serious injury or death.
4mm + 5mm*
Allen keys,
10mm box
wrench
and/or
socket.
10MM BOX WRENCH 10MM
Rack Width 120~175mm
Tube Dia. 8~16mm
CHECK
CENTER OF
GRAVITY
REAR
WHEEL
AXIS
90°
10cm10cm
PeaPod LT has a Center of Gravity
mark on each side of the seat. If this
mark is more than 10cm off the
vertical rear wheel axis, your bicycle
is not suitable to install and use this
child seat.
WARNING MAXIMUM LOAD
STANDARD RACK
FITTING REQUIREMENTS
RACK MAX/MIN*
TOOLS REQUIRED
*Only included with optional Xtracycle Accessory Kit
*Only applies to standard
bicycle install

• When not carrying a child, fasten the retention system buckles so the straps do not hang loosely.
• Check child seat’s surface temperature before seating your child. Direct exposure to the sun will
increase the surface temperature, potentially burning your child.
• Mount and dismount your bicycle in a manner that allows you to maintain full control of the bicycle
and avoid striking your child with your foot as you mount.
• Ensure bicycle is stable and under your control when loading and unloading child.
• When transporting the bicycle outside of another vehicle, remove child seat. Air turbulence might
damage the seat or loosen its fastening to the bicycle, potentially resulting in failure when used.
• Dress your child warmly during use. Properly outfit your child with rain protection in inclement
weather.
• Always use an approved helmet for yourself and your child.
• Please notify your dealer for replacement if any component is missing or broken.
• A rear reflector that complies with CPSC regulations must be visible whether the carrier is on the
bicycle or not.
MAINTENANCE
Your child seat is relatively easy to maintain, please follow these procedures to ensure safe and
trouble-free use.
• Check the condition and fastness of all parts attaching to the child seat, FlightDeck and Super-
Hooks before each use.
• Keep the seat cushion hygienic by washing it regularly. Hand wash with mild detergent.
WARNING
• DO NOT exceed 22 kgs/48.5 lbs if using seat to carry cargo.
• DO NOT carry additional cargo if using seat on a standard rack.
• DO NOT attach any accessories or luggage to the child seat due to the potential for exceeding
maximum weight specifications.
• DO NOT park and leave your bicycle unattended while child is in seat.
• NEVER leave the child in a carrier with the bicycle supported only by a kickstand.
• NEVER ride in inclement or hazardous conditions.
• NEVER ride your bicycle at night without adequate lighting.
• Modification of any part of the child seat or its accessories is prohibited.
• Bicycle handling and riding characteristics will differ from riding without a child seat due to shift-
ing weights and balance. Practice steering, braking and pedaling before carrying your child.
• Stop immediately if any part malfunctions. DO NOT continue to ride if parts are broken.
• ALWAYS ensure the safety strap is always secured and tightened to the MAIN bicycle frame.
• WARNING! Failure to comply with the manufacturer’s instructions can lead to serious injury or
death of the passenger/rider!
WARNING
PLEASE READ AND FOLLOW ALL PRE-INSTALLATION, USE, CARE, MAINTENANCE AND
WARNING GUIDELINES BELOW TO ENSURE THE SAFETY OF YOUR CHILD AND YOURSELF
WHEN USING THIS CHILD SEAT
PRE-INSTALLATION
• PeaPod LT is ONLY designed to be mounted to a bicycle rear rack, an approved Xtracycle cargo
sport utility bicycle or other LongTail Standard compliant bicycle.
• PeaPod LT must ONLY be mounted to a standard bicycle rear rack or Xtracycle using the supplied
hardware. Installation on an Xtracycle requires FlightDeck, SuperHooks and Whatchamacollars.
PeaPod LT must NOT be used with the SnapDeck, TekDeck, or SnapHooks for installation or use.
Installation of PeaPod LT on an Xtracycle with anything other than the FlightDeck, SuperHooks and
Whatchamacollars will void warranty & could lead to product failure, serious injury and/or death.
• PeaPod LT must be installed to a bicyle or Xtracycle that is in good working order, able to handle
the additional load and is of proper size and adjustment for the rider. Ensure the standard bicycle
rack is properly installed. If in doubt, refer to or obtain information from the bicycle & bicycle rack
manufacturer.
USE & CARE
• The PeaPod LT child seat is designed to carry one child who’s age is younger than 7 years-old and
older than 12 months, who can sit upright by him/herself and weighs no more than 22 kgs/48.5 lbs.
Never exceed these limits!
• Bicycle operator’s age must be at least 18 years old.
• Ensure initially, and check from time to time, that your child’s age, size and weight are within age,
weight and fitness requirements.
• DO NOT carry a child that is too young to sit safely in the seat. Carry only children that are able to
sit unaided for a sustained period of time.
• Before use, check to ensure there are no sharp edges or objects near or in the seating area (e.g.
broken plastic).
• Before each ride, ensure the mounted carrier does not interfere with braking, pedaling, or steer-
ing of the bicycle.
• Ensure there is no possibility of child’s body or clothing contacting any moving part of the bicycle.
Avoid scarfs or clothing with long sections that may become wrapped in any moving parts.
• Ensure the child seat harness is fastened correctly and securely over child. Depending on your
child’s size, you may need to thread the shoulder harnesses through the seat in a lower or higher
position.
• Always ensure child’s feet are properly secured in foot rests and strapped in.
• Cover any exposed rear saddle springs to avoid possible pinching injury using the provided plastic
spring covers.
• Always use the restraint system. Children unable to remain calm and seated while riding are
recommended not to use the seat until able to remain calm. Also ensure the restraint system is
not loose or able to be caught in any moving parts, including the wheels.
Page 2

• When not carrying a child, fasten the retention system buckles so the straps do not hang loosely.
• Check child seat’s surface temperature before seating your child. Direct exposure to the sun will
increase the surface temperature, potentially burning your child.
• Mount and dismount your bicycle in a manner that allows you to maintain full control of the bicycle
and avoid striking your child with your foot as you mount.
• Ensure bicycle is stable and under your control when loading and unloading child.
• When transporting the bicycle outside of another vehicle, remove child seat. Air turbulence might
damage the seat or loosen its fastening to the bicycle, potentially resulting in failure when used.
• Dress your child warmly during use. Properly outfit your child with rain protection in inclement
weather.
• Always use an approved helmet for yourself and your child.
• Please notify your dealer for replacement if any component is missing or broken.
• A rear reflector that complies with CPSC regulations must be visible whether the carrier is on the
bicycle or not.
MAINTENANCE
Your child seat is relatively easy to maintain, please follow these procedures to ensure safe and
trouble-free use.
• Check the condition and fastness of all parts attaching to the child seat, FlightDeck and Super-
Hooks before each use.
• Keep the seat cushion hygienic by washing it regularly. Hand wash with mild detergent.
WARNING
• DO NOT exceed 22 kgs/48.5 lbs if using seat to carry cargo.
• DO NOT carry additional cargo if using seat on a standard rack.
• DO NOT attach any accessories or luggage to the child seat due to the potential for exceeding
maximum weight specifications.
• DO NOT park and leave your bicycle unattended while child is in seat.
• NEVER leave the child in a carrier with the bicycle supported only by a kickstand.
• NEVER ride in inclement or hazardous conditions.
• NEVER ride your bicycle at night without adequate lighting.
• Modification of any part of the child seat or its accessories is prohibited.
• Bicycle handling and riding characteristics will differ from riding without a child seat due to shift-
ing weights and balance. Practice steering, braking and pedaling before carrying your child.
• Stop immediately if any part malfunctions. DO NOT continue to ride if parts are broken.
• ALWAYS ensure the safety strap is always secured and tightened to the MAIN bicycle frame.
• WARNING! Failure to comply with the manufacturer’s instructions can lead to serious injury or
death of the passenger/rider!
PRE-INSTALLATION
• PeaPod LT is ONLY designed to be mounted to a bicycle rear rack, an approved Xtracycle cargo
sport utility bicycle or other LongTail Standard compliant bicycle.
• PeaPod LT must ONLY be mounted to a standard bicycle rear rack or Xtracycle using the supplied
hardware. Installation on an Xtracycle requires FlightDeck, SuperHooks and Whatchamacollars.
PeaPod LT must NOT be used with the SnapDeck, TekDeck, or SnapHooks for installation or use.
Installation of PeaPod LT on an Xtracycle with anything other than the FlightDeck, SuperHooks and
Whatchamacollars will void warranty & could lead to product failure, serious injury and/or death.
• PeaPod LT must be installed to a bicyle or Xtracycle that is in good working order, able to handle
the additional load and is of proper size and adjustment for the rider. Ensure the standard bicycle
rack is properly installed. If in doubt, refer to or obtain information from the bicycle & bicycle rack
manufacturer.
USE & CARE
• The PeaPod LT child seat is designed to carry one child who’s age is younger than 7 years-old and
older than 12 months, who can sit upright by him/herself and weighs no more than 22 kgs/48.5 lbs.
Never exceed these limits!
• Bicycle operator’s age must be at least 18 years old.
• Ensure initially, and check from time to time, that your child’s age, size and weight are within age,
weight and fitness requirements.
• DO NOT carry a child that is too young to sit safely in the seat. Carry only children that are able to
sit unaided for a sustained period of time.
• Before use, check to ensure there are no sharp edges or objects near or in the seating area (e.g.
broken plastic).
• Before each ride, ensure the mounted carrier does not interfere with braking, pedaling, or steer-
ing of the bicycle.
• Ensure there is no possibility of child’s body or clothing contacting any moving part of the bicycle.
Avoid scarfs or clothing with long sections that may become wrapped in any moving parts.
• Ensure the child seat harness is fastened correctly and securely over child. Depending on your
child’s size, you may need to thread the shoulder harnesses through the seat in a lower or higher
position.
• Always ensure child’s feet are properly secured in foot rests and strapped in.
• Cover any exposed rear saddle springs to avoid possible pinching injury using the provided plastic
spring covers.
• Always use the restraint system. Children unable to remain calm and seated while riding are
recommended not to use the seat until able to remain calm. Also ensure the restraint system is
not loose or able to be caught in any moving parts, including the wheels.
PPLT-CAUTION2
Page 3

Designed for use on a
standard bicycle rack
or an Xtracycle,
PeaPod LT is a fun,
easy way to carry
your child.
1
For your child’s safety and yours,
please check your rack’s integrity
and fastness to your bicycle frame.
Check all welds for signs of
hairline cracking or separation.
DO NOT USE IF
CRACKED/DAMAGED.
Ensure all attachment
points are tightened
and the rack is
properly installed.
Refer to the rack
manufacturer’s
manual for proper
install information.
NSuperHook
(4)
P4mm
T-handle
(1)
MWhatchamacollar
(2)
J PeaPod LT
Seat (1)
K Carriage
Rail (4)
E Saddle
Spring
Cover (2)
AFootrest (2)
LFlightDeck (1)
B 5mm
Thick
Washer
(4)
O40mm
Countersink
Bolt
(4)
C10mm
Nyloc
Nut (4)
D Carriage Rail
Protector (16)
Carriage
Bolts
G 45mm (4)
H 20mm (2)
I 15mm (2)
FBolt
Cap (4)
2
Snap footrests (A) into PPLT body (J) at
appropriate foot height for your child.
Hook the top two tabs in first then rotate
down until you hear a loud ‘click’.
CLICK
PeaPod LT Bits ‘n Pieces
Optional Xtracycle Accessory Kit Bits n Pieces
Tools Needed: 4mm Allen Key & 10mm Box/Socket Wrench
IMPORTANT! PRE-INSTALL SAFETY CHECK
Standard Rack Install
A
J
Page 4 PPLT-INSTRUCT1

3
Securely attach the security strap to
either the seatpost or the seat tube
by tightly wrapping the velcro around
the part chosen. Remove any slack to avoid
catching the strap in the wheel or drive train.
Place the loose carriage rails (K) onto your rack
to identify which of set of holes to use for install.
4
6 7
5
Using a 10mm box wrench or socket, loosen and remove the
locknuts (C) and washers (B) off the carriage bolts (H, I).
Remove the 45mm carriage bolts (G) and re-insert into the
outer holes of the carriage rails (K).
Re-insert the 20mm carriage bolts (H) into the forward seat
basin holes and the 15mm carriage bolts into the rear seat
basin holes (I). Re-install the washers (B) and locknuts (C).
To protect your rack’s rails, insert
the carriage rail protectors (D) onto
the flanges of the carriage rails (K).
Place PeaPod LT into your desired
position as found in Step 5. Ensure
the seat is facing forward on the
rack.
Insert the lower carriage rails (K)
onto the 45mm carriage bolts (G)
with a washer and nut
(B, C). Ensure all nuts
are securely tightened.
Finish off bolt ends
with the bolt caps (F).
Grab the assembled
seat and give it a good
shake to ensure the
attachment is solidly
attached and not in
danger of loosening.
Setup shown for narrow rack
install. Use outer holes for
wide rack installs.
Place PeaPod LT onto your rack and align the Center of Gravity mark
on the side of the seat basin directly above the rear wheel axle. You
have 10cm of forward/aft adjustment. DO NOT go beyond these
margins! Don’t forget to check for pedal clearance of the seat legs.
If your rack requires the use of
the outer set of holes, you will
need to follow Step 4 for
dissassembly of PPLT’s carriage
rails and bolts and reassemble
with the 45mm bolts (G) in the
outer holes.
If your rack is suited for the
narow set of holes, please skip
Step 4 and continue with Step 5.
FRONT
FRONT
Inner Holes for Narrow Racks
(PPLT comes pre-assembled in this configuration)
Outer Holes for Wide Racks
I
B
BB
B
C
C
C
C
I
A
B
H
K
K
K
K
K
J
J
K
K
H
CHECK
CENTER OF
GRAVITY
REAR
WHEEL
AXIS
90°
10cm10cm
G
G
G
G
G G
G
G
D
B
B
B
C
F
C
C
F
F
D
D
K
K
D
Pre-Ride Warnings on Page 9
Page 5

Make sure the
cam strap has a
simple knot in it
before attaching
to shorten
overall length.
2
Remove deck and racks from Xtracycle.
3”
1
Snap in footrests (A) at appropriate
foot height for your child.
Hook the top two tabs in first then
rotate down until you hear a loud
‘click’.
3
Install Whatchamacollars (WMC, M) by
following instructions on card. Liberally
grease surfaces of WMC and rack before
installation to help with installation.
Big Dummy users, please review this blog
post before installing: http://bit.ly/bd-wmc
Install WMC on fore tubes of each rack.
Reinsert racks and tighten WMC.
CLICK
Tools Needed: 4mm & 5mm Allen Key,10mm Box/Socket Wrench &
CamStrap/Belt/Friend to tension racks
Xtracycle Installation
M
A
J
5
Install the four 40mm countersink bolts (O) into FlightDeck's (L)
countersunk holes. You must use these four countersunk
holes to achieve a proper clamp on your Xtracycle racks.
From underneath
FlightDeck, screw
SuperHooks (N) onto
countersunk bolts
about five complete
turns so that they’re on,
but loose.
You will tighten the
SuperHooks during
Step 9.
Before installing FlightDeck (L), it will help to pull your racks toward
each other. A few ways to do this are: 1Use a CamStrap by tying
a knot in the cam end, then wrapping the cam around one rack,
passing through its loop end. Take the long strap and wrap
around the other rack, passing through its loop end. Pass the
long strap through the cam and tighten. 2You may also use a
belt/strap/rope to draw the racks toward each other. 3Enlist a
friend to help push the racks together during Step 9.
41
2
N
L
OFlightDeck
40mm
Countersink Bolt
SuperHook
Rear hooks have two
hole options for easier
positioning around your
FreeLoaders
O O
O O
N
NN
N
L
Page 6

Optional hook
mounting holes
6
Your FlightDeck allows for multiple child seat and child passen-
ger positions. Your ideal PeaPod positioning will depend on
your Xtracycle’s geometry, handling characteristics and personal
preference.
Your PeaPod can install in ten different positions. Positions 1-7 &
10 allow you to keep PeaPod and FlightDeck assembled giving
you the ability to loosen the SuperHooks if you want to remove
the child seat assembly and use your SnapDeck or TekDeck.
Using PeaPod in positions 1-6 provides better handling and
weight balance.
Positions 8 & 9 require separate installation and removal of
PeaPod and FlightDeck due to access limitation of the rear
SuperHooks.
To install two PeaPod LT seats, install the forward seat in
positions 1 & 9 or positions 2 & 10. Always practice riding and
testing your child seat setup before riding with your children.
Positions
1, 2 , 3
Positions
4 , 5 , 6
Forward
Better Handling
Weight closer to center of gravity.
Requires saddle and rider’s heel clearance.
Standard
Decent Handling
Weight centered over rear wheel axle.
Good clearance between child and rider.
Older Child
Potentially
Difficult
Seat weight sits behind
axle, affecting handling.
Recommended only for
strong, experienced
riders.
Two Seat Setup
Potentially
Difficult
PeaPod LT and the
Xtracycle Accessory Kit
are certified for use with
two PeaPod LT seats.
Positions able to be used
for two seats are 1 & 9 or
2 & 10.
Positions
7, 8 , 9 , 10
Positions
1 & 9 or 2 & 10
Front
Rear
1st Position
5th Position
10th Position
N
N N
N
L
O O
OO
PeaPod Positioning Options
Page 7

B C
9
Place FlightDeck (L) with
SuperHooks (N) loosely
installed on top of racks.
Install one side at a time.
Twist SuperHooks so that
they are aligned with and
snug to V-racks.
SuperHooks clamp to V-racks
outside of the fabric hangers
of your FreeLoader bag. Avoid clamping on the
curved section of your racks to prevent deck bowing.
Once SuperHooks are in proper place, tighten one
side until firmly secure. With one side complete,
repeat steps for other side. If the rack distance is
too wide, cinch down on CamStrap, belt or have a
friend squeeze them together until SuperHooks are
completely under V-rack. Tighten SuperHooks and
remove CamStrap or belt when install is finished.
NO!
FlightDeck (L)
40mm Countersink
Bolt (O)
SuperHook
(N)
V-rack
tube
8
With your PeaPod LT (J) bolted in your
desired seat position, insert the security
strap through the front handle opening
at the nose of the FlightDeck (L). The
Velcro section of the strap should
reach the main frame of your
bicycle. Adjust the strap length as
necessary to remove excess slack.
Securely attach the security strap to either the seatpost or the seat tube.
Do not attach to V-racks or Adventure Racks!
7
Positions 8 & 9 require FlightDeck to be installed onto
your racks first. Complete Step 9 before continuing
with Steps 7 & 8.
Insert 45mm carriage bolts (G) into FlightDeck (L) at
desired postion (see Page 7 for options and recommen-
dations).
Install a washer (B) and locknut (C) on each of the 45mm
carriage bolts (G). Tighten down with a 10mm spanner
or socket until snug. You may need to pull on the bolt, or
push on the bolt from inside the seat basin, while you
tighten to ensure it does not spin as the nut is bolted on.
Periodically check the tightness of these nuts, and all
attachments, over time to ensure your child’s safety.
Place the assembled PeaPod LT and FlightDeck onto
your racks. Twist the SuperHooks so that the hook end is
underneath your racks.
Securely attach
Velcro end to
seatpost or
seat tube
If using positions 8 & 9, you must install FlightDeck on racks first!
FRONT
A
B
BB
B
C
C
J
J
K
K
GG
G
G
L
L
C
C
N
N
N
N
N
Shown
without bags
for clarity.
Page 8

E
Wrap one saddle spring cover (E) around each
exposed saddle spring. Insert the plastic arrow into
the cut slot on the tail of the cover to form a
protective tube.
This is used to prevent your child from injuring
themself by placing his/her fingers into the spring.
DO NOT have your child inside
the seat during these tests.
Double check all nuts and contact points for
tightness. Examine your rear rack’s welds and
connection points for hairline cracking and
fatigue. DO NOT use if any part of your rear
rack appears compromised or defective.
Test the firmness of the attachments by grabbing
the seat body and shaking the assembly. Check
for any rattles or excess flex in the assembly.
Take your chariot for a spin without child to get a
feel for how it rides, also practice mounting and
dismounting to ensure you won't accidentally kick
your child.
Never leave a child unattended in PeaPod LT,
always be within arms reach if your child is
strapped in. Excessive movement and flailing by your
child could result in toppling your bicycle potentially
causing serious injury or death.
Always put a helmet on your child. They’re your most
precious cargo.
READ BEFORE FIRST RIDE! |SAFETY & TEST RIDE INFORMATION
Standard Rack Install Safety & Test Ride Information
Xtracycle Install Safety & Test Ride Information
DO NOT have your child inside
the seat during these tests.
Double check all your bolts for tightness and examine your
SuperHooks to ensure they're fully grabbing your V-racks and
haven't twisted out of place. If your saddle has exposed
springs, cover them with the provided covers.
Test the firmness of the attachments by grabbing the seat
body and shaking the assembly. Check for any rattles or flex
in the assembly.
Take your chariot for a spin without
child to get a feel for how it rides, also
practice mounting and dismounting to
avoid accidentally kicking your child.
Never leave a child unattended
in PeaPod LT, always be within
arms reach if your child is
strapped in. Excessive move-
ment and flailing by your child
could result in toppling your
Xtracycle resulting in serious
injury or death.
Always put a helmet on your
child. They’re your most precious
cargo.
Saddle Spring Protection
Ensure your bicycle is in good mechanical
condition before attempting these safety tests.
Ensure your Xtracycle is in good mechanical condition before
attempting these safety tests.
Page 9

• When not carrying a child, fasten the retention system buckles so the straps do not hang loosely.
• Check child seat’s surface temperature before seating your child. Direct exposure to the sun will
increase the surface temperature, potentially burning your child.
• Mount and dismount your bicycle in a manner that allows you to maintain full control of the bicycle
and avoid striking your child with your foot as you mount.
• Ensure bicycle is stable and under your control when loading and unloading child.
• When transporting the bicycle outside of another vehicle, remove child seat. Air turbulence might
damage the seat or loosen its fastening to the bicycle, potentially resulting in failure when used.
• Dress your child warmly during use. Properly outfit your child with rain protection in inclement
weather.
• Always use an approved helmet for yourself and your child.
• Please notify your dealer for replacement if any component is missing or broken.
• A rear reflector that complies with CPSC regulations must be visible whether the carrier is on the
bicycle or not.
MAINTENANCE
Your child seat is relatively easy to maintain, please follow these procedures to ensure safe and
trouble-free use.
• Check the condition and fastness of all parts attaching to the child seat, FlightDeck and Super-
Hooks before each use.
• Keep the seat cushion hygienic by washing it regularly. Hand wash with mild detergent.
WARNING
• DO NOT exceed 22 kgs/48.5 lbs if using seat to carry cargo.
• DO NOT carry additional cargo if using seat on a standard rack.
• DO NOT attach any accessories or luggage to the child seat due to the potential for exceeding
maximum weight specifications.
• DO NOT park and leave your bicycle unattended while child is in seat.
• NEVER leave the child in a carrier with the bicycle supported only by a kickstand.
• NEVER ride in inclement or hazardous conditions.
• NEVER ride your bicycle at night without adequate lighting.
• Modification of any part of the child seat or its accessories is prohibited.
• Bicycle handling and riding characteristics will differ from riding without a child seat due to shift-
ing weights and balance. Practice steering, braking and pedaling before carrying your child.
• Stop immediately if any part malfunctions. DO NOT continue to ride if parts are broken.
• ALWAYS ensure the safety strap is always secured and tightened to the MAIN bicycle frame.
• WARNING! Failure to comply with the manufacturer’s instructions can lead to serious injury or
death of the passenger/rider!
PRE-INSTALLATION
• PeaPod LT is ONLY designed to be mounted to a bicycle rear rack, an approved Xtracycle cargo
sport utility bicycle or other LongTail Standard compliant bicycle.
• PeaPod LT must ONLY be mounted to a standard bicycle rear rack or Xtracycle using the supplied
hardware. Installation on an Xtracycle requires FlightDeck, SuperHooks and Whatchamacollars.
PeaPod LT must NOT be used with the SnapDeck, TekDeck, or SnapHooks for installation or use.
Installation of PeaPod LT on an Xtracycle with anything other than the FlightDeck, SuperHooks and
Whatchamacollars will void warranty & could lead to product failure, serious injury and/or death.
• PeaPod LT must be installed to a bicyle or Xtracycle that is in good working order, able to handle
the additional load and is of proper size and adjustment for the rider. Ensure the standard bicycle
rack is properly installed. If in doubt, refer to or obtain information from the bicycle & bicycle rack
manufacturer.
USE & CARE
• The PeaPod LT child seat is designed to carry one child who’s age is younger than 7 years-old and
older than 12 months, who can sit upright by him/herself and weighs no more than 22 kgs/48.5 lbs.
Never exceed these limits!
• Bicycle operator’s age must be at least 18 years old.
• Ensure initially, and check from time to time, that your child’s age, size and weight are within age,
weight and fitness requirements.
• DO NOT carry a child that is too young to sit safely in the seat. Carry only children that are able to
sit unaided for a sustained period of time.
• Before use, check to ensure there are no sharp edges or objects near or in the seating area (e.g.
broken plastic).
• Before each ride, ensure the mounted carrier does not interfere with braking, pedaling, or steer-
ing of the bicycle.
• Ensure there is no possibility of child’s body or clothing contacting any moving part of the bicycle.
Avoid scarfs or clothing with long sections that may become wrapped in any moving parts.
• Ensure the child seat harness is fastened correctly and securely over child. Depending on your
child’s size, you may need to thread the shoulder harnesses through the seat in a lower or higher
position.
• Always ensure child’s feet are properly secured in foot rests and strapped in.
• Cover any exposed rear saddle springs to avoid possible pinching injury using the provided plastic
spring covers.
• Always use the restraint system. Children unable to remain calm and seated while riding are
recommended not to use the seat until able to remain calm. Also ensure the restraint system is
not loose or able to be caught in any moving parts, including the wheels.
THIS PAGE INTENTIONALLY LEFT BLANK
Page 10

• When not carrying a child, fasten the retention system buckles so the straps do not hang loosely.
• Check child seat’s surface temperature before seating your child. Direct exposure to the sun will
increase the surface temperature, potentially burning your child.
• Mount and dismount your bicycle in a manner that allows you to maintain full control of the bicycle
and avoid striking your child with your foot as you mount.
• Ensure bicycle is stable and under your control when loading and unloading child.
• When transporting the bicycle outside of another vehicle, remove child seat. Air turbulence might
damage the seat or loosen its fastening to the bicycle, potentially resulting in failure when used.
• Dress your child warmly during use. Properly outfit your child with rain protection in inclement
weather.
• Always use an approved helmet for yourself and your child.
• Please notify your dealer for replacement if any component is missing or broken.
• A rear reflector that complies with CPSC regulations must be visible whether the carrier is on the
bicycle or not.
MAINTENANCE
Your child seat is relatively easy to maintain, please follow these procedures to ensure safe and
trouble-free use.
• Check the condition and fastness of all parts attaching to the child seat, FlightDeck and Super-
Hooks before each use.
• Keep the seat cushion hygienic by washing it regularly. Hand wash with mild detergent.
WARNING
• DO NOT exceed 22 kgs/48.5 lbs if using seat to carry cargo.
• DO NOT carry additional cargo if using seat on a standard rack.
• DO NOT attach any accessories or luggage to the child seat due to the potential for exceeding
maximum weight specifications.
• DO NOT park and leave your bicycle unattended while child is in seat.
• NEVER leave the child in a carrier with the bicycle supported only by a kickstand.
• NEVER ride in inclement or hazardous conditions.
• NEVER ride your bicycle at night without adequate lighting.
• Modification of any part of the child seat or its accessories is prohibited.
• Bicycle handling and riding characteristics will differ from riding without a child seat due to shift-
ing weights and balance. Practice steering, braking and pedaling before carrying your child.
• Stop immediately if any part malfunctions. DO NOT continue to ride if parts are broken.
• ALWAYS ensure the safety strap is always secured and tightened to the MAIN bicycle frame.
• WARNING! Failure to comply with the manufacturer’s instructions can lead to serious injury or
death of the passenger/rider!
PRE-INSTALLATION
• PeaPod LT is ONLY designed to be mounted to a bicycle rear rack, an approved Xtracycle cargo
sport utility bicycle or other LongTail Standard compliant bicycle.
• PeaPod LT must ONLY be mounted to a standard bicycle rear rack or Xtracycle using the supplied
hardware. Installation on an Xtracycle requires FlightDeck, SuperHooks and Whatchamacollars.
PeaPod LT must NOT be used with the SnapDeck, TekDeck, or SnapHooks for installation or use.
Installation of PeaPod LT on an Xtracycle with anything other than the FlightDeck, SuperHooks and
Whatchamacollars will void warranty & could lead to product failure, serious injury and/or death.
• PeaPod LT must be installed to a bicyle or Xtracycle that is in good working order, able to handle
the additional load and is of proper size and adjustment for the rider. Ensure the standard bicycle
rack is properly installed. If in doubt, refer to or obtain information from the bicycle & bicycle rack
manufacturer.
USE & CARE
• The PeaPod LT child seat is designed to carry one child who’s age is younger than 7 years-old and
older than 12 months, who can sit upright by him/herself and weighs no more than 22 kgs/48.5 lbs.
Never exceed these limits!
• Bicycle operator’s age must be at least 18 years old.
• Ensure initially, and check from time to time, that your child’s age, size and weight are within age,
weight and fitness requirements.
• DO NOT carry a child that is too young to sit safely in the seat. Carry only children that are able to
sit unaided for a sustained period of time.
• Before use, check to ensure there are no sharp edges or objects near or in the seating area (e.g.
broken plastic).
• Before each ride, ensure the mounted carrier does not interfere with braking, pedaling, or steer-
ing of the bicycle.
• Ensure there is no possibility of child’s body or clothing contacting any moving part of the bicycle.
Avoid scarfs or clothing with long sections that may become wrapped in any moving parts.
• Ensure the child seat harness is fastened correctly and securely over child. Depending on your
child’s size, you may need to thread the shoulder harnesses through the seat in a lower or higher
position.
• Always ensure child’s feet are properly secured in foot rests and strapped in.
• Cover any exposed rear saddle springs to avoid possible pinching injury using the provided plastic
spring covers.
• Always use the restraint system. Children unable to remain calm and seated while riding are
recommended not to use the seat until able to remain calm. Also ensure the restraint system is
not loose or able to be caught in any moving parts, including the wheels.
Insert “T” end of
buckle strap into
the front hole.
Continue passing
end through rear
hole. Snug strap
down so that “T”
end does not pull
through. Check for
secure fit.
CLICK
PRESS
PRESS
PeaPod LT’s seat cushion is removable, allowing
you to hand wash it with mild detergent.
When reinstalling the cushion, take care to
properly fasten and secure all straps to the
PeaPod seat. Failure to properly secure the
straps could cause serious injury or death to
your child.
Pass loop end of
security strap
through front hole
and insert plastic
clip in loop (1)
A After loop is
passed through
the seat, slide
plastic clip into
loop of strap.
B Squeeze the strap
so the edges can
fit into the clip
gap.
C Push the strap
into the gap.
Repeat for the
other strap side.
D Slide the clip to
the end of the
strap loop to
finish.
www.xtracycle.com 888.537.1401 For more PeaPod info, visit: xtracycle.com/peapod
1
1
2
3
3
2
Using and Caring for your PeaPod LT
1
To open buckle, press the two
rounded ends of the male piece in
addition to the safety button in the
middle.
To close buckle, squeeze the sides of male piece and
insert into buckle body. Listen for a positive ‘click’
and tug on harness to ensure a secure connection.
PeaPod LT Seat
w/ Headrest &
Footrests
Installed
Shoulder
Strap Holes
Depending on the
size of your child,
you may need to
use the lower, or
upper, shoulder
strap holes for a
proper fit.
Seat Cushion
(Hand Wash Only)
Seat Harness
& Buckle
A
B
C
D
Security Strap
Securely fasten your
safety strap to the
main bicycle frame
or seatpost.
Attaching Plastic Clips Threading Security Strap and Buckle Strap Into Seat Body
Using Harness Buckle
Pa ge 11

IMPORTANT: THIS IS A LEGAL DOCUMENT PLEASE READ AND UNDERSTAND THIS DOCUMENT
RELEASE AND WAIVER OF LIABILITY
ASSUMPTION OF RISK & INDEMNITY AGREEMENT (“AGREEMENT”)
IN CONSIDERATION of being permitted to use any products associated with “XTRACYCLE”, on behalf of myself, my
personal representatives, assigns, heirs and next of kin, I freely make the following representations and agreements:
1. I am familiar with the XTRACYCLE products (“Product”) and agree to take full responsibility for the use of the
Product. This use will include adhering to all safety rules while riding a bicycle and using the Product, wearing a
helmet at all times (and ensuring all passengers also wear a helmet at all times), using head and tail lights while
riding at night, properly storing the Product and ensuring that the Product and its parts, if any, are correctly
installed, used and maintained. I further agree that if at any time I believe that any conditions that may impact use
of the Product are or seem to be unsafe, I will immediately discontinue further use of the Product.
2. I acknowledge and understand that riding a bicycle and/or riding a bicycle with an extended wheel base with or
without cargo loads (including, without limitation, human passengers, child carriers, animals, groceries, building
materials/supplies, surfboards, kayaks, other bicycles, or any other load) can be a dangerous activity, requiring
strenuous exercise and various degrees of skill and experience.
3. I represent and warrant that I do not have any physical or medical condition that would prevent me from riding a
bicycle and using the Product, or which would endanger myself or others.
4. I fully realize the dangers of bicycling and using the Product and I fully assume all the risks associated with such
use. I understand these risks include, by way of example and not limitation, the following: the dangers of collision
with pedestrians, vehicles, other riders, and fixed or moving objects; the dangers arising from surface hazards,
equipment failure, inadequate safety equipment and weather conditions; property damage or loss; and I under-
stand the serious risks, hazards and dangers of personal injury, including permanent disability, paralysis and
death associated with bicycling and the use of the Product. These risks and dangers may be caused by my own
actions or inactions or the actions or inactions of others, or by other unknown, unforeseeable or foreseeable
causes. I freely and voluntarily elect to use the Product with the knowledge of the risk and danger involved.
5. I understand and agree that the Product is not intended to be used by anyone under the age of 18.
6. I agree that if I authorize any individual(s) other than myself to use the Product, I assume, on behalf of myself and
all other individual(s) using the Product, all liability, risk and responsibility relating in any manner to the use of the
Product.
7. I understand and acknowledge that XTRACYCLE is not an insurer of my behavior and/or actions or inactions, and
that XTRACYCLE assumes no liability whatsoever for personal injuries or property damages to me, my property or
any third party or their property arising from the use of the Product.
8. I hereby agree not to sue XTRACYCLE and all of its officers, administrators, directors, employees, agents and any
other person or entity acting on their behalf (collectively the “Releasees”) and agree to release, forever discharge
and indemnify and save and hold harmless, XTRACYCLE and the Releasees from any and all liability, claims,
losses, damages, demands, actions and causes of actions whatsoever arising out of or related in whole or in part to
any loss, damage, or injury, including death, that may be sustained by me or any third party or loss or damage to
any property belonging to me or any third party arising out of or related to use of the Product.
9. I agree that the site of any lawsuit arising out of or related in any way to the Product shall be in the State of Califor-
nia and that this Agreement shall be governed by and construed in accordance with the laws of the State of Califor-
nia, without application of any principles of choice of law. In the event that a lawsuit arises between me and XTRA-
CYCLE, I agree and covenant to pay for any and all attorney fees and costs and expenses incurred by XTRACYCLE in
enforcing this Agreement. If any portion of this Agreement is held to be invalid by a court of law, then I agree that it
is intended that all the remainder of the Agreement shall, notwithstanding, continue in full force and effect.
I HAVE CAREFULLY READ THESE TERMS AND FULLY UNDERSTAND THEIR CONTENT. I AM AWARE THAT THIS IS AN
ASSUMPTION OF RISK, A WAIVER AND RELEASE OF LIABILITY AND AN AGREEMENT TO INDEMNIFY AND THAT IT
FORMS A CONTRACT BETWEEN MYSELF AND XTRACYCLE, AND MY EXECUTION OF THIS AGREEMENT IS AT MY OWN
FREE WILL, WITHOUT ANY INDUCEMENT, REPRESENTATION, ASSURANCE OR GUARANTY OF ANY NATURE BEING
MADE TO ME. I INTEND THIS AGREEMENT TO BE A COMPLETE AND UNCONDITIONAL RELEASE OF ALL LIABILITY TO
THE GREATEST EXTENT ALLOWED BY LAW.
I CERTIFY THAT I AM AT LEAST EIGHTEEN (18) YEARS OF AGE AND THAT I UNDERSTAND THE TERMS OF THIS AGREE-
MENT. I AGREE TO COMMUNICATE THE TERMS OF THIS AGREEMENT TO ANY INDIVIDUAL(S) THAT I ALLOW TO USE
THIS PRODUCT. I ALSO ACKNOWLEDGE AND AGREE THAT THIS AGREEMENT SHALL BIND MY HEIRS, AGENTS, PER-
SONAL REPRESENTATIVES AND ASSIGNS.
Page 12 6684.000/411853.2