ZKTeco FHT2300 User manual

Installation Guide
Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the
actual product and the written information in this manual.
Full Height Turnstile Series
Applicable Models: FHT2300 Series, FHT2300D Series,
FHT2400 Series, FHT2400D Series
Doc Version: 1.1
Date: July 2022
English

It is recommended that the device must be installed on a horizontal solid platform with a height of
50mm to 100mm.
1.
After installation, check if the connection has been done correctly at the connecting points of the
ground wire, at the connector assemblies and wiring points of the circuits, as well as at each movable
part of the device. Any loose nuts, screws and other fasteners should be tightened in time to avoid any
failures caused by long-time operations.
4.
1
1 Installation Requirements
3. Make sure the ground wire of the system is reliably connected to avoid personal injuries or other
accidents.
2. It is also recommended that the device should not be used in the corrosive environment.
2 Preparation
To install the device you must have:
A Screwdriver: To remove or install the screw on the device.
A Pencil: To mark the device size and the screw hole.
A Electric Drill: To drill holes in accordance to the marked screw holes.
A Wrench: To secure the M12 expansion screw on the device.
A Tapeline: To measure the dimensions that need to be measured during the installation of the device.
A Hex Wrench: To remove or install the screw on the device.
Except for the hex wrench, all other tools should be prepared on your own.
Note:
The FHT2300 series, FHT2300D series, FHT2400 series and FHT2400D series have only slight differences
in appearance, but the installation, wiring and use are the same, and the following is an example of
FHT2300 series.

2
3 Installation
Place the frame to the installation site, and mark the floor following the periphery of the legs.
1.
① ②
②

Below is a drawing of the Full Height Turnstile Series mounting hole locations and dimensions in millimeters. There
may be errors, please refer to the actual product.
FHT2300Series
FHT2300DSeries
92.00
142.00
92.00
146.00
70.00
182.00
274.64 410.29 575.00
596.44
1242.89
594.44
576.44
92.00
92.00
92.00
146.00 146.00
142.00
92.00
274.64 416.40 197.50 155.00 197.50 416.40 274.64
142.00
97.44
596.44
594.44
1237.44
1242.89
3

FHT2400Series
8.00
47.63 682.39 146.00 164.00 146.00 682.39
8.02
47.63
91.65
142.00
91.65 66.07
565.07
1180.49
1206.07
FHT2400DSeries
629.31 575.00 70.00
91.65
564.37
562.37
142.00
91.65
1179.10
146.00
47.60
4

Take the frame aside and use the electric drill according to the drawn screw and wiring holes.
2.
3. Clean up the fragments and dust after drilling, then place the frame on the installation site again. Check
whether the drilled holes corresponds to the mark on the device.
4. User must pull the power cable and Ethernet from the machines and put them into the wire slot.
① ②
φ25mm
PVC pipe
Tether Cable
Power Cable
Ethernet
5
The input voltage for this full height turnstile is AC100-120V/200-240V. The PVC conduits are buried 100mm below
the ground, with the height of the exposed part not less than 100mm. To prevent water leakage to the conduit, the
conduit mouth needs to be bent back.
Note:

6
5. Align the frame with the drilled holes. Then, insert the bolts accordingly and fix them with a wrench.
Finally, insert the washer and nut, tighten it with a wrench.
6. Put the mainframe box on the frame, after connect the power cable, Ethernet and Tether Cable, fix up
with M12 screws.

Upward view
Note: Pay attention to the details in green circle, both of them should be in vertical direction.
The rotor direction should be place like this.
Planview of rotor of three arm
barrier (120°) position and
direction before installation
7

8
7. Put the whole rotating part in the middle of the frame and mainframe box and then fix up with screws
and connection block.
②
③ ④
①

9
BottomTop
Front

10
4Wiring Diagram
After fixing the device, open the mainframe-box to connect power wire and reader. Pull out the reader and power
cord from both sides of the column and connect to the corresponding interface.

ZKTeco Industrial Park, No. 32, Industrial Road,
Tangxia Town, Dongguan, China.
Phone : +86 769 - 82109991
Fax : +86 755 - 89602394
www.zkteco.com
Copyright © 2022 ZKTECO CO., LTD. All Rights Reserved.