Yaasa The Space Saver Desk Basic S User manual

1
Yaasa
Desk Basic S &
Frame Basic S
Extended original
operating instructions

2
Safety Measures, Residual Risk, and
Danger Notices
The Yaasa Desk Basic S is an electronically-adjustable sit-stand table (table) for home and
ofce use. The Yaasa Frame Basic S is an electronically-adjustable sit-stand table frame
(table) for home and ofce use. Full operation and assembly instructions (instructions) are
available on the Yaasa website (www.yaasa.com).
YAASA GmbH accepts no liability for damages or injuries that may ensue from incorrect
assembly or use of this table.
CAUTION
SAFETY NOTICE: Read all notices and instructions before the rst use of the product.
Pay attention to risks relating to burns, res, electrical shock or other damages
to people and property in order to minimize them. Save these instructions in the
vicinity of the table for quick access, if required. Pass these safety instructions on
to any subsequent users of the table. All persons who use the product or who are
responsible for installation, service, or repair work, must follow these instructions
caref ully.
ATTENTION: Essentialafety measures should be taken whenever using
electronic devices. INAPPROPRIATE USE OR THE NEGLECT OF THESE
INSTRUCTIONS AND NOTICES WHEN USING THE TABLE CAN LEAD TO
SERIOUS INJURY OR PROPERTY DAMAGE.
Yaasa Desk Basic S: The table may only be used as an adjustable desk for changes between
sitting and standing positions. The table may only be used indoors and in dry areas (ofces or
similar). Any other use of this product is not recommended and occurs at the user’s own risk.
Yaasa Frame Basic S: The table may, in combination with a suitable tabletop, only be used as
an adjustable desk (table) for changes between sitting and standing positions. The table may
only be used indoors and in dry areas (ofces or similar). Any other use of this product is
not recommended and is performed at the user’s own risk. Unless explicitly indicated in this
manual, all functions relate to a full-assembled table and not to the table frame alone.
Appropriate Use
ENGLISH TRANSLATION OF THE ORIGINAL OPERATING INSTRUCTIONS
Yaasa Desk Basic S/Frame Basic S

3
This appliance can be used by children from 8 years and above and people
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the hazards involved.
Children under the age of 8 must maintain a safe distance from the table, the
control unit, and the buttons of the operational control.
The table may only be used for the purposes described in this manual.
Unauthorized access must be avoided!
The table may not be loaded with more than 80kg. The table may not be operated
continuously for more than 2 minutes. After, the table must “rest” for 18 minutes
before it can be operated again.
The Yaasa Desk Basic S features a collision detection system. This function aims
to reduce system damage and injuries through crushing. Responsibility for the
appropriate use of the product lies with the user.
Two people are required to complete assembly of the table. The instructions
must be followed completely at all times. Special care must be taken during the
movement of heavy parts and at any crushing or shearing points.
The height-adjustment function may only be used after the full and appropriate
assembly of the table.
The table must never be used as a lifting aid for people.
The table’s screw connections must be secured and checked in regular intervals.
The table and its components may not be changed, enhanced or rebuilt in any way.
Do not use parts that are not recommended by the manufacturer.
Never open electrical components, housing, or covers. This entails the risk of
electrical shock. Maintenance and repair work may only be performed by trained
personnel. Before cleaning or maintenance, disconnect all cables from the power
outlet.
While the table is being used, no one may stand or sit on the table, nor may they
climb or lie underneath it. During reset processes there is a risk of crushing
between the table legs and feet.
When the table moves upwards or downwards, you must maintain a safe distance
in order to avoid collisions or crushing between the table and its surrounding
objects or persons. The user requires an unobstructed view of the table and its
surroundings in order to observe the movement of the table and to avoid collisions,
injuries or damages while the table is in movement. Do not store objects under
the desk that are taller than 64 cm. While operating the table, pay close attention
EN

4
to other people, as well as window frames, radiators, chairs, cabinets and other
furniture.
The power cable represents a trip hazard. Ensure that the cable routing allows
for the table’s entire range of movement and is not obstructed. The cable must be
kept away from heated surfaces. Ensure suitable cable routing for devices that are
placed on the table itself.
Keep liquids away from the table and its electronic components.
Do not use the table if:
• Cables or plugs are damaged
• The table does not work as described in the instructions
• The table has fallen over or is otherwise damaged
• The table has become wet
EN

5
Setup And Use Of The Table
After the frame is assembled, the tabletop must be mounted according to the
instructions. The provided screws should be used. The minimum tabletop thickness
is 18 mm. Yaasa recommends the use of laminated chipboard or a solid-wood surface.
Tabletops with a length of 90 cm to 130 cm and a depth of 50 cm to 70 cm are
permitted. The maximum load on the table is 100 kg. The weight of the tabletop must
be calculated in the maximum load. After assembly, the levelers on the feet must be
adjusted so that the table stands evenly and is stable.
Position the table in the vicinity of an outlet and plug in the power cable. The table is
now ready for use.
Functions
A complete description of the Yaasa Desk Basic S’s functions can be found in the operating
instructions on www.yaasa.com.
CHANGING THE TABLE HEIGHT
Press the arrow buttons on the handset in order to move the table upwards or downwards.
DUTY CYCLE
The table may not be operated for more than 2 minutes continually. If this limit is exceeded,
an 18-minute rest phase is triggered. After this pause, the table can be used as normal again.
Excessive use of the table may cause permanent damage to the electronic components and
void the warranty.
EN
2
1
MANUAL RESET
• Press and hold the down button until the table stops moving downward. Then, release the
button.
• Press and hold the down button again for about 5 seconds, until the LED starts ashing.
• Press and hold the down button again until the table goes upward by a few millimeters.
KEY LOCK
To activate the key lock, press and hold the up and down buttons simultaneously for about 5
seconds. The LED then ashes for 3 seconds – after this, the table can no longer be adjusted.
To deactivate the key lock, press the up and downs buttons again for about 5 seconds. The
LED will ash again for 3 seconds, indicating that the table can be used normally.

6
FAQs and Troubleshooting
Technical Characteristics
Complete troubleshooting instructions and FAQs are available on www.yaasa.com.
In your delivery:
Frame:
Adjustment interval:
Adjustment speed:
Column Type:
Max. Load:
Sound level:
Weight (Complete Product):
Input:
Switching Cycles:
Additional Function(s):
Plug type:
Tabletop:
Operational control:
YAASA DESK BASIC S
Table frame and tabletop
Powder-coated steel with
4 levelers with a 8 mm
thread.
70 - 118 cm
30 mm/s
1 Stage
80 kg
<50 dB unloaded
28 kg
230 V / 50 Hz / 1.5 A
2 Minutes on;
18 Minutes off
Collision Detection
Euro (3 m Cable Length)
Melamine-coated chipboard
with all-round plastic
edging
Up and down
USB-A Port: 5V DC / 2A
Output voltage
YAASA FRAME BASIC S
Table f rame
Powder-coated steel with
4 levelers with a 8 mm
thread.
68 - 116 cm
30 mm/s
1 Stage
100 kg
<50 dB unloaded
18 kg
230 V / 50 Hz / 1.5 A
2 Minutes on;
18 Minutes off
Collision Detection
Euro (3 m Cable Length)
Up and down
USB-A Port: 5V DC / 2A
Output voltage
EN

7
EN
TABLE SIZE WEIGHT A B C D E F G H I J
120x70cm 28 kg 70 120 70-118 359,2 4,1 63-111 745 9 7, 9

8
EN
Disposal
Return And Guarantee
Contact
Right of exchange or return for up to 14 days after the receipt of goods.
Warranty of 2 years (in cases of normal use).
For any problems or questions regarding the product, please contact the online shop from
which you bought the product by phone or email.
For all other information, recurring problems, or for further questions, please contact:
YAASA GmbH
Radlpass Straße 19
8502 Lannach, Austria
www.yaasa.com
[email protected]
© YAASA GMBH 2023
The product must be disposed of according to local regulations
for recycling. The separation of product waste contributes to
the reduction of incineration and landll disposal and reduces
potentially harmful effects on human health and the environment.

9
Manufacturer: YAASA GmbH
Radlpass Straße 19
8502 Lannach, Austria
Person authorized to compile Walter Koch
the technical documents: YAASA GmbH, Managing Director
Radlpass Straße 19
8502 Lannach, Austria
The manufacturer hereby declares, on its sole responsibility, that the following product:
Product name: Yaasa Desk Basic S
Product description: Electrically height-adjustable sit-stand desk
for ofce and home use
Type designation: Yaasa Desk Basic S EU
Serial number: see type plate
fullls all of the relevant provisions of the following directives:
• Directive (2006/42/EC) on machinery (Machinery Directive); as per Annex I Section 1.5.1
of the Machinery Directive, the safety goals of Directive (2014/35/EU) regarding
electrical equipment for use within certain voltage limits (Low-Voltage Directive) are also
covered
• Directive (2014/30/EU) on electromagnetic compatibility
(Electromagnetic Compatibility Directive)
In particular, the following harmonized standards and/or technical specications were
applied:
• EN ISO 12100:2010
• EN 60335-1:2012 + A11:2014 + A13:2017 • EN 62233:2008
• EN 50663:2017 • EN 50581:2012
• EN 62479:2010 • EN 61000-6-1:2007
• EN 61000-6-3:2007 + A1:2011 • EN 61000-6-2:2005
• EN 61000-3-2:2014 • EN 61000-3-3:2013
Complete technical documentation is available. Operating instructions for the machines
have been provided in the original version. It is hereby conrmed that the abovementioned
products correspond to the stated EC/EU directives. This declaration shall become invalid if
the products are reworked or modied without our permission.
© YAASA GmbH 2023
EN
EC/EU Declaration of Conformity

10
www.yaasa.com
YAASA GmbH
Radlpass Straße 19
8502 Lannach
REVISION 4
02/2023