yeedi Vac Max User manual

yeedi vac station
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUAL DE INSTRUCCIONES
MANUEL D'INSTRUCTIONS
MANUALE D'USO
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ

7EN
Robot
Instruction Manual Edge Brush Mopping Pad PlateWashable Mopping Pad
1. Package Contents/1.1 Package Contents
Note: Figures and illustrations are for reference only and may differ from actual product appearance.
Product design and specications are subject to changes without notice.
Instruction Manual
Power Cord Dust Bag
Dust Container
Base
Base Socket ScrewsScrew Driver
Ramp Extension

8
EN
1. Package Contents/1.2 Product Diagram
Anti-Collision Sensors and Bumper
AUTO Mode Button
Multi-function
Cleaning Tool
Robot
Mapping Sensor
Power Switch
Wi-Fi Indicator
RESET Button
Bottom View
Anti-Drop Sensors
Carpet Detection
Sensor
Mopping Pad Plate
Slot
Water Outlet
Driving Wheels
Battery
Charging Contacts
Anti-Drop Sensors
Reservoir
Edge Brush
Universal Wheel
Main Brush
Main Brush
Release Button

9EN
Reservoir
Water Inlet
Mopping Pad Plate
Reservoir Release Button
Washable Mopping Pad
Dust Bin
Dust Bin Handle
Release Button
Filter Net
Self-empty Outlet
Sponge Filter
High Efciency Filter
Self-empty Station
Lid Release Button
Indicator Light
Infrared Singnal Emitter
Self-empty Inlet Self-empty Station Pins
Ramp Extension

10
EN
Self-empty Station (Back)
Self-empty Station (Top)
Power Cord Port
Dust Bag Socket
Dust Evacuation Tube
Power Cord Wrap
Blower Cover
Self-empty Station (Bottom)
Power Cord
Base Screw Socket
Dust Evacuation Tube
+ Tube Cover
Ramp Extension Slot
Dust Evacuation Tube
Cover Set Screws

11 EN
2. Operating and Programming/2.1 Notes Before Cleaning
Tidy up the area to be cleaned by putting
furniture, such as chairs, in their proper place.
During the rst use, make sure each room door is
open to help Robot fully explore your house.
It may be necessary to place a physical
barrier at the edge of a drop to stop the
unit from falling over the edge.
Put away objects including wires,
cloths and slippers, etc. on the
oor to improve the cleaning
efciency.
Before using the product on a rug
with tasseled edges, please fold
the rug edges under.
Please do not stand in narrow
spaces, such as hallways, and
make sure not to block the
Detection Sensor.

12
EN
2. Operating and Programming/2.2 Preparation
Please remove all protection materials on Robot and Self-empty
Station before use.
1
2
Connect the Dust Container and the Base
Tighten the Base Socket Set Screws

13 EN
3Assemble Self-empty Station
4Install the Ramp Extension
5Self-empty Station Placement

14
EN
6Install Edge Brush
7Power ON
8Charge Robot
Note: When Robot completes the cleaning cycle or when the battery
gets low, Robot automatically returns to the Self-empty Station to
recharge itself. Robot can also be sent back to the Self-empty Station
at any time by using the yeedi App or by pressing the AUTO Button on
the robot for 3 seconds.
Empty remaining water from the Reservoir and remove the Mopping
Pad Plate before charging Robot.
6.5

15 EN
2. Operating and Programming/2.3 yeedi App
To enjoy all available features, it is recommended to control your Robot via the yeedi App.
Wi-Fi Indicator LightBefore you start, make sure that:
Tips:
If you have any problems during the Wi-Fi setup process, refer to the
Troubleshooting > Wi-Fi Connection section in this manual.
• Your mobile phone is connected to a Wi-Fi network.
• The 2.4GHz band wireless signal is enabled on your router.
• The Wi-Fi indicator light on Robot is slowly ashing.
Slowly flashing Disconnected to Wi-Fi or
waiting for Wi-Fi connection
Rapidly flashing Connecting to Wi-Fi
Solid Connected to Wi-Fi
yeedi

16
EN
2Pause
3Wake Up
Note: The robot’s Control Panel stops glowing after the robot is
paused for a few minutes. Press the AUTO Mode Button on Robot to
wake it up.
Press the AUTO button on Robot to wake it up
4Power OFF
Note: When Robot is not working, it is recommended to keep it
switched ON and charging.
2. Operating and Programming/2.4 Start, Pause, Wake Up, Power Off
1Start

17 EN
1
2
Note:
1. To prolong the service life of the reservoir, it is recommended to use puried water or softened water for the mopping system.
2. If you need to clean the carpet, please uninstall the Mopping Pad Plate rst.
3. Empty the reservoir after Robot nishes mopping.
Click
2. Operating and Programming/2.5 Mopping System

18
EN
Before performing cleaning and maintenance tasks on Robot, turn the robot OFF and unplug the Self-empty Station.
3. Maintenance/3.1 Mopping System
1 42
5
3
7 86

19 EN
Dust Bin
Note: 1. Please rinse the lter with water as shown above. 2. Do not use nger or brush to clean the lter.
3. Be sure to dry out the lter for at least 24 hours after washing.
3. Maintenance/3.2 Dust Bin and Filters
3 6
41
2 5
7
8

20
EN
Main Brush
Edge Brush Mapping Sensor
Note: A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
123
3. Maintenance/3.3 Main Brush, Edge Brush and Mapping Sensor

21 EN
Note: Before cleaning the robot’s Charging Contacts and Self-empty Station Pins, turn the robot OFF and unplug the Self-empty Station.
3. Maintenance/3.4 Other Components

22
EN
3. Maintenance/3.5 Self-empty Station
Self-empty Station Pins Infrared Signal Emitter
Note: Before performing cleaning and maintenance on Self-empty Station, unplug it rst.
* For a proper maintenance, wipe with a clean dry cloth, and avoid using any detergent or cleaning spray.
Dust Bag
1
* The Dust Bag will be sealed by the handle so the dust will not leak.
Dispose the Dust Bag

23 EN
2 4
3
Clean the Blower Cover
Install the Dust Bag
Close the Dust Container Lid

24
EN
Dust Evacuation Tube
Unscrew the Dust Evacuation
Tube Cover
Uninstall the Dust Evacuation
Tube Cover
Clean the Dust Evacuation Tube

25 EN
To keep Robot running at peak performance, perform maintenance tasks and replace parts with the following frequencies:
A multi-function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
Note: yeedi manufactures various replacement parts and ttings. Please contact Customer Service for more information on replacement parts.
Robot Part Maintenance Frequency Replacement Frequency
Washable Mopping Pad After each use Every 50 washings
Reservoir/Mopping Pad Plate After each use /
Edge Brush Once every 2 weeks Every 3-6 months
Main Brush Once per week Every 6-12 months
Sponge Filter/High Efciency Filter Once per week Every 3-6 months
Universal Wheel
Anti-Drop Sensors Bumper
Mapping Sensor
Charging Contacts
Self-empty Station Pins
Once per week /
3. Maintenance/3.6 Regular Maintenance