ZKTeco SBTL8000 Series User manual

Installation Guide
Speed gates SBTL8000 series
Applicable Model(s): SBTL8000, SBTL8011, SBTL8022, SBTL8033,
SBTL8200, SBTL8211, SBTL8222, SBTL8233
Version: 1.0
Date: June 2019

SBTL8000 series installation guide 1
1Preparation
1. Tools: a measuring tape, an adjustable wrench, an impact drill and a small screwdriver (included
in the package).
2. Material: a PVC anti-fire and insulation tube (diameter≥25mm), standard three-core power
extension wire, tether cable (random configuration), M12 expansion screws (included in the
package).
3. Thread the connection wire of the device through the tube before assembly.
4. The power and signal wires should be set separately to easily distinguish strong and weak power.
Please invite professional personnel to complete the wiring. The device must be connected to
the ground.
Below is the outline and dimensions of SBTL8000:
Figure 1-1

2SBTL8000 series installation guide
2Installation
1. Prepare the tools for product installation and sort out the auxiliaries according to the packing list.
2. Drill holes after determining the hole positions based on the mounting template as shown in
Figure 2-1. Insert the expansion bolt into the holes accordingly.
Figure 2-1
3. Tighten the nut preliminarily, then connect the master and slave devices with wires.
4. Test the operations of the device after connecting it to the power supply with the temporary
cable. Make sure that the ground wire of AC power is connected to the cabinet of the device.
5. Turn on the air switch to test whether the device is working properly. Wait for 10 seconds for the
turnstile to complete the self-test program. At the same time, check if the indicators work
properly. If everything works fine, you can fasten the ground screw nuts and fix the device. If an
exception occurs, please contact your vendor.

SBTL8000 series installation guide 3
3Debugging Functions
Operating instruction
1. After powered on, the LCD screen on the control board will display the default state showing the
current working mode.
2. There are 4 buttons on the control board: UP, DOWN, ENT, and ESC, as shown in Figure 3-1.
UP: to move upwards or increase the value.
DOWN: to move downwards or decrease the value.
ENT: to enter a menu setting item or confirm the current modified value.
ESC: to return to the previous menu or cancel the current operation.
Menus
1. Position adjustment of the swing barrier
Type: zero (default)
Left limit
Right limit
2. Passing mode
Opening mode: Two-way swipe (default)
Left free, Right swipe
Left swipe, Right free
Two-way free
Left prohibit, Right swipe
Left swipe, Right prohibit
Left prohibit, Right free
Left free, Right prohibit
Two-way prohibit
3. Opening duration (Press ‘ENT’ to modify)
After the gate is opened, it will automatically close if no one passes through within a certain time
duration. The default value is 5 seconds. The value ranges from 2 to 60.

4SBTL8000 series installation guide
4. Reverse intrusion
Mode: Close the door and voice alarm
Voice alarm only (default)
Turn off reverse detection
5. Trailing alarm detection
Mode: Turn off trailing detection
Voice alarm only (default)
Close the door and voice alarm
6. Opening speed
Speed value: 1~20 (default 1)
7. Closing speed
Speed value: 1~20 (default 1)
8. Swiping mode
Method: Allow the card to be swiped in the channel (default)
Do not allow card swiping in the channel
9. Reset counter
Reset: Out counter (default)
Into the counter
All
10. Gate closing delay time
Time: 0~10 (default 0)
11. Brake unlock mode
Mode: Delay unlock (default)
12. Brake starting angle
Angle: 1~10 (default 3)
13. Fire alarm signal
Signal: right open

SBTL8000 series installation guide 5
Left open (default)
Shut down
14. Volume setting
Volume: off
The value ranges from 1 to 16 (default 5).
1 is the minimum value; 16 is the maximum value.
15. Audio prompt for gate opening swift
Enable or not: No (default)
Yes
16. Infrared anti-pinch
Mode: Turn off the anti-pinch feature
Enabling anti-pinch (default)
17. Infrared anti-pinch area
Area selection: Disable during In and out of infrared (default)
All infrared zone anti-pinch
18. Memory opening
Whether to open: No (default)
Yes
19. System working mode
Mode: working mode (default)
Test mode
Restore to factory
20. Version number:
Version: V9.0.0

6SBTL8000 series installation guide
4 Troubleshooting
Number Failure descriptions Analysis and solution
1 The mode indicator light does not respond
or the indication is incorrect.
Check that the control panel mode indicator
wiring is correct or that the contact is poor.
2 After swiping the card, there is only a speed
gate unlocked.
Check the mode setting of the master and
slave devices and the 8-core, 2-core
connection lines. See the wiring diagram for
the specific connection circuit.
3 The barrier doesn’t close when the opening
delay time is ended.
Check to see if the opening delay time is too
long or whether the IR sensor is covered.
4 When the gate is self-tested, the swing arm
is not in the normal closing position!
In the process of self-test, there are obstacles,
please remove the obstacles, restart the self-
test after power-on!

SBTL8000 series installation guide 7
5 Wiring Diagram
Below is the wiring diagram:
Figure 5-1

8SBTL8000 series installation guide
Copyright©2019 ZKTECO CO., LTD. All rights reserved.
www.zkteco.eu