Zkteco F18 User manual

(1) Post the mounting template on the

wall. Drill the holes according to

the marks on the template (holes

Version: V1.1 Date: Nov. 2011

(2) Remove the screw on the (3) Take away the back plate.

(5) Tighten the screw on the bottom,

plate on the wall according to the

(4) Fix the plastic pad and the back

RS485 TCP/IP

Lock

Sensor

①

③

Alarm

RS232/RS485 Converter

②

NC LOCK

DC12V

NC LOCK

NO LOCK

FR 107

+12V +12V

+12V

GND GND

GND

GND GND

GND

SEN SEN

SEN

BUT BUT

BUT

BELL+ BELL+

BELL+

BELL- BELL-

BELL-

NO LOCK

DC12V

FR 107

DC12V

DC Power

DC12V

DC Power

FR 107

DC12V

GND

+12V

Exit Button

⑤

Reader

④

Bell

Door Bell

BUTTO N

EXIT

BUTTO N

⑦

⑥

+Alarm

Alarm Power

Exit Button

Door Sensor

for screws and wiring).

bottom of device.

Access Control System Function

(1) If a registered user verified, the device will export the

signal to unlock the door.

(3) If the d llegal , it will output an evice is removed i ly

(4) is External card reader supported.

(5) is it is External exit button supported, convenient to

alarm signal.

open the door inside.

(7) Supports , modes with RS485 TCP/IP to connect PC. One

PC can manage multiple devices.

(6) External door bell is supported.

①: ‘‘I’: device output current, ‘ ’: lock voltage, ’: lock currentULOCK ILOCK

(1) The system supports NO LOCK and NC LOCK. For example the NO LOCK (normally open at

(2) When the Electrical Lock is connected to the Access control System, you need to parallel one FR107

diode (equipped in the package) to prevent the self-inductance EMF affecting the system, do not

power on) is connected with ’‘ ‘NO’ and COM terminals, and the NC LOCK(normally close at power

3.Lock Connection

！

Warning: No operating with power on

(1) Share power with the lock:

ULOCK=12V, I-ILOCK>1A… ①

And the distance between the lock

Device shares power with the lock:

Does not shares power with the lock:

A. =12V I- ≤1A;ULOCK ILOCK

B ≠12V; . ULOCK

C. The distance between the lock and

Alarm Voltage output ≤ DC 12V

4. Other Parts Connection:

5. Power Connection:

Input DC 12V, 500mA (50mA standby). Positive

is connected with ‘+12V’, negative is connected

with ’GND’ (do not reverse the polarities).

(2) Does not share power with the lock:

2. Structure and Function

F18 Installation Guide

1. Equipment Installation

Wirin g Hole

Instru ction fo r the Mo unting P aper

Before t he devic e is fas tened, p leas e

stick th e paper to t he pla ce where y ou

want to in stall it , then m ake hole s and

lay cabl es accor ding t o the moun ting

paper.

F18 M ounti ng Pape r

(on ly for yo ur refe rence )

Fixin g Hole

NC1 NC1

NC1

NO1 NO1

NO1

COM1 COM1

COM1

NO2 NO2

NO2

COM2 COM2

COM2

fix the device to the back plate.

(2) Door sensor will detect the on-off state If the door is

unexpected opened or improperly closed, the alarm signal

(digital value) will be triggered.

mounting paper.

on) is connected with ‘NC’ ‘and COM’ terminals.

reverse the polarities.

and the device is equal or less

the device is more than 10 meters.

than 10 meters.

(1) Post the mounting template on the

wall. Drill the holes according to

the marks on the template (holes

Version: V1.1 Date: Nov. 2011

(2) Remove the screw on the (3) Take away the back plate.

(5) Tighten the screw on the bottom,

plate on the wall according to the

(4) Fix the plastic pad and the back

RS485 TCP/IP

Lock

Sensor

①

③

Alarm

RS232/RS485 Converter

②

NC LOCK

DC12V

NC LOCK

NO LOCK

FR 107

+12V +12V

+12V

GND GND

GND

GND GND

GND

SEN SEN

SEN

BUT BUT

BUT

BELL+ BELL+

BELL+

BELL- BELL-

BELL-

NO LOCK

DC12V

FR 107

DC12V

DC Power

DC12V

DC Power

FR 107

DC12V

GND

+12V

Exit Button

⑤

Reader

④

Bell

Door Bell

BUTTO N

EXIT

BUTTO N

⑦

⑥

+Alarm

Alarm Power

Exit Button

Door Sensor

for screws and wiring).

bottom of device.

Access Control System Function

(1) If a registered user verified, the device will export the

signal to unlock the door.

(3) If the d llegal , it will output an evice is removed i ly

(4) is External card reader supported.

(5) is it is External exit button supported, convenient to

alarm signal.

open the door inside.

(7) Supports , modes with RS485 TCP/IP to connect PC. One

PC can manage multiple devices.

(6) External door bell is supported.

①: ‘‘I’: device output current, ‘ ’: lock voltage, ’: lock currentULOCK ILOCK

(1) The system supports NO LOCK and NC LOCK. For example the NO LOCK (normally open at

(2) When the Electrical Lock is connected to the Access control System, you need to parallel one FR107

diode (equipped in the package) to prevent the self-inductance EMF affecting the system, do not

power on) is connected with ’‘ ‘NO’ and COM terminals, and the NC LOCK(normally close at power

3.Lock Connection

！

Warning: No operating with power on

(1) Share power with the lock:

ULOCK=12V, I-ILOCK>1A… ①

And the distance between the lock

Device shares power with the lock:

Does not shares power with the lock:

A. =12V I- ≤1A;ULOCK ILOCK

B ≠12V; . ULOCK

C. The distance between the lock and

Alarm Voltage output ≤ DC 12V

4. Other Parts Connection:

5. Power Connection:

Input DC 12V, 500mA (50mA standby). Positive

is connected with ‘+12V’, negative is connected

with ’GND’ (do not reverse the polarities).

(2) Does not share power with the lock:

2. Structure and Function

F18 Installation Guide

1. Equipment Installation

Wirin g Hole

Instru ction fo r the Mo unting P aper

Before t he devic e is fas tened, p leas e

stick th e paper to t he pla ce where y ou

want to in stall it , then m ake hole s and

lay cabl es accor ding t o the moun ting

paper.

F18 M ounti ng Pape r

(on ly for yo ur refe rence )

Fixin g Hole

NC1 NC1

NC1

NO1 NO1

NO1

COM1 COM1

COM1

NO2 NO2

NO2

COM2 COM2

COM2

fix the device to the back plate.

(2) Door sensor will detect the on-off state If the door is

unexpected opened or improperly closed, the alarm signal

(digital value) will be triggered.

mounting paper.

on) is connected with ‘NC’ ‘and COM’ terminals.

reverse the polarities.

and the device is equal or less

the device is more than 10 meters.

than 10 meters.

DATA1

DATA0

GND

+12V

GLED

RLED

BEEP

Access Control Panel

IWD1

+12V

BEEP

GLED

RLED

IWD0

GND

IP Address：192.168.1.100

Subnet Mask：255.255.255.0

IP Address：192.168.1.124

Subnet Mask：255.255.255.0

Switch

…

Side View Back View

Tamper Switch

Reset Button

(1) RS232 Mode:

Terminals definition, please refers to the right table:

About the terminals definition, please refers

to the right table.

RXD Pin3-Txd

TXD Pin2-Rxd

GND Pin5-Gnd

485+ RS485+

485- RS485-

485+

485-

485+ 485-

RS485 Bus

485+ 485- 485+ 485-

RS485

10. Cautions:

6. Wiegand Output

The device supports standard Wiegand 26

/ Wiegand 34 output, so you can connect it

7. Wiegand Input

supports to connect with card reader. an independent

The device has the function of Wiegand input signal . It

(Please use Wiegand signal extender in long distance or interference environment).

(2) To keep the stability of Wiegand signal, connect the device and the access control or card reader in

(1) Please keep the distance between the device and access control or card reader less than 90 meters

There are three modes that the PC software could communicate and exchange information with the device:

RS232, RS485 and TCP/IP, and the last two modes support remote control.

9. Communication

8.Other Functions

(1) Manual Reset:

(2) Restore Factory Settings:

(A) Crossover cable: The device and PC

(B) Straight cable: The device and PC connected

(3) TCP/IP Mode:

(2) RS485 Mode:

Operation: Press the tamper switch three times after the alarm being

other restart it.abnormality, you can use ‘Reset’ function to

If the device does not work properly because of misoperation or

button hole with than 2mm).a sharp tool (the tip diameter is less

Operation: Remove the black rubber cap, then stick the Reset

You can use the tamper switch to restore factory settings, such as

device number, system password, IP address, RS485 address.etc.

triggered 30 seconds, but no more than 60 seconds.

Terminals PC Serial Ports

Terminals Wire Name Color

Converter

！

Warning: No operating with power on

same ‘GND’ in any case.

They are installed each side of the door, to control the

Please use specified RS485 wire, RS485 active

converter and bus-type wiring.

Terminals:

to LAN/WAN through switch/Lanswitch.

connected directly.

with most of the access control devices by

RJ45-1 TX+ White-orange

RJ45-3 RX+ White-green

RJ45-6 RX- Green

485+

485-

TXD

RXD

GND

WD0

WD1

DATA0

GND

DATA1

lock and access together.

The user data won't be cleared. (2) We recommend that use the DC 3A/12V power supply. For details, please contact our technical

＂

(5) Please connect the GND before all the other wiring especially under the serious

＂electrostatic environment,

(3) Please read the terminals description and wiring by rule strictly. Any damage carefully

(4) Keep the e xpose d par t o f wire is less than 5mm to avoid unexpected connection, and result i n m achinery damage.

(1) Power cable is connected after all the o ther wiring. If the device is abnormally, please shutoperated

do wn the power firstly, then make some hot-necessary checking. Kindly remain that any

caused by improper operations will be out of the range of our guarantee.

to prevent the overlarge instantaneous electrostatic to damage device.

(6) If the power supply is a little long, please do not use the Internet

cable or other types of cable instead. When choosing the power supply cable, you should

consider that the transmission distance may cause voltage attenuation.

distance between and device

plugging may damag e device, and it is not included in the warranty.

(7) Please use specified RS485 wire, RS485 active converter, and adopt bus-type wiring. If the communication

personnel or sales.

now.

Two ways for TCP/IP connection:

wire is longer than 100 meters, it is needed to parallel a terminal resistance on the last device of RS485 bus,

and the value is about 120 ohm.

RJ45- TX Orange2 -