ZKTeco FA50 User manual

Installation Guide
FA50
Version: 1.0
Due to regular system upgrades and products, ZKTeco could not guarantee exact consistency between
the actual product and the written information in this manual.

- 1 -
Operation Instructions
1.
Figure 1-1
1. The device has two USB plugs, as shown in the below Figure 1-1.
Insert the USB cable "A" of FA50M into the USB port situated on the
host’s back, as shown in Figure 1-2.
Figure 1-2

- 2 -
2. Right-click on My Computer > Properties > Device Manager.
As shown in the figure below, if "Imaging devices" and "libusb-win32
Usb Devices" appear, users can continue using the same device. But
if "Imaging devices" and "libusb-win32 Usb Devices" did not appear,
it means that the device did not get connected appropriately.
Note: Generally, it is due to the insufficient power supply of the USB.
Just insert the USB cable "B" into the USB port of the host.
Figure 1-3

- 3 -
Steps to Run Demo for the First Time on Windows
2.
Double-click and open the "FA50 Demo" file, then click "FA50M
InstallDriver" to install the driver, as shown in Figure 2-1.
Driver Installation
Figure 2-1

- 4 -
On the Installation window, click "Next", as shown in Figure 2-2.
Figure 2-2
Then click "Finish" to successfully install the driver.
Figure 2-3

Demo Test Process
3.
1. Double-click and open the "FA50 Demo" file, and then open the
Demo Test software, as shown in Figure 3-1.
Figure 3-1
2. On the Demo Test software, firstly click "Open" to open the UVC
camera. The camera gets opened successfully only if "Camera
opened" gets displayed. Then the camera successfully captures the
image and displays it, as shown in Figure 3-2.
Figure 3-2
- 5 -

Secondly, as shown in Figure 3-3, click "Open" to open HID, and "HID
ope ned " wil l g et displayed, w hic h m ean s the HID ope ned
successfully.
Figure 3-3
3. Next, enter the registrant ID in the "User ID" field, then aim your
face at the camera, and click "Add User" to register the user ID.
And as shown in Figure 3-4, if "Add User successfully" appears, it
means that the user ID is successfully registered.
- 6 -
Figure 3-4

Click "Enroll face" to register face, and if "Enroll face successfully"
gets displayed, it means that face registration is successful.
Figure 3-5
As shown in Figure 3-6, the software displays the recognized
registration ID's username, and thus the recognition process is
complete.
Figure 3-6
- 7 -

To clear the user, click the "Clear User" button, and if " Clear User
successfully" gets displayed, it means that the user removal is
successful.
Figure 3-7
Precautions
4.
1. If the registration gets failed, click "Clear User" to clear the user
and register again.
- 8 -
Figure 4-1

- 9 -
2. When clicking "Open" to open HID, and if "No device found" gets
displayed, carry out the following solutions.
Insufficient power supply, plug in two USB ports.
The driver did not get installed successfully, repeat the steps of the
driver installation process.
Figure 4-2

- 10 -
3. Technical Parameters
Windows7
Windows Edition
Processor Intel® Pentium(R) CPU G3220 @ 3.00GHz 3.00 GHz
Windows , Linux , Android
Supported Operating System
4.00GB
Installed Memory (RAM)
64-bit Operating System
System Type

ZKTeco Industrial Park, No. 32, Industrial Road,
Tangxia Town, Dongguan, China.
Phone : +86 769 - 82109991
Fax : +86 755 - 89602394
www.zkteco.com
Copyright © 2021 ZKTECO CO., LTD. All Rights Reserved.