ZKTeco FBL6000 Pro Series User manual

Installation Guide
Flap Barrier Turnstile-FBL6000 Pro series
Applicable Model(s): FBL1000 Pro series, FBL1200 Pro series, FBL2000 Pro series,
FBL2200 Pro series, FBL4000 Pro series, FBL4200 Pro series, FBL5000 Pro series,
FBL5200 Pro series, FBL6000 Pro series, FBL6200 Pro series
Version: 1.1
Date: December 2019

FBL6000 Pro series installation guide 1
1 Material preparation
1. Tools: A measuring tape, an adjustable wrench, an impact drill and a small screwdriver (included
in the package).
2. Material: Fireproof PVC and insulation tube (diameter ≥25mm), standard three-core power
extension wire, M12 expansion screw (included in the package).
3. Thread the wires through the insulation tube before laying them underground.
4. Power wire and signal wire should be kept separately to avoid interference between strong and
weak power. It is recommended that the wiring is to be done by a professional. And the device
must be connected to the ground.
Below is the reference to FBL6000 Pro cabling.
Figure 1-1

2 FBL6000 Pro series installation guide
2 Power-on Test Prior to Installation
Test Procedure:
1. Connect a temporary test cable to the device and supply the input power of AC100-240V
adaptive to the device (Note that a ground cable must be connected.)
2. Wait 30 seconds till the wing gate completes the self-test procedure.
3. Start the air switch inside the wing gate to check whether the wing gate functions properly and
check whether the LED indicators function properly. If they all function properly, start the civil
installation. If an exception occurs, contact your sales agent.
Figure 2-1 Air Switch

FBL6000 Pro series installation guide 3
3 Electric and Civil Installation
1. Device installation conditions
The location where the device is installed must be a concrete flat surface so that the expansion
screws can be fastened firmly. If the planned foundation does not meet this criterion, consult
professional building or decoration personnel and create stable conditions for firmly fastening of the
wing gate.
2. Determination of the location of device installation
Decide the installation location based on the space needed as illustrated in Figure 3-1A and Figure 3-
1B.
Figure 3-1A Single-Passage Wing Gate Figure 3-1B Dual-Passage Wing Gate
3. Cable connection
For the location of the hole where the cables come out, please refer to Figure 3-2 below.
4. Device installation
a) Turn on the master machine and slave machine, adjust the wing arms to ensure that the wing
arms are in the same line and the distance between wings is 50 mm. Turn the wings to the OFF
state.
b) Test whether the infrared rays transmitted by infrared sensors on both sides align with each other.

4 FBL6000 Pro series installation guide
c) Make marks: Mark the screw hole of the base and chassis base edges on the ground.
d) Drill holes: Get ready a hammer drill and a 14 mm drill bit, vertically drill a hole with the depth of
80 mm in the screw hole centre marks.
Alternatively, drill holes according to installation hole positions, see Figure 3-2 for installation hole
positions. The unit of the figures in the drawings is mm.
Figure 3-2
e) Apply screw glue to the outer surface and threads of the expansion screws, insert expansion
screws, and put the master machine and slave machine in the marked positions. Use a level to
check whether the installation ground foundation is level. If not, use a pad for adjustment.
Note: Eight expansion screws must be completely inserted, as shown in Figure 3-3.

FBL6000 Pro series installation guide 5
Figure 3-3
5. Card Swiping Warning Lines
It is recommended that a warning line is set to prompt users to swipe cards outside the warning lines,
as shown in Figure 3-4.
Figure 3-4

6 FBL6000 Pro series installation guide
4 Menu Operation
Menu
There are four keys on the control panel, including "UP", "DOWN", "ENT", and "ESC". Press “ENT” to
modify settings, press "UP" and "DOWN" button to select a function, and press ”ESC” to exit.
The menu has the following options:
1. Passing mode
Two-way swipe (default)
Left free, Right swipe
Left swipe, Right free
Two-way free
Left prohibit, Right swipe
Left swipe, Right prohibit
Left prohibit, Right free
Left free, Right prohibit
Two-way prohibit
2. Opening speed
Low speed
Medium speed (default)
High speed
3. Closing speed
Low speed
Medium speed (default)
High speed
4. Volume setting
Volume: off
The value ranges from 1 to 16 (default 5).
1 is the minimum value; 16 is the maximum value.
5. Opening duration
After the gate is opened, it will be automatically closed if no one passes through within a certain
duration. The default value is 10 seconds. The value ranges from 5 to 60.
6. Reset the counter
Out counter
Into the counter
All (default)

FBL6000 Pro series installation guide 7
7. Gate closing delay time
Time: 0~10s (default 0s)
8. Trailing alarm detection
Mode: Close the door and audio alarm
Audio alarm only (default)
Disable the alarm function
9. Swiping mode
Method: Allow card swiping in the channel (default)
Do not allow card swiping in the channel
10. False direction entry
Mode: Close the door and audio alarm
Audio alarm only (default)
Disable the alarm function
11. Set fire signal
Enable (default)
Disable
12. Exchange voice of door opening
Yes
No (default)
13. Speed compensation of master machine
Compensation value: 000
1~20 (default: 000)
14. Speed compensation of slave machine
Compensation value: 000
1~20 (default: 000)
15. Gate closing mode
Out of the anti-pinch area, close the gate. (default)
Out of the channel, close the gate.
16. Memory opening
Whether to open: No (default)
Yes
17. System working mode
Mode: Working mode (default)
Test mode
Restore to factory
18. Version number
Version: V7.0.3

8 FBL6000 Pro series installation guide
5 Wiring Diagram
Below is the wiring diagram:
Figure 5-1

FBL6000 Pro series installation guide 9
Copyright©2019 ZKTECO CO., LTD. All rights reserved.
ZK Building, Wuhe Road, Gangtou, Bantian, Buji Town,
Longgang District, Shenzhen China 518129
Tel: [phone]
Fax: [phone]
www.zkteco.com