Zennio MAXinBOX FC 0-10V VALVE User manual

© Zennio Avance y Tecnología S.L. Edition 4 Futher information www.zennio.com Page 1/2
MAXinBOX FC 0-10V VALVE
2-pipe or 4-pipe fan coil controller with 0-10VDC valve and up to 4 fan speed
ZCL-FC010V TECHNICAL DOCUMENTATION
FEATURES
•2 x 0-10VDC individual outputs for valve control.
•4 individual outputs (suitable for capacitive loads, maximum 140µF)
capable of controlling up to 4 fan speeds.
•4 analog/digital inputs.
•Manual output operation in 0-10VDC and individual outputs with push
button and status indicator LED.
•Logical functions.
•Output timing facilities.
•Total data saving on power failure.
•DIN rail unit assembly (EN 50022), with snap fit clamp.
•Size 67 x 90 x 80 mm (4.5 DIN units).
•KNX BCU integrated
•Possibility to connect different phases in adjoining outputs.
•Conformity with the CE directives (CE-mark on the right side).
1. Analog/Digital inputs
2. 0-10VDC outputs
3. Output status LED indicator
4. Output control button
5. Programming/Test LED
6. Lower outputs
7. KNX connection
8. Programming/Test button
Figure 1: MAXinBOX FC 0-10V VALVE
Programming/test button: short press to set programming mode. If this button is held while plugging the device into the KNX bus, it enters the safe
mode. If this button is held for more than 3 seconds, the device enters the test mode.
Programming/Test LED: programming mode indicator (red). When the device enters the safe mode, it blinks (red) every half second. The manual mode
is indicated by the green color. During the start-up (reset or after KNX bus failure) and if the device is not in safe mode,it starts a blue blinking sequence.
GENERAL SPECIFICATIONS
CONCEPT
DESCRIPTION
Type of device
Electric operation control device
KNX supply
Voltage (typical)
29VDC SELV
Voltage range
21..31VDC
Maximum
consumption
Voltage
mA
mW
29VDC (typical)
11
319
24VDC¹
15
360
Connection type
Typical TP1 bus connector for 0.80mm Ø rigid cable
External power supply
Not required
Operation temperature
0°C .. +55°C
Storage temperature
-20°C .. +55°C
Operation humidity
5 .. 95% (No condens.)
Storage humidity
5 .. 95% (No condens.)
Complementary characteristics
Class B
Protection class
II
Operation type
Continuous operation
Device action type
Type 1
Electrical stress period
Long
Degree of protection
IP20, clean environment
Installation
Independent device to be mounted inside electrical panels with DIN rail (EN
50022)
Minimum clearances
Not required
Response on KNX bus failure
Data saving according to parameterization
Response on KNX bus restart
Data recovery according to parameterization
Operation indicator
The programming LED indicates programming mode (red) and test mode
(green). Each output LED indicates its status
Weight
248g
PCB CTI index
175V
Housing material
PC FR V0 halogen free
¹ Maximum consumption in the worst case scenario (KNX Fan-In model)
1
7
8
3
5
6
2
4

© Zennio Avance y Tecnología S.L. Edition 4 Futher information www.zennio.com Page 2/2
SAFETY INSTRUCTIONS
•Installation should only be performed by qualified professionals according to the laws and regulations applicable in each country.
•Do not connect the mains voltage nor any other external voltage to any point of the KNX bus; it would represent a risk for the entire
KNX system. The facility must have enough insulation between the mains (or auxiliary) voltage and the KNX bus or the wires of other
accessories, in case of being installed.
•Once the device is installed (in the panel or box), it must not be accessible from outside.
•Keep the device away from water and do not cover it with clothes, paper or any other material while in use.
•The WEEE logo means that this device contains electronic parts and it must be properly disposed of by following the instructions at
http://zennio.com/weee-regulation.
OUTPUTS SPECIFICATIONS AND CONNECTIONS
CONCEPT
DESCRIPTION
Number of outputs
4
Output type
Potential-free outputs through bistable relays
with tungsten pre-contact / Micro-disconnection
Rated current per output
AC 16(6)A @ 250VAC (4000VA)
DC 7A @ 30VDC (210W)
Maximum load
per output
Resistive
4000W
Inductive
1500VA
Maximum inrush current
800A/200μs
165A/20ms
Different phases connection
Possibility of connecting different phases in
adjoining outputs
Maximum current per block
40A
Connection method
Screw terminal block
Cable cross-section
1.5-4mm² (IEC) / 26-10AWG (UL)
Outputs per common
1
Maximum response time
10ms
Mechanical lifetime (min. cycles)
3 000 000
0-10V OUPUT SPECIFICATIONS AND CONNECTIONS
CONCEPT
DESCRIPTION
Número de salidas
2
Ouput type
0-10VDC
Maximum load per output
1.5mA
Connection method
Screw terminal block
Cable cross-section
0.5-2.5mm² (IEC) / 26-12AWG (UL)
Output per common
1
INPUTS SPECIFICATIONS AND CONNECTIONS
CONCEPT
DESCRIPTION
Number of inputs
4
Inputs per common
4
Operation voltage
+3.3VDC in the common
Operation current
1mA @ 3.3VDC (per input)
Switching type
Dry voltage contacts between input and
common
Connection method
Screw terminal block
Cable cross-section
0.5-2.5mm² (IEC) / 26-12AWG (UL)
Maximum cable length
30m
NTC probe length
1.5m (up to 30m)
NTC accuracy (@ 25°C)
±0.5°C
Temperature resolution
0.1°C
Maximum response time
10ms
⚠In order to ensure the expected status of the relays,
please check thatthe device is connected tothe KNX bus
before energizing the power circuit.
WIRINGDIAGRAMS
Figure 2: wiring example for 4-pipe fan coil with 4-
speed fan (up) and for 2-pipe fan coil with 3-speed
fan (down).
Attaching MAXinBOX FC 0-10V VALVE to DIN rail:
Removing MAXinBOX FC 0-10V VALVE from DIN rail:
* The micro switch number 2 in the ZN1IO-DETEC-P must be in Type B position to work properly.
INPUTSCONNECTION
Any combination of the next accessories is allowed on the inputs:
Zennio temperature
probe.
Up to two motion sensors
can be plugged into the
same device input (parallel
wiring)
Motion sensor screw
terminal.
Motion sensor references:
ZN1IO-DETEC-X
ZN1IO-DETEC-P*
Temperature Probe
Motion Sensor
Switch/Sensor/
Push button
G/L
G0/N
G/L
G0/N
G/L
G0/N
G/L
G0/N
0-10V outputs according to the number of fan
coil pipes:
Fan Coil
0-10V output
Valve function
4 pipes
V1
Cooling valve
V2
Heating valve
2 pipes
V1
Cooling and/or
heating valve