Zennio MAXinBOX 8 Guide

Technical Documentation
© Zennio Avance y Tecnología S.L. Edition 3 Further information www.zennio.com Page 1 / 2
MAXinBOX 8
MAXinBOX 8. Multi-function actuator with 8 outputs 16A
ZN1IO-MB8 Technical Documentation
FEATURES
8 different configurable outputs:
Shutter channels (up to 4).
Individual outputs (up to 8).
Manual output operation with push button and LED
status indicator.
Suitable for capacitive loads, maximum 140 µF.
Logical functions included.
Output timing facilities.
Total data saving on power failure
Size 67 x 90 x 80 mm (4.5 DIN units).
DIN rail unit assembly (EN 50022), with snap fit clamp.
No external power supply required other than the bus.
KNX BCU integrated.
Possibility to connect different phases in adjoining
outputs.
CE directives compliant.
Programming/test button: short button press to set programming
mode. If this button is held while plugging the device into the KNX
bus, it goes into safe mode. If this button is held more than 3
seconds, the device goes into manual mode (test mode)
LED: programming mode indicator (red). When the device goes into
safe mode, it blinks (red) every half second. The manual mode is
indicated by the colour green. During start up (after reset or power
failure) and if the device is not in safe mode, LED blinks in blue for a
few seconds
6
1
4
5
7
3
2
Figure 1. MAXinBOX 8
GENERAL SYSTEM SPECIFICATIONS
CONCEPT
DESCRIPTION
Type of device
Electric operation control device
KNX supply
Voltage (typical)
29VDC SELV
Voltage range
21…31V DC
Maximum consumption
160mW
Bus connection
Typical bus connector TP1, 0,50 mm² section
External power supply
No
Ambient temperature
from 0ºC to +55ºC
Storage temperature
from -20ºC to +70ºC
Ambient humidity
5 to 95% RH (no condensation)
Storage humidity (relative)
5 to 95% RH (no condensation)
Complementary characteristics
Class B
Safety class
II
Operation type
Continuous operation
Device action type
Type 1
Electrical solicitations period
Long
Type of protection
IP20, clean environment
Assembly
Independent control assembly device to be mounted inside of electrical panels
with DIN rail (EN 50022).
KNX bus failure response
Data saving and relays open if channel configured as shutter.
Response when restarting KNX bus
Data recovering and output status change according to programming when
recovering.
Operation indication
Programming LED indicates programming mode (red) and test mode (green).
Output status LED indicators reflect current output state.
Weight
284 g.
PCB CTI index
175 V
Enclosure
PC FR V0 halogen free
1. Upper
outputs
2. Lower output
screws
3.Programming/Test
LED
4.KNX
connector
5.Programming/Test
button
6.Output control
button
7.Output status LED
indicator

Technical Documentation
© Zennio Avance y Tecnología S.L. Edition 3 Further information www.zennio.com Page 2 / 2
WIRING AND ASSEMBLY DIAGRAMS
SAFETY INSTRUCTIONS
Do not connect Mains Voltage (230 V) or any other external voltages to any point of the bus.
Connecting an external voltage might put the entire KNX system at risk.
Make sure during the installation that there is always sufficient insulation between the mains voltage 230V and the bus or
the extension inputs.
Once the device is installed, the output terminal should not be accessible.
OUTPUTS SPECIFICATIONS AND CONNECTIONS
Contact type
Potential free outputs through bistable relays with tungsten pre-contact.
Disconnection type
Micro-disconnection
Rated current by output
16(6)A * 250V AC (4000 VA) 16(6)A * 30V DC (480W)
Maximum inrush current
800A/200μs (fluorescent lamps)
165A/20ms (resistive lamps)
Outputs per common
1 individual output
Different phases connection
Possibility to connect different phases in adjoining outputs
Maximum current
80A
Maximum power
Resistive load
4000W
Inductive load
1500W
Connection type
Terminal block (screw)
Recommended cable section
0,25 mm² to 4 mm²
Cable type
Stranded or solid wire.
Maximum response time
50 ms
Expected life
Mechanical (min)
3 million operations (60cpm)
Electrical (min.)
100.000 cycles at max. current (6cpm and resistive load)
Attaching MAXinBOX 8 to DIN rail:
Removing MAXinBOX 8 from DIN rail:
Figure 3. Installation of MAXinBOX 8 on DIN rail
Figure 2. Wiring examples (from left to right): channel A as shutter channel and individual outputs with the same and
different phases.