ZKTeco FaceKiosk-H10A User manual

Quick Start Guide
FaceKiosk-H10A
Version: 1.0
Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the
actual product and the written information in this manual.

1. Components
1
Bottom
Front
Rear Side
193.87mm
241.87mm
26.8mm
28mm
182mm
30mm
16mm 78mm
Φ5mm
Speaker
10.1-inch Touch Screen
Status Indicator
Binocular Camera
Card Reading Area
BUT SEN GND COM NO NC Ethernet
Port
Power In
Lock
Door Sensor
Exit Button
Status LED Description:
Green-The meeting room is available.
Red-The meeting room is occupied.
USB
Status Indicator
Microphone

2. Installation Procedure
2
Preparation before Installation
Prepare the necessary tools.
1.
Network Cable Marker Pen Small Cross
Screwdriver
6mm Expansion
Rubber Plugs
and Screws
Knife Large Cross
Screwdriver
Tape Measure 6mm Impact
Drill
Power Strip Level Ruler
Unpacking and Device Testing: Take out the power adapter, power cable and device from
the packing from the box one at a time. Connect the power cable to the device and turn it
on; check the device appearance for scratches and other defects.
2.

3
Turn on the device and make sure that the touch and other functions work properly.
3.
Knock on the wall to see whether the load-bearing wall is stable.
4.
Installation
Choose the Installation Location: Use a measuring tape to measure the installation
height of the device (it is recommended that the bottom of the device be 1.4m above the
ground), and use a marker to mark the installation position of the device.
1.
1.4m
l No reserved wiring hole position:

4
Mark the installation position of the rear hanging plate and the outlet position of the
network cable and power cable in parallel using a level ruler (the distance between the
device edge and the rear hanging plate fixing hole, the green mark in the figure is the rear
hanging plate fixing hole and the outlet position of the network cable and power cable,
unit: mm).
2.
30
8236
52
46
16
Drill holes at the wall marking point using a 6mm impact drill, then dig a hole between the
four hole positions (for network cable and power cable routing).
3.
Insert 6mm expansion rubber plugs into the mounting holes.
4.

5
Align the rear hanging plate with the wall and the installation holes and attach the rear
hanging plate with four tapping screws.
5.
Pull the network cable and power cable out of the rear hanging board from the cable
outlet and connect them into the device. Then align the device to the wall hanging holes
with the hooks on the rear hanging plate and hang it on the rear hanging plate.
6.
After aligning the bottom hook screw, insert and tighten the hook screw. Then connect the
power cable into the power strip and turn on the device.
7.

l Reserved wiring hole position:
Align the outlet hole of the rear hanging plate with the reserved outlet hole of the wall, use
the level ruler to make sure that the rear hanging plate parallel to the ground, and use a
marker to mark the position of the fixing holes of the rear hanging plate on the wall.
1.
For the rest of the installation steps, refer to Step 3 to 7 in the “No reserved wiring hole
position“ section.
2.
3. Door Sensor, Exit Button and Lock Connection
Door Sensor
ExitButton
+ -
+ -
FR107
-
ElectricLock
Power
BUT SEN GND COM NO NC
6

7
4. Home Screen
The device has two theme styles for the home page. It can be set in [Meeting Management] >
[Meeting Theme]. The default is technology style.
Technology Style
Business Style

Click the or button in the upper right corner to access the main menu.
Note: If the Super Administrator is not registered for the device, then tap to access the main menu.
If the device has a Super Administrator, then his/her verification is required to access the main
menu. For security purposes, it is advisable to register the Administrator while using the device for
the first time.
LAN Connection
Connect the network cable. On the main menu, tap on [Communication Setting] > [Ethernet
Setting] > [Ethernet] to set the network parameters.
5. Ethernet and Wi-Fi Connection
8

9