Yakima FlipSide 4 User manual

1033438B-1/18
FlipSide 4
FLIPSIDE (1X)
WHEEL STRAP (12X)
WRENCH (1X)
WASHER (1X)
HITCH BOLT (1X)
SAFETY CLIP (1X)
HITCH LOCK (1X)
PIVOT BUSHING (1X)
PIVOT PLATE (1X)
LARGE WASHER (1X)
PIVOT BOLT (1X)
LOCK WASHER (1X)
PIVOT COVER (1X)
HEX WRENCH (1X)
Part #1033438 Rev.B
IMPORTANT WARNING
ITIS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR TO OTHERS. YOU ARE RESPONSIBLE FOR
SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS
FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS SUPPLIED WITH
YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION OR USE. IFYOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO
MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A
PROFESSIONAL INSTALLER SUCH AS AQUALIFIED GARAGE OR AUTO BODY SHOP.
USE ONLY YAKIMA ADAPTERS WITH
THIS PRODUCT. DO NOT USE ANY
OTHER BRAND TONGUE ADAPTER.
PURCHASE
SEPARATELY:
HitchSki
Carries up to 6 pr. skis or 4
snow boards.
Part #8002418
See at www.yakima.com
DO NOT USE THIS
PRODUCT WITH
HITCH EXTENDERS.
For Your
Safety
Warranty
Registration
on-line
YAKIMA.com
TOOLS REQUIRED:
ADJUSTABLE WRENCH

1033438B-2/18
INSTALL TONGUE TO MAST
Insert bushing
through tongue
around shaft
from mast.
Put pivot plate in place.
INSTALL BOLT, AND WASHER.
FOR 1-1/4" HITCHES: REMOVE THE 2" HITCH ADAPTER, AND SLEEVE.
Remove the hex
bolt from the
adapter using hex
wrench.
FOR 2" HITCHES: PROCEED TO NEXT STEP.
Remove the adapter
from the tongue.
Remove the sleeve
from the tongue.
Use this hole.
• IMPORTANT: Pivot plate must fit
over step on axle.
• Install bolt, passing through large
washer.
• TIGHTEN with the wrench.
Insert mast through
tongue.

1033438B-3/18
INSTALL HITCH BOLT, LOCK-WASHER, AND WASHER.
TIGHTEN with
adjustable wrench.
LOCK TONGUE TO THE HITCH.
IF SPARE TIRE CAUSES
INTERFERENCE, DO NOT
USE THIS PRODUCT!
Align the holes in
the receiver to the
holes in the base.
INSERT TONGUE INTO
VEHICLE'S HITCH.
• Insert the key and
lock the lock.
• Close the cap.
• Attach hitch lock.
Extend arms. RAISE ARMS COMPLETELY.
Pull knob.
Rotate Flipside to upright
position.
Pull the lever forward
to release the arms from
locked-down position.
Arms will lock
into position.
CAUTION
Keep fingers away from
ALL moving parts!
• Install safety pin.
INSTALL PIVOT COVER.
Being careful
not to pinch
your hand, snap
the pivot cover
into place
Install bolt,
lock washer,
and washer
from right side
of receiver.
• Pull knob.
• Fold FlipSide down.

1033438B-4/18
• Alternate bike directions to avoid
interference.
• Stabilize bike, secure all straps.
LOAD REMAINING BIKES.
Pull straps tightly over frame, hook into place.
The straps can be routed
under the brake cables.
CRADLE POSITIONING
Attach one rubber strap to each
cradle and stabilizer.
stabilizer
LOAD LARGEST OR HEAVIEST BIKE FIRST.
• Always load first
bike with chain
away from vehicle.
• Compress cradles
against stabilizer.
Stabilize
the bike
frame in
the cradle
Arrange
bikes for best
stabilization.
Close cradles while
loading bikes.
To slide cradles along
the carrier arms, close
cradle and stabilizer.

1033438B-5/18
• Access lock cable from
recess at rear of mast.
CAUTION: DO NOT FOLD FLIPSIDE DOWN OVER
A HOT EXHAUST PIPE! THE FLIPSIDE CAN FOLD
DOWN TO EITHER SIDE, ALWAYS FOLD IT AWAY
FROM YOUR VEHICLE'S EXHAUST PIPE.
• Unload the bikes.
• Pull knob at rear of mast.
• Fold mast down.
TO FOLD MAST
DOWN AND ACCESS
THE REAR:
LOWERING THE ARMS
• Unload bikes.
• Pull up slightly on arms
while pulling lever.
• Pull lever forward.
• Lower the arms completely.
CAUTION: KEEP FINGERS AWAY
FROM ALL MOVING PARTS!
NEVER OPERATE VEHICLE WITH
MAST IN DOWN POSITION!
LOCK BIKES TO CARRIER. • Pass cable through bike frame.
• Attach lock to pin.
• Lock the lock.
PERFORM SAFETY CHECKS
IF YOUR VEHICLE HAS A
REAR HATCH:
On some vehicles, hatch
interference is unavoidable.
Use caution when opening
your hatch.
• Mast must be locked into place when operating vehicle.
• Be sure the straps are hooked securely over the bike frames.
• Replace straps if cracked or worn.
• Be sure all hardware is secured according to instructions.
• Do not let bicycle tires hang near vehicle’s hot exhaust.