ZKTeco TL400B User manual

Installation Instruction
TL400B
Version: 1.2
Date: Nov.,2017

Diagram
Before Installation
1
C
K
D
L
B
A
C
D
E
H
F
G
IJ
M
N
O
P
Q

M
B
Packing List
G
20mm
Q
8mm
D
50mm
LN
30mm 40mm
Mounting hardware
package for 35-50mm
door thickness
Mounting hardware
package for 50-65mm
door thickness
D
70mm
LN
45mm 55mm
H
70mm
2
A
E
FI
J
K
C
Note: To ensure proper functioning of the device only use the
mounting hardware package for your door thickness.

1. Check door thickness, prepare the mounting hardware package and
cylinder.
Door Preparation
Door Thickness
(mm)
D Spindle Length
(mm)
N Screw Length
(mm)
L Screw Length
(mm)
Q Screw Length
(mm)
E Cylinder Length
(mm)
35-50 50 40 30 8 40
50-65 70 55 45 8 50
3
2. Check door open direction.
Note 1: There are two types of mortise (F): one is for left open, the other is for right open. Please use the
correct one.
Note 2: There are two types of strike plate (I): one is for inward open, the other is for outward open. Please
use the correct one.
3
I
I
I
I
FF
FF
Left inward Right inward
Left outward Right outward Standpoint

Installation
1. Drill holes on the door.
Note 1: Align the template along the vertical center line of the mortise (F) at the desired handle height, and
tape it to door.
Note 2: Mark the holes first, then start drilling.
center line of the handle
desired handle height
door thickness
35~80mm
55mm
Backset
Indoor OutdoorOutdoorIndoor
Installation Template
Installation
Template
door thickness
35~80mm
4

G
F
Installation
2. Install the mortise(F).
Indoor Outdoor
Indoor Outdoor
OutdoorIndoor
G
F
2.1 The clutch dot must be vertically
centered with mortise dot, then put
this side toward outdoor.
2.2 Installing mortise (F) by
inserting screws (G).
2.3 The mortise cable must
through out door hole.
5

3.Install lock cylinder(E).
H
E
H
Note: Installing the cylinder in right direction, 
put the key hole toward outdoor, then
insert screw (H) to secure cylinder(E).
4.Install spindle(D).
D
Note: Ensure the dot of clutch is vertically
upward.
D
Indoor Outdoor
OutdoorIndoor
Indoor
Indoor
Outdoor
Outdoor
6

5.Install outdoor unit(B) with gasket(C).
B
C
Indoor Outdoor
Indoor Outdoor
5.1 Put the gasket (C) on
the outdoor unit(B).
5.2 Attach outdoor unit (B) to
door by putting it through
door holes.
Note: Connect the outdoor unit (B)
cable to the mortise. There are two cable on
the outdoor unit, please connect appropriate
cable according to the size of joint.
7

B
C
K
KC
L
6. Install mounting plate (K) with
gasket (C) on the door.
L
7. Install spindle (D) on the door.
D
Indoor Outdoor Outdoor
OutdoorIndoor
Indoor
6.1 Put the gasket (C) on
the mounting plate (K).
6.2 Inserting screws (L) to
secure the outdoor unit(B).
7.1 Inserting the spindle
(D) to the clutch.
8

N
8. Install indoor unit (M).
Q
9. Install the battery .
N
Q
P
Note: Push cable into the hole.
M
Alkaline Battery
Indoor
Indoor
Indoor Outdoor
Outdoor
Outdoor
8.1 Connect the indoor
unit (M) cable to the
outdoor unit (B).
8.2 Inserting the screws
(N) (Q) to Secure the
indoor unit (M).
Note: Please use
Alkaline battery to
make sure the lock
can work properly.
9

10.Mark and drill holes for striking.
3mm
69mm
38mm
180mm
130mm
15mm
(Depth)
25mm
(Depth)
27.5mm
16.5mm
21mm
25mm
I
J
G
10

11.Test the lock by mechanical key(A) or registered fingerprint.
11
A
Remove the cover on the key
hole with screwdriver or nails.
Insert the key into key hole
and rotate 90°.
AB Mechanical Key Instruction:
1.Key A is coated with brass color, which is used only for
lock installer and upfitter.
2.Key B is packed in the sealed plastic wrap for safety,
which is used for house owner.
3.Once Key B is used, Key A will be disabled to open the
lock.
Key A
Key B
Key A
Note: AB key system is available by contacting sales.
11

Cautions
1. The default setting of the device allows ANY fingerprint to unlock.
2. Please register at least one administrator for the newly installed lock. Without
administrator, no registration for any normal user is allowed.
3. The lock is equipped with mechanical keys for manually unlocking. Please keep the
mechanical keys in a safe place.
4. To power on the lock, four alkaline AA batteries (not included) are required.
Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.
5. Do not remove batteries when the lock is in working state.
6. Please replace the battery soon when the lock prompts the voice of low battery.
7. If there is no activity performed on the lock for 10 seconds the fingerprint sensor
will go to sleep.
8. For best results, apply clean fingers to the fingerprint sensor.
Tips
How to change the handle direction?
Press down the component pointed by the arrow.
At the same time, rotate the handle at 180°.
Then release your hand from the pressed component.
Press down
the component
180°
12

ZK Building, Wuhe Road, Gangtou, Bantian, Buji Town,
Longgang District, Shenzhen China 518129
Tel: [phone]
Fax: [phone]
www.zkteco.com
© Copyright 2017. ZK Teco Inc. ZKTeco Logo is a registered trademark of ZKTeco or a related company. All other product and company names mentioned are used
for identification purposes only and may be the trademarks of their respective owners. All specifications are subject to change without notice. All rights reserved.