Yakima LOCKN'LOAD User manual

09-13-592-Rev2 1/4
• Please read instructions carefully before installation.
• Check the contents of kit. Contact your YAKIMA dealer if any parts appear missing or damaged.
• Clean your Platform prior to itting the YAKIMA LockNLoad High Lift Jack Holder.
• Place these instructions in the vehicle’s glove box after installation is complete.
FIRST TIME INSTALLATION
KIT CONTENTS
ITEM COMPONENT QTY
1. High Lift Jack Holder
Clamp Bracket
x1
2. High Lift Jack Holder
Padlock Bracket
x1
3. Clamp x1
4. M8 Spring Nut x4
5. M8 Socket Head
Capscrew 25 mm
(Crossbars only)
x4
6. M8 Spring Washer x4
7. M8 Washer x4
8. M10 Washer x2
9. M10 Spring Washer x2
10. M10 x 40 mm
Hex Screw
x1
11. M10 x 30 mm
Hex Screw
x1
12. Allen Key 6 mm x1
13. M8 Socket Head
Capscrew 20 mm
(Platform only)
x4
®
PLATFORM SOLD SEPARATELY
HIGH LIFT JACK HOLDER
1
2
3
4
5
6
7
8
9
10
11
12
13
LockNLoad
™

09-13-592-Rev2 2/4
INSTALLATION
INSERT SPRING NUTS
- PLATFORM
Insert 4x M8 Spring Nuts
into Platform sides and
slats via the cut outs as
shown. Determine the
best slat spacing for the
High Lift Jack Brackets
based on the length of
Jack you will be carrying.
The Spring Nuts
do not need to be
rotated into place.
1
POSITION SPRING NUTS IN CHANNELS
Slide Spring Nuts along channels so they are positioned as close to the
Platform edge/end of crossbars as possible. The Brackets can be used
as a guide for spacing. Ensure nuts are equally spaced as shown. The
Allen Key can be used to assist nut movement within channel.
2
INSERT SPRING NUTS
- LockNLoad BAR
Insert 4x M8 Spring Nuts into
crossbar channels as shown.
Push Spring Nuts down into crossbar
channels and twist to lock into place.

09-13-592-Rev2 3/4
SECURE HIGH LIFT JACK
Secure your high lift jack
onto the Padlock Bracket
using the M10 x 40 mm Hex
Screw, M10 Spring Washer
and M10 Washer as shown.
4
With the high lift
jack securely in place,
swing the clamp down
over the jack arm and
tighten the M10 x
30 mm Hex Screw.
The jack can be secured with a padlock
(not supplied) as shown for added security.
NOTE - Padlock Bracket shown
SECURE BRACKETS - PLATFORM
Secure both Brackets onto the Platform via the Spring
Nuts using 2 x M8 Socket Head Capscrews 20 mm, 2 x M8
Spring Washers and 2 x M8 Washers per bracket as shown.
Tighten all Capscrews with supplied Allen Key to 4-5 Nm
3
SECURE BRACKETS - LockNLoad BAR
Secure both Brackets onto the Platform via
the Spring Nuts using 2 x M8 Socket Head
Capscrews 25 mm, 2 x M8 Spring Washers
and 2 x M8 Washers per bracket as shown.
Tighten all Capscrews with
supplied Allen Key to 4-5 Nm

09-13-592-Rev2 4/4
www.yakima.com.au
YAKIMA PRODUCTS, INC.
4101 Kruse Way
Lake Oswego, OR
97035-2541
USA
888 925 4621
YAKIMA AUSTRALIA PTY. LTD
17 Hinkler Court
Brendale, QLD 4500
Australia
1800 143 548