Yeastar Technology MyPBX User manual

Standard/GSM
User Manual
Version 2.10.0.99
Yeastar Technology Co., Ltd.

MyPBX Standard/GSM User Manual
www.yeastar.com Page 2
Table of Contents
1. Introduction............................................................................................4
1.1 Features............................................................................................4
1.2 Hardware Specifications....................................................................... 5
1.2.1 Exterior Appearance......................................................................5
2. System set up......................................................................................... 6
2.1 Connection Drawing ............................................................................ 6
2.2 Connecting Ethernet Line.....................................................................6
2.3 Supplying Power.................................................................................6
3. Managing MyPBX..................................................................................... 8
3.1 Administrator Login.............................................................................8
3.2 Status Monitor.................................................................................... 9
3.2.1 Line Status...................................................................................9
3.3 Basic............................................................................................... 10
3.3.1 Extension................................................................................... 10
3.3.1.1 Analog Extensions (FXS) ........................................................ 11
3.3.1.2 VOIP Extension ..................................................................... 13
3.3.2 Trunk ........................................................................................ 17
3.3.2.1 Analog Trunk（FXO）............................................................. 17
3.3.2.2 GSM Trunk ........................................................................... 19
3.3.2.3 VOIP Trunk........................................................................... 19
3.3.2.4 Service Provider.................................................................... 21
3.3.3 Outbound Routes ........................................................................ 23
3.3.3.1 New Outbound Route............................................................. 23
3.3.3.2 Delete Outbound Route.......................................................... 25
3.3.4 Auto Provision ............................................................................ 25
3.3.4.1 Phone .................................................................................. 25
3.3.4.2 IP Phone .............................................................................. 26
3.4 Inbound Call Control ......................................................................... 27
3.4.1 IVR ........................................................................................... 27
3.4.1.1 Create IVR............................................................................ 27
3.4.1.2 Delete IVR............................................................................ 29
3.4.2 Queues...................................................................................... 29
3.4.3 Custom Prompts ......................................................................... 31
3.4.4 Ring Groups ............................................................................... 33
3.4.4.1 Create Ring Group................................................................. 33
3.4.4.2 Delete Ring Group................................................................. 34
3.4.5 Inbound Routes .......................................................................... 34
3.4.5.1 Create Inbound Route............................................................ 35
3.4.5.2 Delete Routes ....................................................................... 38
3.4.6 Blacklist..................................................................................... 38

MyPBX Standard/GSM User Manual
www.yeastar.com Page 3
3.4.5.1 Create Blacklist..................................................................... 38
3.5 Other Settings.................................................................................. 39
3.5.1 DISA ......................................................................................... 39
3.5.2 Conferencing .............................................................................. 40
3.5.3 Business Hours........................................................................... 41
3.5.4 Feature Codes ............................................................................ 41
3.5.5 Paging Groups............................................................................ 44
3.6 System Settings ............................................................................... 46
3.6.1 Options...................................................................................... 46
3.6.2 Music on Hold Prompts................................................................. 47
3.6.3 SIP Settings ............................................................................... 47
3.6.4 IAX Settings............................................................................... 50
3.6.5 Voicemail Settings....................................................................... 52
3.6.6 Network Setting.......................................................................... 54
3.6.7 DHCP Server .............................................................................. 55
3.6.8 External Storage......................................................................... 56
3.6.9 Password Settings....................................................................... 57
3.6.10 Date and Time .......................................................................... 58
3.6.11 Backup and Restore................................................................... 59
3.6.12 Reset and Reboot...................................................................... 60
3.6.13 Firmware Update....................................................................... 61
3.7 Reports ........................................................................................... 62
3.7.1 Call Logs.................................................................................... 62
3.7.2 System Info ............................................................................... 63
4. Access MRI........................................................................................... 65
5. Use MyPBX ........................................................................................... 71
5.1 Make outbound call........................................................................... 71
5.1.1 Sample Routing via PSTN Trunk.................................................... 72
5.2 Incoming call.................................................................................... 75
5.2.1 Sample Routing to an IVR ............................................................ 75
APPENDIX A FAQ.................................................................................... 77
APPENDIX B How to Configure Autobackup................................................ 78
APPENDIX C How to Configure NAT setting................................................ 80
APPENDIX D How to Use Auto Provision .................................................... 83
APPENDIX E How do I configure distinctive ring tones................................. 86

MyPBX Standard/GSM User Manual
www.yeastar.com Page 4
1. Introduction
MyPBX —An IP-PBX for Small Businesses/Home Office
MyPBX is a standalone embedded hybrid PBX for small businesses and remote
branch offices of larger organizations (2-100 users per site). MyPBX also offers
a hybrid solution (a combination of VoIP applications using legacy telecom
equipment) alternative for enterprises who are not yet ready to migrate to a
complete VoIP solution.
Applications
1.1 Features
● Auto-provision ● Do Not Disturb(DND)
● Blind Transfer ● Firewalls*
● BLF Support ● Follow me
● Blacklist ● Interactive Voice Response (IVR)
● Call Detail Records(CDR) ● Intercom / Zone Intercom
● Call Forward ● Music On Hold
● Call Parking ● Music On Transfer
● Call Recording ● Paging / Zone Paging
● Call Pickup ● Queue
● Call Routing ● Ring Group
● Call Transfer ● Route by Caller ID
● Call Waiting ● Skype Integration (Skype for SIP)
● Caller ID ● Three-way Calling
● Conference ● T.38
● Define Office Time ● Voicemail
● Direct Inward System Access(DISA) ● Voicemail to email
● DIDs ● Voicemail forwarding
● Distinctive Ringtone
Note: the features with indication (*) will be supported in next version.

MyPBX Standard/GSM User Manual
www.yeastar.com Page 5
1.2 Hardware Specifications
1.2.1 Exterior Appearance
Front Side
Figure 1-1 MyPBX Front Panel Picture
No. Identifying
①Green LED：Indicates correct power is being supplied to the unit
②Green LED：Indicates the MyPBX is fully functional.
③Green LED：Indicates stable Ethernet0 connection
④Green LED：Indicates stable Ethernet1 connection
⑤Red LED：Indicates presence of an FXO/GSM module.
Green LED：Indicates presence of an FXS module .
LED Blinking- Red blinking：No connection between FXO port and PSTN
LED Alternating - Red and Green (slow blink)：FXO port is receiving an incoming
call.
LED Alternating - Red and Green (fast blink)：FXO port is in use
LED Dual - Green and Red blinking：FXS port is ringing
LED Dual - Green and Red blinking：FXS port is in use
①② ③④ ⑤

MyPBX Standard/GSM User Manual
www.yeastar.com Page 6
2. System set up
2.1 Connection Drawing
2.2 Connecting Ethernet Line
MyPBX provides two 10/100M Ethernet ports with RJ45 interface and LED
indicator.Plug Ethernet line into MyPBX’s Ethernet port, and then connect
the other end of the Ethernet line with a hub, switch, router, LAN or WAN.
Once connected, check the status of the LED indicator. A yellow LED
indicates the port is in the connection process, and a green LED indicates the
port is properly connected.
2.3 Supplying Power
MyPBX utilizes the high-performance switch power supply, which supplies
the required power for the unit.
AC Input: 100~240V
DC Output: 12V, 3A
PSTN
PSTN
Normal Phone
IPPhone
601
602
603
604
FXS Lines LAN
IPProvider
Soft Phone
Router
GSM

MyPBX Standard/GSM User Manual
www.yeastar.com Page 7
Please follow the steps below to connect the MyPBX unit to a power outlet:
1. Connect the small end of the power cable to the power input port on the
MyPBX back panel, and plug the other end of the cable into a 100VAC
power outlet.
2. Check the Power LED on the front panel. A solid green LED indicates that
power is being supplied correctly.

MyPBX Standard/GSM User Manual
www.yeastar.com Page 8
3. Managing MyPBX
3.1 Administrator Login
From your web browser, input the IP address of the MyPBX server.
If this is the first time you are configuring MyPBX, please use the default
settings below:
IP Address: http://192.168.5.150
Username: admin
Password: password
Figure 3-1

MyPBX Standard/GSM User Manual
www.yeastar.com Page 9
3.2 Status Monitor
3.2.1 Line Status
Figure 3-2
MyPBX Status Description:
Extensions:
1) : Extension is unregistered
2) : Extension is idle
3）: Extension is ringing
4）: Extension is busy in a call
Trunks:

MyPBX Standard/GSM User Manual
www.yeastar.com Page 10
VOIP Trunk:
Status
Unregistered: Trunk registration failed.
Registered: Succeed registration, trunk is ready for use.
Request Send: Registering.
Waiting: Waiting for authentication.
FXO Trunk:
Status
Idle: The port is idle.
Busy: The port is in use.
Disconnected: The port hasn’t connected the PSTN line.
More detail message, please refer to the LED identifying of front panel.
GSM Trunk:
Status
Idle: The port is idle.
Busy: The port is in use.
Signal
: No signal.
: Poor.
: Average.
: Good.
: Excellent.
3.3 Basic
3.3.1 Extension
Extension has two types: Analog extensions (FXS) and VOIP extensions (SIP
extension or IAX extension).

MyPBX Standard/GSM User Manual
www.yeastar.com Page 11
Figure 3-3
3.3.1.1 Analog Extensions (FXS)
Edit Analog Extensions
On the administration page of FXS extensions, click ‘Edit’ on the extension that
you want to edit, and modify the following information on the popup window
1) General
·Extension
The numbered extension, i.e. 1234, that will be associated with this particular
User / Phone.
·Name
A character-based name for this user, i.e. ‘Bob Jones’
·Caller ID
The Caller ID (CID) string will be used when this user calls another internal user.
2) Voicemail
·Voicemail Access PIN #
Voicemail Password for this extension, i.e. ‘1234’.
·Send Voicemail to Email Address
This option defines whether or not voicemails/Fax are sent to the Email address
as an attachment.
Note: Please ensure that all voicemail settings are properly configured on the
System Settings -> Voicemail Settings page before using this feature.

MyPBX Standard/GSM User Manual
www.yeastar.com Page 12
3) Flash
·Hook Flash Detection
Sets the amount of time, in milliseconds, that must pass since the last
hook-flash event received by MyPBX before it will recognize a second event. If a
second event occurs in less time than defined by Hook Flash Detection, then
MyPBX will ignore the event. The default value of Flash is 1000 ms, and it can be
configured in 1ms increments.
4) Group
·Pickup Group
If this extension belongs to a pickup group, any calls that ring this extension can
be picked up by other extensions in the same pickup group by dialing the Call
Pickup feature code (default *4).
Note: *4 is the default setting, it can be changed under Feature Codes ->
General -> Call Pickup.
5) Follow me (Call Forwarding)
This function sets inbound call forwarding on an extension. An administrator can
configure Follow Me for this extension.
6）Other Options
.Call Waiting
Check this option if the extension should have Call Waiting capability.If this
option is checked, the ‘When busy’ follow me options will not be available.
.User Web Interface
Check this option to allow the user to login to the MyPBX User Web interface,
which can be used to access voicemail and extension recordings. Users may
login to the MyPBX User Web interface by using their extension number and
voicemail PIN # as the login and password respectively.
.Ring Out
Check this option if you want to custom the ring time. Tone will stop over the
time defined.

MyPBX Standard/GSM User Manual
www.yeastar.com Page 13
Figure 3-4
3.3.1.2 VOIP Extension
A VOIP extension is an SIP/IAX Account that allows an IP Phone or an IP Soft-
Phone client to register on MyPBX.
1. Add VOIP Extension
Go to Extensions VOIP Extensions Create New Extension
1) General
·Type
Extension type: SIP or IAX.
SIP – Identifies whether the extension sends and receives calls using the VoIP
protocol SIP.
IAX - Identifies whether the extension sends and receives calls using the VoIP
protocol IAX.
·Extension
The numbered extension, i.e. 1234, that will be associated with this particular

MyPBX Standard/GSM User Manual
www.yeastar.com Page 14
User / Phone.
·Password
The password for this extension, Ex: ‘12t3f6’
·Name
A character-based name for this user, EX: ‘Bob Jones’
·Caller ID
The Caller ID will be used when this user calls another internal extension.
2) Voicemail
·Enable Voicemail
Check this box if the user should hae a voicemail account.
·Voicemail Access PIN #
The voicemail Password for this extension, i.e. ‘1234’.
3) Mail Setting
This option defines whether or not voicemails are sent to an Email Address as
attachment.
·Enable Send Voicemail
Once enabled, the voicemail or Fax will be sent to email as an attachment.
·Email Address
Email address use to receive the voicemail or Fax.
Note: Please ensure that the section 'SMTP Settings For Voicemail'(in the
'Voicemail Settings') have been properly configured before using this feature.
4) VoIP Settings
·NAT
This setting should be used when the system is using a public IP address,
communicating with devices hidden behind a NAT device (such as a broadband
router). If you have one-way audio problems, you usually have problems with
your NAT configuration or your firewall's support of SIP and/or RTP ports.
·DTMF Mode – RFC2833, Info, Inband, Auto.
5) IP Restriction
·Enable IP Restriction
Check this option to enhance the VoIP security for MyPBX. If this option is
enabled, only the permitted IP or Subnet mask will be able to register this
extension number. In this way, the VoIP security will be enhanced.
·Permitted ‘IP address/Subnet mask’
The input format should be ‘IP address’+’/’+’Subnet mask’.
e.g."192.168.5.100/255.255.255.255" means only the device whose IP
address is 192.168.5.100 is allowed to register this extension number.
e.g."192.168.5.0/255.255.255.0" means only the device whose IP address is
192.168.5.XXX is allowed to register this extension number.

MyPBX Standard/GSM User Manual
www.yeastar.com Page 15
6) Group
·Pickup Group
If this extension belongs to a pickup group, any calls that ring this extension can
be picked up by other extensions in the same pickup group by dialing the Call
Pickup feature code (default *4).
Note: *4 is the default setting, it can be changed under Feature Codes ->
General -> Call Pickup.
6) Follow me (Call Forwarding)
This function sets inbound call forwarding on an extension. An administrator can
configure Follow Me for this extension.
7）Other Options
.Call Waiting
Check this option if the extension should have Call Waiting capability.If this
option is checked, the ‘When busy’ follow me options will not be available.
.User Web Interface/Web Access
Check this option to allow the user to login to the MyPBX User Web interface,
which can be used to access voicemail and extension recordings. Users may
login to the MyPBX User Web interface by using their extension number and
voicemail PIN # as the login and password respectively.
.Ring Out
Check this option if you want to custom the ring time. Tone will stop over the
time defined.

MyPBX Standard/GSM User Manual
www.yeastar.com Page 16
Figure 3-5
2. Add Multiple Extensions
Go to Extensions VOIP Extensions Add Multiple Extensions.
1) Choose the number of extensions that you would like to create.
2) Choose the type of extension that you would like to create.
3) Fill in the starting extension number.

MyPBX Standard/GSM User Manual
www.yeastar.com Page 17
Figure 3-6
3. Edit VOIP Extension
Click ‘Edit’ on VOIP Extension administration page or click ‘Modify Selected
Extensions’ to edit extension.
3.3.2 Trunk
There are three types of trunks: Analog trunks (FXO), VOIP and Service
Provider trunks.
Figure 3-7
3.3.2.1 Analog Trunk（FXO）
1. Edit Analog Trunk（FXO）

MyPBX Standard/GSM User Manual
www.yeastar.com Page 18
On the analog Trunk administration page, click ‘Edit’ on the selected trunk and
modify its properties in the popup window:
1）General
·Trunk Name
A unique label used to identify this trunk when listed in outbound rules,
incoming rules, etc. Ex: 'Port 5'
·Volume Setting
Used to modify the volume level of this trunk. Normally, this setting does not
need to be changed.
2）Advanced Options
·Busy Detection
Busy Detection is used to detect far end hang-up or for detecting a busy signal.
Select “Yes” to turn this feature on.
·Busy Count
If Busy Detection is enabled, it is also possible to specify how many busy tones
to wait for before disconnecting. The default is 4, but better results can be
achieved if set to 6 or even 8. Remember, the higher the number, the more time
required to release a channel. A higher setting lowers the probability that you
will encounter random hang-ups
·Busy Pattern
If Busy Detection is enabled, it is also possible to specify the cadence of your
busy signal. In many countries, it is 500msec on, 500msec off. Without Busy
Pattern specified, MyPBX will accept any regular sound-silence pattern that
repeats <Busy Count> times as a busy signal. If you specify Busy Pattern, then
MyPBX will further check the length of the tone and silence, which will further
reduce the chance of a false positive disconnect.
·Caller ID Start
This option allows you to define the start of a Caller ID signal:
Ring: Start when a ring is received (Caller ID Signaling: Bell_USA, DTMF).
Polarity: Start when a polarity reversal is started (Caller ID Signaling:
V23_UK,V23_JP,DTMF).
Before Ring: Start before a ring is received (Caller ID Signaling: DTMF).
·Caller ID Signaling
This option defines the type of Caller ID signaling to use. It can be set to one of
the following:
Bell: bell202 as used in the United States
v23_UK: Used in the UK
v23_JP: Used in Japan
DTMF: Used in Denmark, Sweden, and Holland

MyPBX Standard/GSM User Manual
www.yeastar.com Page 19
Figure 3-8
3.3.2.2 GSM Trunk
1. Edit GSM Trunk
1）General
·Trunk Name
A unique label used to identify this trunk when listed in outbound rules,
incoming rules, etc. Ex: 'gsm1'
·Volume Setting
Used to modify the volume level of this trunk. Normally, this setting does not
need to be changed.
Figure 3-9
3.3.2.3 VOIP Trunk
1. Add SIP Trunk
Input correct SIP information (provided by VOIP provider). Inaccurate
information will prevent the trunk from registering.
·Type
SIP – Identifies whether the trunk sends and receives calls using the VoIP
protocol SIP.
·Provider Name
A unique label to help you identify this trunk when listed in outbound rules,
incoming rules etc. Ex: 'yeastar'.
·Hostname/IP
Service provider’s hostname or IP address.5060 is the standard port number
used by SIP protocol. Don’t change this part if it is not required.
.Domain

MyPBX Standard/GSM User Manual
www.yeastar.com Page 20
VoIP provider’s server domain name.
·Username
Username of SIP account. Used for SIP trunk registration.
·Password
Password of SIP account.
.Authorization name
Used for SIP authentication. Leave this blank if not required.
.Online number
Define the online number that expected by ‘Skype Connect’ and some other SIP
service providers. Leave this field blank if it's no required.
·Maximum Channels
Controls the maximum number of outbound channels (simultaneous calls) that
can be used on this trunk. Inbound calls are not counted against the maximum.
Leave blank to specify no maximum.
Figure 3-10
2. Add IAX Trunk
Input correct IAX information (provided by VOIP provider). Inaccurate
information will prevent the trunk from registering.
·Type
IAX – Identifies whether the trunk sends and receives calls by using the VoIP
protocol IAX.
·Provider Name
A unique label to help you identify this trunk when listed in outbound rules,
incoming rules etc. Ex: 'yeastar2'.
·Hostname/IP
Service provider’s hostname or IP address. 4569 is the standard port number
used by IAX protocol. Don’t change this part if it is not required.
·Username